Search NASA⌕ Search

Engineering topics

Unruh, James F.

Publications and source records attributed to Unruh, James F..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

General Aviation Interior Noise: In-Flight Source/Verification - Part 2

The technical approach made use of the Cessna Model 182E aircraft used in the previous effort as a test bed for noise control application. The present phase of the project reports on flight test results during application of various passive noise treatments in an attempt to verify the noise sources and paths for the aircraft. The data presented establishes the level of interior noise control that can be expected for various passive noise control applications within the aircraft cabin. Subsequent testing will address specific testing to demonstrate the technology available to meet a specified level of noise control by application of passive and/or active noise control technology.

Unruh, James F.↗
NASA NTRS2002

General Aviation Interior Noise: Noise Control Measure Evaluation - Part 3

The work reported herein is an extension to the work accomplished under NASA Grant NAG1-2091 on the development of noise/source/path identification techniques for single engine propeller driven General Aviation aircraft. The previous work developed a Conditioned Response Analysis (CRA) technique to identify potential noise sources that contributed to the dominating tonal responses within the aircraft cabin. The objective of the present effort was to improve and verify the findings of the CRA and develop and demonstrate noise control measures for single engine propeller driven General Aviation aircraft.

Unruh, James F.↗
NASA NTRS2002

General Aviation Interior Noise: Source/Path Identification - Part 1

There were two primary objectives of the research effort reported herein. The first objective was to identify and evaluate noise source/path identification technology applicable to single engine propeller driven aircraft that can be used to identify interior noise sources originating from structure-borne engine/propeller vibration, airborne propeller transmission, airborne engine exhaust noise, and engine case radiation. The approach taken to identify the contributions of each of these possible sources was first to conduct a Principal Component Analysis (PCA) of an in-flight noise and vibration database acquired on a Cessna Model 182E aircraft. The second objective was to develop and evaluate advanced technology for noise source ranking of interior panel groups such as the aircraft windshield, instrument panel, firewall, and door/window panels within the cabin of a single engine propeller driven aircraft. The technology employed was that of Acoustic Holography (AH). AH was applied to the test aircraft by acquiring a series of in-flight microphone array measurements within the aircraft cabin and correlating the measurements via PCA. The source contributions of the various panel groups leading to the array measurements were then synthesized by solving the inverse problem using the boundary element model.

Unruh, James F.↗
NASA NTRS1990

Structure-borne noise estimates for the PTA aircraft

Estimates of the level of in-flight structure-borne noise transmission in the Propfan Test Assessment Aircraft were carried out for the first three blade passage frequencies. The procedure used combined the frequency response functions of wing strain to cabin sound pressure level (SPL) response obtained during ground test with in-flight measured wing strain response data. The estimated cabin average in-flight structure-borne noise levels varied from 64 to 84 dB, with an average level of 74 dB. The estimates showed little dependence on engine/propeller power, flight altitude, or flight Mach number. In general, the bare cabin noise levels decreased with increasing propeller tone, giving rise to a plausible structure-borne noise transmission problem at the higher blade passage tones. Without knowledge of the effects of a high insertion loss side wall treatment on structure-borne noise transmission, no quantitative conclusions could be made.

Unruh, James F.↗
NASA NTRS1989

Aircraft propeller induced structure-borne noise

A laboratory-based test apparatus employing components typical of aircraft construction was developed that would allow the study of structure-borne noise transmission due to propeller induced wake/vortex excitation of in-wake structural appendages. The test apparatus was employed to evaluate several aircraft installation effects (power plant placement, engine/nacelle mass loading, and wing/fuselage attachment methods) and several structural response modifications for structure-borne noise control (the use of wing blocking mass/fuel, wing damping treaments, and tuned mechanical dampers). Most important was the development of in-flight structure-borne noise transmission detection techniques using a combination of ground-based frequency response function testing and in-flight structural response measurement. Propeller wake/vortex excitation simulation techniques for improved ground-based testing were also developed to support the in-flight structure-borne noise transmission detection development.

Unruh, James F.↗
NASA NTRS1988

Multiple input/output random vibration control system

A multi-input/output random vibration control algorithm was developed based on system identification concepts derived from random vibration spectral analysis theory. The unique features of the algorithm are: (1) the number of input excitors and the number of output control responses need not be identical; (2) the system inverse response matrix is obtained directly from the input/output spectral matrix; and (3) the system inverse response matrix is updated every control loop cycle to accommodate system amplitude nonlinearities. A laboratory demonstration case of two imputs with three outputs is presented to demonstrate the system capabilities.

Unruh, James F.↗
NASA NTRS1987

Structure-borne noise control for propeller aircraft

A laboratory test apparatus was developed which would allow the study and development of propeller wake/vortex-induced structure-borne interior noise control measures. Various methods of wing structural modification, including blocking masses, surface damping treatments, and tuned mechanical absorbers, were evaluated relative to reduced interior noise levels. Inboard wing fuel was found to act as an effective blocking mass. Wing panel add-on damping treatment in the form of a single, constrained layer was not an effective control measure, except in the area of the propeller wake. However, highly damped, tuned mechanical absorbers were found to be the most efficient structure-borne noise (SBN) control measure.

Unruh, James F.↗