Engineering topics

Urso, Justin

Publications and source records attributed to Urso, Justin.

7 records

DOE OSTI2024

DME-Propane Autoignition Measurements inside a Shock Tube

Dimethyl ether (DME) is a biofuel that has the potential to replace diesel in heavy-duty engines. A blend of propane (C3H8) and DME could reduce emissions when compared to diesel at heavy-duty compression engine-relevant conditions. Testing a potential new mixture in a compression engine requires a high-fidelity chemical kinetics model that accurately predicts autoignition delay times, which is especially necessary for a compression engine. In this work, autoignition data has been gathered at an equivalence ratio of 2.0 for pressures of 60 and 80 bar. DME and propane were combusted in synthetic air while excited hydroxyl (OH*) chemiluminescence was used to gather ignition delay times. Data was compared to recent chemical kinetic mechanisms for the two different pressures. Using the mechanism with the best fit of autoignition data, a sensitivity analysis was conducted to analyze the chemical kinetics of the DME/C3H8 combustion at elevated pressures.

Mohammed, Zuhayr Pasha↗

DOE OSTI2023

Hydrogen and Ammonia Blending With Natural Gas: Ignition Delay Times and Chemical Kinetic Model Validation at Gas Turbine Relevant Conditions

Abstract Ignition delay times from undiluted mixtures of natural gas (NG)/H2/Air and NG/NH3/Air were measured using a high-pressure shock tube at the University of Central Florida. The combustion temperatures were experimentally tested between 1000–1500 K near a constant pressure of 25 bar. As mentioned, mixtures were kept undiluted to replicate the same chemistry pathways seen in gas turbine combustion chambers. Recorded combustion pressures exceeded 200 bar due to the large energy release, hence why these were performed at the high-pressure shock tube facility. The data is compared to the predictions of the NUIGMech 1.1 mechanism for chemical kinetic model validation and refinement. An exceptional agreement was shown for stoichiometric conditions in all cases but strayed at lean and rich equivalence ratios, especially in the lower temperature regime of H2 addition and all temperature ranges of the baseline NG mixture. Hydrogen addition also decreased ignition delay times by nearly 90%, while NH3 fuel addition made no noticeable difference in ignition time. NG/NH3 exhibited similar chemistry to pure NG under the same conditions, which is shown in a sensitivity analysis. The reaction CH3 + O2 = CH3O + O is identified and suggested as a possible modification target to improve model performance. Increasing the robustness of chemical kinetic models via experimental validation will directly aid in designing next-generation combustion chambers for use in gas turbines, which in turn will greatly lower global emissions and reduce greenhouse effects.

Pierro, Michael↗

DOE OSTI2023

DME-Propane Ignition Delay Time Measurements at Mixing Controlled Compression Ignition Engine-Relevant Conditions

The blend of dimethyl ether (DME, CH 3 OCH 3 ) and propane (C 3 H 8 ) is a potentially renewable fuel mixture that has the potential to replace diesel in compression ignition engines. The combination can potentially reduce particulate and greenhouse gas emissions compared to a conventional diesel engine operating under similar conditions. However, detailed conceptual and simulation studies must be conducted before adopting a new fuel on a compression ignition engine. For these simulations, accurate chemical kinetic models are necessary. However, the validity of chemical kinetic mechanisms in the literature is unknown for mixing controlled compression ignition (MCCI) engine operating conditions. Hence, in this work, we studied the ignition of dimethyl ether (DME) and propane blends in a shock tube at MCCI engine conditions. Ignition delay time (IDT) data was collected behind the reflected shock for DME-propane mixtures for heavy-duty compression ignition (CI) engine parameters. Undiluted experiments spanning temperatures of 700 to 1100 K and pressures of 55 to 84 bar for various blends (100% CH 3 OCH 3 / 0% C 3 H 8, 100% C 3 H 8 / 0% CH 3 OCH 3 , 60% CH 3 OCH 3 / 40% C 3 H 8 ) of DME and propane were combusted in synthetic air (21% O 2 / 79% N 2 ). Some experiments were conducted at higher pressures (90-120 bar) to understand model performance at these conditions. Comparisons of IDT were made with the predictions of recent chemical kinetic mechanisms for DME-propane mixture, including the Aramco3.0, NUIG, and Dames et al. mechanisms. All mechanisms overpredicted IDT compared to experimental values. Sensitivity analysis was conducted with Dames et al. model, and critical reactions sensitive to IDT of DME-propane mixture near 100 bar are outlined.

Mohammed, Zuhayr Pasha↗

DOE OSTI2022

Experimental Ignition Delay Time Measurements and Chemical Kinetics Modeling of Hydrogen/Ammonia/Natural Gas Fuels

In recent years, hydrogen-carrying compounds have accrued interest as an alternative to traditional fossil fuels due to their function as zero-emission fuels. As such, there is interest in investigating hydrogen-carrying compounds to improve understanding of the fuels' characteristics for use in high pressure systems. In the current study, the oxidation of ammonia/natural gas/hydrogen mixtures was carried out to study carbon monoxide (CO) formation profiles as well as the ignition delay times (IDTs) behind reflected shock waves in order to refine chemical kinetic models. Experiments were carried out in the University of Central Florida's shock tube facility by utilizing chemiluminescence to obtain OH* emission and laser absorption spectroscopy to obtain CO profiles over a temperature range between 1200 K and 1800 K with an average pressure of 2.2 atm. Experimental mixtures included both neat and combination natural gas/hydrogen with ammonia addition, with all mixtures except one having an equivalence ratio of 1. Results were then compared with the GRI 3.0 mechanism, as well as the newly developed UCF 2022 mechanism utilizing chemkin-pro software. In general, both models were able to capture the trend in auto-ignition delay times and CO time histories for natural gas and ammonia mixtures. However, for ammonia–hydrogen mixtures, GRI 3.0 failed to predict ignition delay times, whereas the UCF 2022 mechanism was able to capture the IDTs within the uncertainty limits of the experiments. A sensitivity analysis was conducted for different mixtures to understand the important reactions at the experimental conditions. Lastly, a reaction pathway analysis was carried out to understand important ammonia decomposition pathways in the presence of hydrogen and natural gas.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2022

Autoignition Delay Time Measurements and Chemical Kinetic Modeling of Hydrogen/Ammonia/Natural Gas Mixtures

Abstract In recent years, hydrogen-carrying compounds have accrued interest as an alternative to traditional fossil fuels due to their function as zero-emission fuels. As such, there is interest in investigating hydrogen-carrying compounds to improve understanding of the fuels’ characteristics for use in high-pressure systems. In the current study, the oxidation of ammonia/natural gas/hydrogen mixtures was carried out to study CO formation profiles as well as the ignition delay times behind reflected shock waves in order to refine chemical kinetic models. Experiments were carried out in the University of Central Florida’s shock tube facility by utilizing chemiluminescence to obtain OH* emission and laser absorption spectroscopy to obtain CO profiles. Experimental results were then compared with the GRI 3.0 mechanism, as well as the proprietary UCF 2022 mechanism utilizing CHEMKIN-Pro software. In general, both models were able to capture the trend in autoignition delay times and CO time histories for natural gas and ammonia mixtures. However, for ammonia-hydrogen mixtures, GRI 3.0 failed to predict ignition delay times whereas the UCF 2022 mechanism was able to capture the IDTs within the uncertainty limits of the experiments. A sensitivity analysis was conducted for different mixtures to understand the important reactions at the experimental conditions. Finally, a reaction pathway analysis was carried out to understand important ammonia decomposition pathways in the presence of hydrogen and natural gas.

Baker, Jessica B.↗

DOE OSTI2022

High-Fuel Loading Ignition Delay Time Characterization of Hydrogen/Natural Gas/Ammonia at Gas Turbine-Relevant Conditions Inside a High-Pressure Shock Tube

Abstract This study explores the combustion characterization of high-fuel percentage, air-diluted mixtures of H2 mixed with natural gas (NG) as well as mixtures of H2 and NH3 at temperatures and pressures relevant to turbine operating conditions (20–30 bar, 1000–1500 K). Lower temperatures (below 1070 K) exhibit preignition characteristics due to non-homogeneity. An attempt to mitigate these occurrences at high pressures is investigated using the constrained reaction volume (CRV) stage-filling technique. Due to the need to further refine the facility CRV stage-filling uncertainty, only higher temperature data will be interpreted at this time. The test conditions in this study closely replicate the temperatures, pressures, and mixtures that would be seen in hydrogen-powered gas turbines, making it the first to explore such conditions. The experimental IDTs were compared against the current state-of-the-art chemical kinetic models for mechanism validation. The current work will advance H2-powered turbines and aims to determine the optimum molecular ratio of H2 when mixed with natural gas.

Pierro, Michael↗

DOE OSTI2020

Measurements of Density and Sound Speed in Mixtures Relevant to Supercritical CO2 Cycles

Abstract The objective of this research is to validate properties of mixtures relevant to supercritical carbon dioxide (sCO2) power cycles. Direct-fired sCO2 cycles are a promising technology for the future power generation systems. The working fluid of sCO2 cycles will be near and above critical point of CO2. One of the challenges is that the simulation of mixtures should consider real gas behavior. Expected operating conditions of Allam cycles reach up to 300 bar and 1000 °C. Characterizing the mixtures at the extreme conditions is an important issue in current researches and industrial applications. Thermophysical properties of mixtures may be beyond the valid range of the widely used database such as NIST REFPROP. Experimental data of mixture properties in the literature are limited which is necessary to develop high-fidelity design tools for sCO2 power cycles. We measured the density and sound speed of several multi-component mixtures. A temperature-controlled high-pressure test cell was used for the density measurements. Sound speed was measured by resonant frequency detection using an external speaker and a piezoelectric pressure sensor. Mixtures studied in this work include carbon dioxide, methane, oxygen, and water vapor. Properties of pure CO2 were measured to show the validity of our technique. Compositions were selected to be close to frozen mixtures at the inlet, mid-progress, and exhaust conditions of a model sCO2 combustor in the previous numerical simulation work. Corresponding reaction progress variables (RPV) were RPV = 0, 0.5, and 1. Temperature and pressure conditions of experiments are 310–450 K and 0–150 bar. In our study, density and sound speed from the NIST REFPROP database agree with experimental measurements within the range of our measurement uncertainties.

Energy & Fuels↗