Engineering topics

Valdez, James Anthony

Publications and source records attributed to Valdez, James Anthony.

17 records

DOE OSTI2024

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY24

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) project is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline collaboration to provide engineers with experience in both numerical simulations and experimental methods. This work uses and provides feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development. TRUST currently includes five testbeds and their associated engineering analysis baseline models (EABMs): 1. contact thermal conductivity, (CTC) 2. nonlinear dynamics, (ND) 3. sensors in environments for accelerometers, (SEA) 4. sensors in environments for fiber optic displacement gages, and (SEFOD) 5. sensors in environments for thermocouples (SETC). The TRUST project uses single-feature testbeds to quantify uncertainties in specific models and experiments and to identify capability development needs that can help to reduce these uncertainties. Each testbed is designed, configured, and tested in collaboration with groups with design and experimental capability: E-14 and MPA-CINT. The complementary simulations are conducted using W-13 analysis tools and stored in model repositories with plans for incremental progress toward EABM requirements. W-13 extends and exercises the testbed simulations in collaboration with experimentalists for uncertainty quantification of current and future materials, geometries, and environments. Additionally, TRUST is intended to provide engineers in W-13 and E-14 with experience in both numerical simulations and experimental methods through cross-discipline collaborations. Following the introduction to the TRUST project, the remainder of this report focuses on experimental and analytical efforts conducted in Fiscal Year (FY) 2024 relevant to the TRUST Contact Thermal Conductance (CTC) testbed.

42 ENGINEERING↗

DOE OSTI2024

Calibration and validation of the foundation for a multiphase strength model for tin

In this work, the Common Model of Multi-phase Strength and Equation of State (CMMP) model was applied to tin. Specifically, calibrations of the strength-specific elements of the CMMP foundation were developed with a combination of experiments and theory, and then the model was validated experimentally. The first element of the foundation is a multi-phase analytic treatment of the melt temperature and the shear modulus for the solid phases. These models were parameterized for each phase based on ab initio calculations using the software VASP (Vienna Ab initio Simulations Package) based on density functional theory. The shear modulus model for the ambient phase was validated with ultrasonic sound speed measurements as a function of pressure and temperature. The second element of the foundation is a viscoplastic strength model for the phase, upon which strength for inaccessible higher-pressure phases can be scaled as necessary. The stress–strain response of tin was measured at strain rates of 10 -3 to 3 x 10 3 s -1 and temperatures ranging from 87 to 373 K. The Preston–Tonks–Wallace (PTW) strength model was fit to that data using Bayesian model calibration. For validation, six forward and two reverse Taylor impact experiments were performed at different velocities to measure large plastic deformation of tin at strain rates up to ⁠10 5 s -1 . The PTW model accurately predicted the deformed shapes of the cylinders, with modest discrepancies attributed to the inability of PTW to capture the effects of twinning and dynamic recrystallization. Some material in the simulations of higher velocity Taylor cylinders reached the melting temperature, thus testing the multiphase model because of the presence of a second phase, the liquid. In simulations using a traditional modeling approach, the abrupt reduction of strength upon melt resulted in poor predictions of the deformed shape and non-physical temperatures. With CMMP, the most deformed material points evolved gradually to a mixed solid–liquid but never a fully liquid state, never fully lost strength, stayed at the melt temperature as the latent heat of fusion was absorbed, and predicted the deformed shape well.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Calibration and validation of the foundation for a multiphase strength model for tin

In this work, the Common Model of Multi-phase Strength and Equation of State (CMMP) model was applied to tin. Specifically, calibrations of the strength-specific elements of the CMMP foundation were developed with a combination of experiments and theory, and then the model was validated experimentally. The first element of the foundation is a 10 multi-phase analytic treatment of the melt temperature and the shear modulus for the solid phases. These models were parameterized for each phase based on ab initio calculations using the software VASP (Vienna Ab initio Simulations Package) based on density functional theory (DFT). The shear modulus model for the ambient β phase was validated with ultrasonic sound speed measurements as a function of pressure and temperature. The second element of the foundation is a viscoplastic strength model for the β phase, upon which strength for inaccessible higher-pressure phases can be scaled as necessary. The stress-strain response of tin was measured at strain rates of 10 -3 to 3 x 10 3 s -1 and temperatures ranging from 87 to 373 K. The Preston-Tonks-Wallace (PTW) strength model was fit to that data using Bayesian model calibration. For validation, six forward and two reverse Taylor impact experiments were performed at different velocities to measure large plastic deformation of tin at strain rates up to 10 5 s -1 . The PTW model accurately predicted the deformed shapes of the cylinders, with modest discrepancies attributed to the inability 20 of PTW to capture the effects of twinning and dynamic recrystallization. Some material in the simulations of higher velocity Taylor cylinders reached the melting temperature, thus testing the multiphase model because of the presence of a second phase, the liquid. In simulations using a traditional modeling approach, the abrupt reduction of strength upon melt resulted in poor predictions of the deformed shape and non-physical temperatures. With CMMP, the most deformed material points evolved gradually to a mixed solid-liquid but never fully liquid state, never fully lost strength, 25 stayed at the melt temperature as the latent heat of fusion was absorbed, and predicted the deformed shape well.

36 MATERIALS SCIENCE↗

DOE OSTI2023

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY23

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), test information management system (TIMS), and [WAVES] Analysis for Verified Engineering Simulation (WAVES).

42 ENGINEERING↗

DOE OSTI2023

An Investigation of Nanoindentation as Quality Control [Slides]

Nanoindentation Continuous Stiffness Measurement (CSM) mapping, and Strain Rate Jump Testing (SRJT) proved effective to highlight and visualize the extent of property differences between the samples. From the analysis, Lot A has a significant dead zone at its center, especially when compared with the cross section of Lot B. Quick identification of property issues from one of the two feed stocks, both of which fit the specification. Mechanical performance was connected to the microstructure. Thus, using the structure-property results, it is noted that the processing of Lot A may have been insufficient. Nanoindentation allows for the sampling of quality control variables such as hardness and modulus in a short time span at high resolution, which is cheaper and faster than traditional strength experiments (tension and compression tests).

36 MATERIALS SCIENCE↗

DOE OSTI2023

Analysis of Coronado State Historic Site artifacts using X-rays

Two historic-period metal artifacts were provided by the New Mexico Historic Sites to Los Alamos National Laboratory for non-destructive analysis. The artifacts were a crossbow quarrel (or bolthead) and a reliquary pendant recovered from Kuaua Pueblo (also known as the Coronado Historic Site) in Bernalillo, NM. The quarrel is a heavily patinated metal that had been flattened due to compressive forces. The pendant consisted of a metal casing that had previously surrounded two center gemstones on the front and rear face of the pendant. The gemstone in the rear setting had fractured and was displaced from the setting, leaving only a small, loose fragment within the pendant for study. The front gem appeared to be very dark, near-black in color, and the fragment of the rear gem was a bright red color. The artifacts were analyzed to ascertain their composition and glean insight into their provenance using the following X-ray techniques: X-ray computed tomography, confocal micro X-ray fluorescence, and X-ray diffraction. Infrared spectroscopy and electron microscopy were used on selected areas. Ultraviolet Raman spectra were collected on the two gems and the pendant. The metal material of the artifacts was found to be primarily composed of copper. The gems in the pendant were composed of manganese (front gem) and calcium (side gem).

36 MATERIALS SCIENCE↗

DOE OSTI2023

The effect of microstructure on the dynamic shock response of 1045 steel

Herein, the effect of microstructure on the shock response of 1045 steel is investigated via plate impact experiments and postmortem characterization. Three unique microstructures are explored: ferrite-pearlite, martensite, and ferrite with spheroidal cementite (i.e. spheroidized). Two spall recovery experiments, at approximate peak pressures of 3.2 and 3.5 GPa, are conducted to assess the Hugoniot elastic limit (HEL), spall strength, and damage morphology of the various microstructures. The ferrite-pearlite and martensite microstructures exhibit continuous yielding at both quasi-static and dynamic rates, while the spheroidized condition displays discontinuous yielding. Discontinuous yielding of the spheroidized microstructure is attributed to a combined low initial dislocation density coupled with a low dislocation nucleation rate. The spall strength of ferrite-pearlite is consistently lower than the spheroidized microstructure, attributed to elongated cementite that is more susceptible to cracking than more spherical cementite precipitates. Despite a high density of boundaries, martensite exhibits the highest spall strength. A large percentage of the boundaries within the martensite microstructure are found to be low energy (i.e. Σ3 or low angle), and are thus less susceptible to spall damage. Overall, the high spall strength of martensite is likely linked to traditional strengthening mechanisms that limit dislocation motion.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Rugged bialkali photocathodes encapsulated with graphene and thin metal film

Protection of free-electron sources has been technically challenging due to lack of materials that transmit electrons while preventing corrosive gas molecules. Two-dimensional materials uniquely possess both of required properties. Here, we report three orders of magnitude increase in active pressure and factor of two enhancement in the lifetime of high quantum efficiency (QE) bialkali photocathodes (cesium potassium antimonide (CsK 2 Sb)) by encapsulating them in graphene and thin nickel (Ni) film. The photoelectrons were extracted through the graphene protection layer in a reflection mode, and we achieved QE of ~ 0.17% at ~ 3.4 eV, 1/e lifetime of 188 h with average current of 8.6 nA under continuous illumination, and no decrease of QE at the pressure of as high as ~ 1 × 10 –3 Pa. In comparison, the QE decreased drastically at 10 –6 Pa for bare, non-protected CsK 2 Sb photocathodes and their 1/e lifetime under continuous illumination was ~ 48 h. We attributed the improvements to the gas impermeability and photoelectron transparency of graphene.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Accelerated radiation tolerance testing of Ti-based MAX phases

MAX phases have recently attracted significant attention for potential nuclear applications due to their novel properties such as unique hexagonal-compact nanolayered crystal structure, high-machinability due to lower hardness levels compared to conventional ceramics, and high-chemical inertness. In order for MAX phases to be used in nuclear reactors, two aspects deserve detailed investigations: (i) their phase stability at high-temperatures and (ii) microstructural defect formation and recovery induced by energetic particle irradiation. To date, degradation mechanisms of MAX phases at high-temperatures and following irradiation are largely unexplored fields of research. This work focuses on the evaluation of two Ti-based MAX phases – Ti 2 AlC and Ti 3 SiC 2 – within the context of extreme environments. To accomplish this, a one-of-a-kind comparison between neutron irradiations, performed over a decade of research at the High Flux Isotope Reactor (HFIR), and heavy-ion irradiations, carried out in situ in a Transmission Electron Microscope (TEM) at the MIAMI-2 facility, has been conducted. The results show Ti-based MAX phases are prone to accelerated decomposition under the conditions investigated. This questions the hypothesis that MAX phases exhibit high phase stability, especially when used in future nuclear energy systems where energetic particle irradiation is a dominating degradation mechanism.

36 MATERIALS SCIENCE↗

DOE OSTI2022

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY2022

42 ENGINEERING↗

DOE OSTI2022

Compositional screening of Ce-doped (Gd,Lu,Y) 3 (Al,Ga) 5 O 12 ceramics prepared by quenching from melt and their luminescence properties

Quenching from the melt using an Optical Floating Zone furnace was investigated as a possible high-throughput preparation method in order to screen novel scintillating materials. To validate this method, polycrystalline rare-earth aluminum garnets and yttrium gallium aluminum garnets were synthesized and characterized by X-ray diffraction, photoluminescence and radioluminescence emission spectra as well as radioluminescence imaging and compared to the previously reported properties of those materials. In order to achieve rapid, but quantitative comparison of the materials, pellets fabricated from the synthesized powders were sintered; two different sintering conditions were investigated and compared. Therefore, a simplistic energy deposition and light absorption model for brightness of opaque samples under X-ray irradiation was developed to estimate the relative scintillation efficiency of the materials. Based on the results, Y 3 Al 5 O 12 , LuY 2 Al 5 O 12 and GdY 2 Al 5 O 12 seem to have the highest scintillation efficiency among the prepared samples.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The influence of pearlite fraction on the shock properties of ferrite–pearlite steel microstructures: Insight into the effect of second-phase particles

Here, the goal of this work is to investigate the effect of varying phase fractions on the overall spall strength and damage behavior of a material. Specifically, two plain carbon, ferrite–pearlite steels (1045 and A283) were subjected to spall recovery experiments to investigate the effect of pearlite fraction on spall strength and total damage. The A283 (20% pearlite) alloy exhibited a higher Hugoniot elastic limit and spall strength compared with 1045 (60% pearlite). Discontinuous and continuous yielding behaviors were observed at quasi-static and dynamic rates for A283 and 1045, respectively. The yielding behavior was connected to pearlite fraction and the prevalence of dislocation-emitting, ferrite/cementite interfaces. Postmortem characterization revealed cementite lamellae cracking within pearlite of 1045, suggesting that pearlite reduces spall strength by providing low-energy damage nucleation sites. The rate of damage growth and coalescence was similar between the two alloys; however, 1045 exhibited more continuous cracks than A283, which exhibited a greater prevalence of discrete voids.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Microstructural dependence of defect formation in iron-oxide thin films

In this report passivating iron-oxide films are grown atop iron films simulating the corrosion process in a nuclear reactor environment. Two oxide films grown via physical vapor deposition at 600 °C and room temperature exhibited dense-epitactic and columnar-polycrystalline, microstructures respectively. A third oxide film grown in open air at 600 °C exhibited an eqiuaxed, porous morphology. Cubic maghemite and magnetite phases in each oxide film were identified via grazing incidence X-ray diffraction. Positron annihilation spectroscopy was used to characterize point defects and measure their depth and size distributions in each oxide layer and showed a range of average positron lifetimes from 0.23 ns in the high temperature, vapor deposited film, 0.35 ns in the room temperature-grown film, and 0.31 ns in the thermally grown oxide. These data indicate that the film morphology, which varies greatly in these films, leads to very different defect content. Finally, four-dimensional scanning transmission electron microscopy was used to measure the internal stress of each film and was correlated to the strain state presented in the X-ray diffraction spectra. The defect formation in each film is reasoned through using a thin film growth model.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The influence of the processing parameters on the reactive flash sintering of ZrO 2 -CeO 2

Reactive flash sintering (RFS) is a method that was recently developed to produce dense single-phase bulk ceramic parts through solid-state reactions in a single-step that only takes a few minutes. The influence of the RFS parameters on the phase purity of a simple mixed oxide, (Zr 0.8 ,Ce 0.2 )O 2 , was investigated. Parameters such as furnace temperature, furnace atmosphere, electric current density, and alternating current (AC) or direct current (DC) were examined. It was found that (Zr 0.8 ,Ce 0.2 )O 2 pellets with high densities, above 90% of its theoretical density, can be produced by RFS in a few minutes when RFS occurs under oxidizing atmospheres, AC fields with current densities of 100 mA·mm –2 , and at a furnace temperature of 1200°C. Reducing conditions such as Ar-H 2 atmosphere and DC fields, low furnace temperatures, and low current densities resulted in phase impurities and poor reactions between the ZrO 2 and the CeO 2 powders. These results show that RFS is a useful method to produce mixed oxides, but it is very sensitive to the processing parameters. This is the first time that the influence of most of the RFS processing parameters has been studied systematically. Thus, the present work aims to provide guidelines on selecting the right processing parameters when exploring RFS.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Experimental Procedure and Results for Contact Thermal Conductance Measurements performed during FY 2021

Weapons Test Engineering groups at LANL are responsible for testing and simulating weapon assemblies and subassemblies in support of qualification and certification of nuclear weapon systems. The complex nature of the assemblies themselves coupled with the loading environments, gives rise to low confidence and high uncertainties in the interpretation of both experimental and simulated results. In an effort to reduce these uncertainties, a project was started at LANL to perform focused and systematic experiments combined with simulations to increase confidence in both arenas. A key goal of the work performed under the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests TRUST program, focuses on identifying and minimizing sources of uncertainty associated with experimental and computational techniques. Specifically, with the above as motivation, a measurement procedure was developed by MST-8 to perform thermal conductivity measurements on cylinders of both similar and dissimilar metallic systems as a function of loading conditions and varying material interface morphologies between these components.

36 MATERIALS SCIENCE↗

DOE OSTI2020

In-situ re-crystallization of heavily-irradiated Gd 2 Ti 2 O 7

Gadolinium titanate (Gd 2 Ti 2 O 7 , or GTO) and other lanthanide pyrochlores are interesting candidates for actinide waste disposal and fast ion conduction because the relevant material properties are intimately dependent on local cation structure. Therefore, a deep understanding of the kinetics associated with cation ordering and disordering is required if such material properties are to be tuned for specific device designs. To this end, single crystals of GTO were irradiated with 190 keV helium ions to a total fluence of 1 × 10 17 ions/cm 2 , amorphizing the sample surface to a depth of ~1 μm and resulting in significant He bubble accumulation. FIB lamellae lifted out from the irradiated sections were examined during heat treatment in the (scanning) transmission electron microscope. Two distinct stages of the re-crystallization of the amorphized material were observed. The material near the end of the ions’ range transformed first and with the same orientation as the pristine material. This was due to the close proximity of the pristine material and the presence of small defect fluorite seeds, but the propagation of this growth front was frustrated by the large pores (formerly bubbles) in the He accumulation layer. This was followed by heterogeneous nucleation of new crystallites at random orientations at the top of the He accumulation layer, which is attributed to the high surface area associated with the many small He bubbles in that region. Finally, it is inferred that the kinetics of grain growth in this material are significantly faster than the kinetics of grain nucleation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Proton irradiation and characterization of additively manufactured 304L stainless steels

Irradiations were performed with 1.5 MeV protons to 0.6 dpa at 40–150 °C on additively manufactured (AM) 304L stainless steel and the changes in microstructure and mechanical behavior after irradiation were compared to wrought 304L stainless steel. Interestingly, all microstructural and hardness results after irradiation suggest the samples evolve toward a similar state, despite significant differences in the unirradiated microstructures and hardness values. A TEM and nanoindentation-based investigation of before and after proton irradiation at 40–150 °C is presented. Results are interpreted in terms of initial dislocation content, dislocation structures, and microstructural and chemical homogeneity.

36 MATERIALS SCIENCE↗