Search NASA⌕ Search

Engineering topics

Valente-Feliciano, Anne-Marie

Publications and source records attributed to Valente-Feliciano, Anne-Marie.

At least 19 records

Properties of Nb x Ti (1–x) N thin films deposited on 300 mm silicon wafers for upscaling superconducting digital circuits

Scaling superconducting digital circuits requires fundamental changes in the current material set and fabrication process. The transition to 300 mm wafers and the implementation of advanced lithography are instrumental in facilitating mature CMOS processes, ensuring uniformity, and optimizing the yield. Here, this study explores the properties of Nb x Ti (1–x) N films fabricated by magnetron DC sputtering on 300 mm Si wafers. As a promising alternative to traditional Nb in device manufacturing, Nb x Ti (1–x) N offers numerous advantages, including enhanced stability and scalability to smaller dimensions, in both processing and design. As a ternary material, Nb x Ti (1–x) N allows engineering material parameters by changing deposition conditions. The engineered properties can be used to modulate device parameters through the stack and mitigate failure modes. We report characterization of Nb x Ti (1–x) N films at less than 2% thickness variability, 2.4% T c variability and 3% composition variability. Film resistivity (140–375 Ωcm) shows a strong correlation with the film oxygen content, while the critical temperature T c (4.6 K–14.1 K) is strongly affected by film stoichiometry and its microstructure has only a moderate effect on modifying T c . Our results offer insights about the interplay between film stoichiometry, film microstructure and critical temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Identifying Downtime Sources in CEBAF SRF Linac Systems for Improving Its Reliability

In this work, we will present some recent analysis of the reliability statistics of the CEBAF SRF linac systems. Based on the data collected by the existing Down Time Manager (DTM), the year-to-year downtime evolution trend of linac zones over the six-year period from FY18 to FY23 is established. An in-depth downtime analysis at a resolution beyond the linac zone level was carried out by introducing a new system hierarchy, consisting of the SRF linac sub-systems and components. This new paradigm was implemented in a pilot downtime study over the two-month period of CEBAF operation from 9/13/23 to 11/13/23, enabling localization of the responsible sub-systems (SRF, HPRF, LLRF, Beamline vacuum, Cryogenics, etc.) and hardware components (cavity, tuner, RF coupler, etc.) in the CEBAF SRF linac systems. Pinpointing downtime sources over long operation periods at the sub-systems and component levels holds the key to improving the CEBAF SRF systems reliability. It also helps identify areas of SRF technology development needed by future high-power high-reliability CW SRF linacs.

Hryhorenko, Oleksandr↗

High power pulse systems for surface processing

A high-power pulsed surface processing system includes insulated-gate bipolar transistors (IGBT) to replicate desirable pulse structures with high precision, at low cost, and with high reliability within a single system. The pulsed surface processing system includes a power supply, an anode and a cathode, a dual gate driver supplying power to one or more IGBT gates, and one or more capacitor banks. Pulse formation software controls the timing and duration of electrical pulses to the electrodes. A freewheeling diode protects the system from an abrupt reduction of current in the circuit. The high-power pulsed surface processing system may be used to control versatile and complex pulse structures while with precise control of instantaneous pulse powers, pulse timing, and process control. The inclusion of dual gate drivers also offers the ability for multiple pulsers to be created and “slaved” together for a wide variety of custom processes.

Tian, Hui↗

Evidence for current suppression in superconductor–superconductor bilayers

Superconducting radio frequency (SRF) cavities, which are critical components in many particle accelerators, need to be operated in the Meissner state to avoid strong dissipation from magnetic vortices. For a defect-free superconductor, the maximum attainable magnetic field for operation is set by the superheating field, B sh , which directly depends on the surface current. In heterostructures composed of different superconductors, the current in each layer depends not only on the properties of the individual material, but also on the electromagnetic response of the adjacent layers through boundary conditions at the interfaces. Three prototypical bilayers [Nb 1–x Ti x N (50 nm)/Nb, Nb 1–x Ti x N (80 nm)/Nb, and, Nb 1–x Ti x N (160 nm)/Nb] are investigated here by depth-resolved measurements of their Meissner screening profiles using low energy muon spin rotation (LE-µSR). From fits to a model based on London theory (with appropriate boundary and continuity conditions), a magnetic penetration depth for the thin Nb 1–x Ti x N layers of λ Nb 1–x Ti x N = 182.5(31) nm is found, in good agreement with literature values for the bulk alloy. Using the measured λ Nb 1–x Ti x N , the maximum vortex-free field, B max , of the superconductor-superconductor (SS) bilayer structure was estimated to be 610(40) mT. The strong suppression of the surface current in the Nb 1–x Ti x N layer suggests an optimal thickness of ~ 1.4λ Nb 1–x Ti x N = 261(14) nm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Commissioning of a two-target DC cylindrical magnetron sputter coater for depositing Nb 3 Sn film on Nb superconducting radiofrequency cavities

A DC cylindrical magnetron sputter coater was commissioned and used to coat Nb 2.6 GHz superconducting radiofrequency (SRF) cavity with Nb 3 Sn. The sputter coater has two identical cylindrical magnetrons that can move, with a controlled speed, along the axis of the SRF cavity to coat the inside surface of the cavity. The design of the sputter coater is discussed, along with its performance. Initially, a sample holder that allows coating on flat substrates at positions similar to the equator and beam tubes of a 2.6 GHz SRF cavity was used to test conditions for fabricating Nb 3 Sn layers. Multilayers of Nb and Sn were sequentially sputtered on flat Nb and sapphire substrates mounted on the equivalent positions of the cavity's beam tubes and the equator using the two identical cylindrical magnetrons. Then, the Nb/Sn multilayers were annealed at 950 °C for 3 h. Here, the ~1.2 μm thick Nb 3 Sn film did not show any other Nb–Sn compounds and had a superconducting transition temperature of 17.61–17.76 K. The 2.6 GHz SRF cavity was coated using similar conditions as flat samples. Cryogenic RF testing of the Nb 3 Sn-coated cavity demonstrated a quality factor of 3.2 × 10 8 at an accelerating gradient of 5 MV/m at 4.4 K.

43 PARTICLE ACCELERATORS↗

Nb₃Sn Coating of a 2.6 GHz SRF Cavity by Sputter Deposition Technique

Nb₃Sn is of interest as a coating for SRF cavities due to its higher transition temperature Tc ~18.3 K and superheating field Hsh ~400 mT, both are twice that of Nb. Nb₃Sn coated cavities can achieve high-quality factors at 4 K and can replace the bulk Nb cavities operated at 2 K. A cylindrical magnetron sputtering system was built, commissioned, and used to deposit Nb₃Sn on the inner surface of a 2.6 GHz single-cell Nb cavity. With two identical cylindrical magnetrons, this system can coat a cavity with high symmetry and uniform thickness. Using Nb-Sn multilayer sequential sputtering followed by annealing at 950°C for 3 hours, polycrystalline Nb₃Sn films were first deposited at the equivalent positions of the cavity’s beam tubes and equator. The film’s composition, crystal structure, and morphology were characterized by energy dispersive spectroscopy, X-ray diffraction, and atomic force microscopy. The Tc of the films was measured by the four-point probe method and was 17.61 to 17.76 K. Based on these studies, ~1.2 micron thick Nb₃Sn was deposited inside a 2.6 GHz Nb cavity. We will discuss first results from samples and cavity coatings, and the status of the coating system.

43 PARTICLE ACCELERATORS↗

Cylindrical Magnetron Development for Nb3sn Deposition via Magnetron Sputtering

Due to its better superconducting properties (critical temperature Tc~ 18.3 K, superheating field Hsh~ 400 mT), Nb₃Sn is considered as a potential alternative to niobium (Tc~ 9.25 K, Hsh~ 200 mT) for superconducting radiofrequency (SRF) cavities for particle acceleration. Magnetron sputtering is an effective method to produce superconducting Nb₃Sn films. We deposited superconducting Nb₃Sn films on samples with magnetron sputtering using co-sputtering, sequential sputtering, and sputtering from a stoichiometric target. Nb₃Sn films produced by magnetron sputtering in our previous experiments have achieved DC superconducting critical temperature up to 17.93 K and RF superconducting transition at 17.2 K. A magnetron sputtering system with two identical cylindrical cathodes that can be used to sputter Nb₃Sn films on cavities has been designed and is under development now. We report on the design and the current progress on the development of the system.

43 PARTICLE ACCELERATORS↗

Effect of metamaterial engineering on the superconductive properties of ultrathin layers of NbTiN

The electronic transport and optical properties of high quality multilayers of NbTiN/AlN with ultrathin NbTiN layers were characterized. The anisotropy of the dielectric function of the multilayers confirmed their hyperbolic metamaterial properties. Here, the superconductive transition temperature, T c , of these engineered superconductors was enhanced up to 32% compared to the T c of a single ultrathin NbTiN layer while the resistivity per NbTiN layer remained unchanged. We have demonstrated that this T c increase can be attributed to enhanced electron–electron interaction in superconducting hyperbolic metamaterials. The measured critical fields are high and have an anomalous temperature dependence on the direction perpendicular to the magnetic field. These results demonstrate that the metamaterial engineering approach can be used to enhance H c2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigations Towards Ultra-Low Cost Nb 3 Sn SRF Fabrication via Melt Casted Bronze Route Processing

Here, a novel approach to fabricating Nb 3 Sn SRF cavities and other RF components using an ultra-low-cost melt casting fabrication process has been investigated. This simple, low cost melt casting technique has the potential to be used to fabricate nearly any superconducting Nb3Sn structure using either the Bronze Route (BR), Internal Tin (IT), External Tin (ET) processes as well as normal conducting pure copper (Cu) cavities. Most of the heat treated samples that were examined using SEM/EDX seemed to show a reasonable correlation of T c onset and transition width (ΔT c ) of the ingots initial/starting Sn content to the desired stoichiometric Nb 3 Sn phase, where the lower starting Sn content coupons resulted in lower T c 's with broader transition widths and the higher starting Sn coupons resulted in higher T c 's with narrower ΔT c ’s. The best samples had T c onsets ~17-18 K and ΔT c 's < 2 K. Two samples were further tested for RF surface resistance (R s ) and Quality Factor (Q) at JLAB. Here, these RF measurements were performed at 7.4 GHz using a calorimetric technique and showed two transitions, one at ~ 8 K and another at ~ 14 K; values of R s were at least two orders of magnitude higher than similar high quality Nb 3 Sn films directly deposited substrates by JLAB and with another superconducting transition close to the superconducting transition temperature of niobium. Substantial improvements in the processing variables ranging from higher quality of the initial ingots with higher Sn content, to better electropolishing and reaction heat treatment regimens will be necessary to realize improved RF performance metrics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Progress with Nb Hipims Films on 1.3 GHz Cu Cavities

In recent years, efforts have been invested to leverage the different processes involved in energetic condensation to tailor Nb film growth in sequential steps. The resulting Nb/Cu films display high quality material properties and show promise of high RF performance. The lessons learned are now applied to 1.3 GHz Nb on Cu cavity deposition via high power impulse magnetron sputtering (HiPIMS). RF performance is measured at different temperatures. Particular attention is given to the effect of cooldown and sensitivity to external applied magnetic fields. The results are evaluated in light of the Nb film material and superconducting properties measured with various microscopy and magnetometry techniques in order to better understand the contributing factors to the residual and flux induced surface resistances. This contribution presents the insights gained in exploiting energetic condensation as a path towards RF Q-slope mitigation for Nb/Cu films, correlating film material characteristics with RF performance.

Burton, Matthew C.↗

Automation of particulate characterization

Foreign particles residing on the field carrying surface of accelerator cavities are a known mechanism for field emission. Developing the methods and tools for collecting and characterizing particles found in an accelerator enables process development towards field emission free SRF cavities. Methods are presented for sampling assemblies, components, processes, and environmental conditions utilizing forensic techniques with specialized tooling. Sampling activities to date have produced an inventory of over 850 GSR spindles. Traditional SEM + EDS analysis of this volume of spindles is challenged by labor investment, spindle sampling methods, and the subsequent data pipeline which ultimately results in a statically inadequate dataset for any particulate distribution characterization. A complete systematic analysis of the spindles is enabled by third party software controlling SEM automation for EDS data acquisition. Details of spindle creation, collection equipment, component sampling, automating particle assessment, and data analysis used to characterize samples from beamline elements in CEBAF are presented.

Spradlin, Josh↗

NB film engineering with energetic condensation for tailored RF behavior

The different processes involved in energetic condensation are exploited in ECR (electron cyclotron resonance) generated plasma deposition and HiPIMS to tailor SRF film growth in sequential steps. The resulting Nb/Cu films display high quality material and show promise of high RF performance. The residual and flux induced surface resistance contributing factors are investigated with RF measurements at different temperatures and frequencies coupled with film material and superconducting properties characterization with various microscopy and magnetometry techniques. Results show that the manipulation of the interface, film nucleation and growth allows to tailor fundamental properties of the material to minimize surface resistance and field dependent losses.

Valente-Feliciano, Anne-Marie↗

RF Results of Nb Coated SRF Accelerator Cavities via HiPIMS

Bulk Niobium (Nb) SRF (superconducting radio frequency) cavities are currently the preferred method for acceleration of charged particles at accelerator facilities around the world. However, bulk Nb cavities have poor thermal conductance and impose material and design restrictions on other components of a particle accelerator. Since the SRF phenomena occurs within a shallow depth of 40 nm (for Nb), a proposed solution to this problem has been to deposit a superconducting Nb thin film on the interior of a cavity made of a suitable alternative material such as copper or aluminum. While this approach has been attempted in the past using DC magnetron sputtering (DCMS), such cavities have never performed at the bulk Nb level. However, new energetic condensation techniques for film deposition offer the opportunity to create suitably thick Nb films with improved density, microstructure and adhesion compared to traditional DCMS. One such technique that has been developed somewhat recently is ?High Power Impulse Magnetron Sputtering? (HiPIMS). Here we report early results from various thin film coatings carried out on 1.3 GHz Cu cavities, a 1.5 GHz Nb cavity, and small Cu coupon samples coated at Jefferson Lab using HiPIMS.

Burton, Matthew Creed↗

An Innovative Nb3Sn Film Approach and Its Potential for SRF Applications

A novel electro-chemical technique to produce Nb3Sn films on Nb substrates was developed and optimized at Fermilab. The Nb3Sn phase is obtained in a two-electrode cell, by electrodeposition from aqueous solutions of Sn layers and Cu intermediate layers onto Nb substrates. Subsequent thermal treatments in inert atmosphere are realized at a maximum temperature of 700°C to obtain the Nb3Sn superconducting phase. Several superconduct-ing Nb3Sn films were obtained on Nb substrates by study-ing and optimizing most parameters of the electro-plating process. Samples were characterized at Fermilab, NIMS, KEK and JLAB, including EPMA analyses, DC and in-ductive tests of critical temperature Tc0, and lower critical field Hc1(4.2 K) by SQUID. In parallel to sample devel-opment and fabrication at FNAL, at JLAB and KEK effort was put into etching and electro-polishing techniques adequate to remove the Cu and bronze phases from the samples’ outer surface. This is necessary prior to meas-urements at JLAB of the surface impedance of flat sam-ples in a setup that make use of an RF host cavity.

Barzi, E. Z.↗

Effect of self-bias on cylindrical capacitive discharge for processing of inner walls of tubular structures—Case of SRF cavities

Cylindrical capacitive discharge is a convenient medium for generating reactive ions to process inner walls superconductive radio-frequency (SRF) cavities. These cavities, used in particle accelerators, present a three-dimensional structure made of bulk Niobium, with axial cylindrical symmetry. Manufactured cavity walls are covered with Niobium oxides and scattered particulates, which must be removed for desired SRF performance. Cylindrical capacitive discharge in a mixture of Ar and Cl 2 is a sole and natural non-wet acid choice to purify the inner surfaces of SRF cavities by reactive ion etching. Coaxial cylindrical discharge is generated between a powered inner electrode and the grounded outer electrode, which is the cavity wall to be etched. Plasma sheath voltages were tailored to process the outer wall by providing an additional dc current to the inner electrode with the help of an external compensating dc power supply and corrugated design of the inner electrode. The dc bias potential difference is established between two electrodes to make the set-up favorable for SRF wall processing. To establish guidelines for reversing the asymmetry and establishing the optimal sheath voltage at the cavity wall, the dc self-bias potential and dc current dependence on process parameters, such as gas pressure, rf power and chlorine content in the Ar/Cl 2 gas mixture was measured. In conclusion, the process is potentially applicable to all concave metallic surfaces.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Surface Characterization of NbTiN Films for Accelerator Applications

The development of next-generation SRF cavities requires the deployment of innovative material solutions with RF performance beyond bulk Nb. Theoretical interest has stimulated efforts to grow and characterize thin multi-layer superconductor/insulator/superconductor (SIS) structures for their potential capability of supporting otherwise inaccessible surface magnetic fields in SRF cavities *. The ternary B1-compound NbTiN is among the candidate superconducting materials for SIS structures. Single crystal NbTiN films with thicknesses below 15 nm are also of interest for the development of high resolution, high sensitivity (SNSPD) detectors for particle physics application. Using DC reactive magnetron sputtering, NbTiN can be deposited with nominal superconducting parameters. This contribution presents the on-going material surface and superconducting properties characterization in order to optimize the NbTiN films for each application.

Beverstock, David R.↗