Search NASA⌕ Search

Engineering topics

Van Rooyen, Isabella J

Publications and source records attributed to Van Rooyen, Isabella J.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

EPMA-Based Mass Balance Method for Quantitative Fission Product Distribution Comparison between TRISO Particles

Two irradiated AGR-2 TRISO particles were chosen to demonstrate a recently developed mass balance technique in which EPMA-generated concentration data was used to determine fission product mass on a layer-by-layer basis in TRISO particles. EPMA-calculated fission product masses for most fission products in the two particles were within +/- 20% of their ORIGEN-modelled masses. Results show that Sr, Ba, and Eu accumulate preferentially in the carbon-rich kernel periphery on the particles’ side that lacks a gap between the buffer and IPyC. In addition, the more mobile elements--Cs, Sr, and Pd, accumulate in greater quantity in the outer layers of particle AGR2-223-RS34 compared to particle AGR2-223-RS06, which has relatively more of those elements’ mass located in the kernel and kernel periphery, suggesting enhanced fission product transport in particle AGR2-223-RS34. This model can be used better understand and test fission product transport in TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural and Micro-Chemical Evolutions in the Irradiated UCO Fuel Kernels of AGR-1 and AGR-2 TRISO Fuel Particles

AGR-1 and AGR-2 TRISO fuel particles were fabricated with slightly different fuel kernel chemical compositions, modified fabrication processes, different fuel kernel diameters, and changed 235U enrichments. To correlate those differences with the fuel kernel responses to neutron irradiations in terms of irradiated fuel microstructure, fission products chemical and physical states, and fission gas bubble evolutions, extensive microstructural and analytical characterizations were conducted. The studies used a state of art transmission electron microscopy (TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) of four silicon solid-state detectors which have super sensitivity and fast speed. The TEM specimens were prepared from selected AGR-1 and AGR-2 irradiated fuel kernels exposed to safety testing after irradiation. The particles were chosen to represent a representative irradiation conditions with a fuel burnup within the range from 10.8 to 18.6% FIMA, and the time-average volume-average temperatures vary from 1070 to 1287°C. The 235U enrichment was 19.74 wt.% for the AGR1 fuel kernels and 14.03 wt.% for the AGR-2 fuel kernels. The TEM results show that there were significant microstructural reconstructions in the irradiated fuel kernels for both the AGR-1 and AGR-2 fuels. There are four major phases including fuel matrix of UO2 and UC, U2RuC2, and UMoC2 in the irradiated AGR2 fuel kernel. Zr and Nb form solid solution in the UC phase. UMoC2 phase often shows a detectable concentration of Tc. Pd was found to mainly locate in the buffer layer or to be associated with fission gas bubble within the UMoC2 phase. The EDS maps qualitatively show that the rare-earth fission products (Nb, et al.) preferentially reside in the UO2 phase. In contrast, in the irradiated AGR1 fuel kernel, no U2RuC2 or UMoC2 precipitates were positively identified. Instead, there is a high number of rod-shape precipitates enriched with Ru, Tc, Rh, and Pd observed in the fuel kernel center and edge zone. The difference of microstructural and micro-chemical evolutions in irradiated fuel kernels between the AGR-1 and AGR-2 TRISO fuel particle may result from a combined factor of irradiation temperature, fuel geometry and chemical composition. However, the irradiation temperature probably play a more deterministic role. Limited electron energy loss spectroscopy (EELS) characterizations on the AGR2 fuel kernel show that there is nearly no carbon in the UO2 phase while a small fraction of oxygen was detected in the UC/UMoC2 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Micro- and Nano-techniques for the Study of Fission Product Precipitation in SiC Layer

The complexity of fission product distribution and composition within the SiC layer of tristructural isotropic (TRISO) coated particles, irradiation effects on the SiC structure as well as the variable nature of metallic fission product release, has led to the exploration of multiple micro- and nano-characterization techniques. The fine scale of the fission product precipitates necessitates unique learnings and application of electron microscopic techniques with irradiated fuel during the Advanced Gas Reactor (AGR)-1 experiment analysis. A summarized discussion on the specific advanced techniques with associated method development for TRISO coated particles is provided followed by the down selected techniques currently considered to provide the highest impact. Techniques considered are electron probe micro-analyzer (EPMA), scanning transmission electron microscopy (STEM), and Precession electron diffraction (PED). SiC grain boundary characteristics are evaluated due to the mobility of specific fission products through grain boundaries. PED was performed for understanding the role of grain boundary character on fission product transport. One set of comparative analyses between AGR-1 and AGR-2 particles leads to a finding that the AGR-1, high-Ag-retention particle, had statistically more coincidence site lattice (CSL)-related grain boundaries (but fewer low-angle grain boundaries), compared to the AGR-2 particle. This implies that CSL-related grain boundaries may have a direct influence on Ag retention. However, precipitates were found on a relatively small fraction of CSL-related grain boundaries in both particles. In another set of comparison between AGR-1 and AGR-2 particles that were subjected to safety testing, there is significant differences in average SiC grain boundary distributions, but the fission product distributions on these grain boundaries are very similar.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Advanced Microscopy Report on UCO Fuel Kernels from Selected AGR-1 and AGR-2 Experiments

A variety of neutron irradiation experiments were completed at Idaho National Laboratory (INL) on tristructural isotropic (TRISO) coated particles contained in a graphitic matrix as part of the Advanced Gas Reactor (AGR) fuel development and qualification program. Although the initial advanced microscopy and microanalysis studies on AGR-1 particles focused predominantly on the SiC layer?s role as the main fission-product containment, studies were further expanded to evaluate UCO kernels of selected AGR-1 and AGR-2 coated particles. Fuel kernels tested in the AGR-1 and AGR-2 experiments is composed of a mixture of UO2 and UC, with a nominal as-fabricated stoichiometry of UO1.37 C0.35 and UO1.43 C0.39, respectively. These as-fabricated kernel-stoichiometry values are determined at the completion of kernel fabrication and do not account for any changes that will occur during the subsequent coating and compacting processes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Experimental Fabrication of Porous Additive Manufactured Material

Nuclear industries can benefit from materials that can perform well mechanically and thermally in high temperature and corrosion environments. Functionally graded materials (FGM) are materials manufactured with complex spatial, structural, and chemical compositions, creating components predesigned with tailored microstructural and mechanical properties. Porosity-graded FGMs are designed to introduce pores into a component’s structure as a mechanism to increase bulk or surface material performance, such as stress accommodation and negative thermal conductivity. Additive manufacturing (AM) techniques such as laser energy net shape (LENS) and wire arc additive manufacturing (WAAM), excel in high energy density, point-to-point metal deposition, and present in combination with other combinatorial approaches, exciting methods to manufacture porous FGM components. This project is also examining plasma jet printing as another means for method evaluations for smaller scale graded components. This study explores AM FGM process parameters and combinatorial fabrication methodologies for stainless steel components functionally graded in porosity levels. Preliminary characterization results are provided to attest the feasibility of the combinational fabrication techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Numerical study to predict the effect of surface roughness on the thermal and hydraulic performance of additively manufactured heat exchangers

Heat exchangers are used in many industries to transfer thermal energy between two or more objects with an associated thermal and hydraulic performance indicated by thermal effectiveness and pressure drop respectively. Many investigations have aimed to enhance the thermal effectiveness of heat exchangers by introducing turbulent flow inducers that increase the heat transfer rate at the expense of increasing pressure drop. Flow inducers like surface roughness can be controlled with advanced manufacturing methods like additive manufacturing for heat exchanger production. Selecting and manufacturing an optimal surface roughness for heat exchangers requires a more comprehensive approach that accounts for the surface roughness effect on the thermal and hydraulic performance of a sample. Since fabricating samples with additive manufacturing to a desired surface roughness can be an extensive experimental process, this study will fundamentally investigate the effect of surface roughness on the thermal and velocity boundary layers for various surface roughness profiles with physics-based computational modeling. To accurately model the surface roughness effect on thermohydraulic performance, correlations like roughness ratio, friction factor, and Nusselt number are investigated. This study expects to indicate correlations for different flow regimes which can successfully predict the effect of surface roughness on thermohydraulic performance. Results generated from modeling surface roughness effect with unique correlations are then compared to experimental data obtained from literature for validation. The results of this study will provide insight to understand the thermal fluid physics associated with surface roughness and design guidelines for heat exchangers produced with additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design, Manufacturing and Performance Considerations in Reactor System, Components and Materials

Idaho National Laboratory (INL) is the national and global leader of the Department of Energy (DOE) ’s nuclear energy research, development, and demonstration programs. Developing critical design criteria of new advanced reactor systems, components and materials requires an understanding of fabrication and the irradiation environment during normal operating and accident conditions. Next generation researchers and designers, are, therefore challenged not only by demands for ever improved performance but must also work to shorten the development and commercialization lifecycle for new nuclear reactors and systems to remain competitive. This provides unique and exciting opportunities for all contributors to this field of study. This presentation will offer a strategic overview of the competitively funded R&D awards by the Advanced Methods for Manufacturing (AMM) program of the DOE’s office of Nuclear Energy (NE). This program conducts research and development (R&D) to accelerate innovations by reducing the cost and schedule of constructing new nuclear plants and to make fabrication of nuclear power plant components faster, cheaper, and more reliable. By evaluating state-of-the-art practices found in other large manufacturing industries, the nuclear community has identified six major areas of innovation to reach the objectives of this DOE-NE program. Additionally, typical research case studies performed at INL, will be presented, showing the vast variety of opportunities for which, the next generation of researchers can seek solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Understanding TRISO Coated Particle Neutron Irradiation Behavior:Evolution of Advanced Micro Analysis and Electron Microscopy Approaches

Objectives and motivation• Provide data for fuel qualification in support of reactor licensing• Establish a domestic commercial TRISO fuel fabrication capability Approach • Focus is on developing and testing UCO TRISO fuel –Develop fuel fabrication and QC measurement methods, first at lab scale and then at industrial scale –Perform irradiation testingover a range of conditions (burnup, temperature, fast neutron fluence) –Perform post-irradiation examination and safety testingto demonstrate and understand performance during irradiation and during accident conditions –Develop fuel performance modelsto better predict fuel behavior –Perform fission product transport experiments to improve understanding and refine models of fission product transport

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Electron Microscopic Examination of an Irradiated TRISO Coated Particle of AGR-2 Experiment: AGR2-222-RS019

The transmission electron microscopic (TEM) examination of an irradiated tristructural isotropic (TRISO) coated particle from advanced gas reactor (AGR) 2 fuel Compact 2-2-2 is presented in this report. Compact 2-2-2 refers to the compact in Capsule 2 at Level 2 of Stack 2. The examination on AGR2 222 RS019 is focused on the interface between the silicon carbide (SiC) to inner pyrolytic carbon (IPyC) layer, central part of SiC, and the interface between SiC and outer pyrolytic carbon layer. The SiC grain boundary distribution and associated fission product precipitates were characterized by scanning transmission electron microscopy (STEM) energy dispersive spectroscopy (EDS), and precession electron diffraction (PED) in the transmission electron microscope. Two separate locations on SiC layer were selected for on the basis of the intact of the buffer layer in the irradiated TRISO particle. The key observation in this particle is that the compositional nature of grain boundary precipitates is more complex near IPyC/SiC layer where Pd, Pd-Ag, Pd-U containing precipitates can be observed. However, the compositions of precipitate towards outer most region of SiC mainly contain Pd. Ag has been observed in the IPyC/SiC layer in one of the two locations. Comparison of the results to previously irradiated and analyzed, Variant 3, safety tested AGR-1 TRISO particles (AGR1-433-001 and AGR1 222-RS004) showed the grain boundary distributions have some noticeable differences. The differences in coincident site lattice grain boundary and misorientation angles are possibly inherent to the fabrication process. Neutron irradiation induced void distribution has been found to be nonuniform. A high concentration of smaller voids is found at stacking faults compared to those in the SiC matrix. Larger void sizes are observed in the SiC location that is near to the broken buffer layer. This void size variation with integrity of buffer layer can potentially affect the fission product retention. However, the average void size continuously decreases along the radius of SiC in both locations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Advanced Electron Microscope and Micro Analysis of TRISO coated Particles: FY2020 Overview

Objectives Understanding Effects of Irradiation on TRISO layers Fission product chemistry and behavior in UCO kernel Identify and Understand Fission Product Transport Mechanisms in TRISO Coated Particles Outcomes and Impact Impact on Performance Improve Predictive Behavior Modeling Kernel Behavior: Release from kernel; release from whole particle Known Fission Product Transport Mechanisms

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

An Overview of Neutron Irradiated SiC Layer Behavior using Micro-and Nano-Characterization Techniques

The complexity of fission product distribution and composition within the SiC layer of tristructural isotropic (TRISO) coated particles, irradiation effects on the SiC structure as well as the variable nature of metallic fission product release, has led to the exploration of multiple micro- and nano-characterization techniques. The fine scale of the fission product precipitates necessitates unique learnings and application of electron microscopic techniques with irradiated fuel during the Advanced Gas Reactor (AGR)-1 experiment analysis. A summarized discussion on the specific advanced techniques with associated method development for TRISO coated particles is provided followed by the down selected techniques currently considered to provide the highest impact. Techniques considered are electron probe micro-analyzer (EPMA), scanning transmission electron microscopy (STEM), and Precession electron diffraction (PED). SiC grain boundary characteristics are evaluated due to the mobility of specific fission products through grain boundaries. PED was performed for understanding the role of grain boundary character on fission product transport. One set of comparative analyses between AGR-1 and AGR-2 particles leads to a finding that the AGR-1, high-Ag-retention particle, had statistically more coincidence site lattice (CSL)-related grain boundaries (but fewer low-angle grain boundaries), compared to the AGR-2 particle. This implies that CSL-related grain boundaries may have a direct influence on Ag retention. However, precipitates were found on a relatively small fraction of CSL-related grain boundaries in both particles. In another set of comparison between AGR-1 and AGR-2 particles that were subjected to safety testing, there is significant differences in average SiC grain boundary distributions, but the fission product distributions on these grain boundaries are very similar.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Fission Product Diffusion in Silicon Carbide: As Revealed by Computer Simulations and Experimental Measurements

The diffusion and release of fission products through silicon carbide in the tri-structural isotropic (TRISO) fuel particles remain unsolved for decades. The underlying mechanism is quite challenging to be determined. To help unveil the mysterious story, the current work applies molecular dynamics method to show the stability of silver, palladium, ruthenium and iodine as an interstitial and their atomic diffusion along coincident site lattice (CSL) boundary, especially ?3 grain boundary (GB). The major finding presents a much faster diffusion along GB than in bulk for all elements considered. The reasonably close estimate to experiments and simulations where available has confirmed the important role of grain boundary diffusion of Ag and Pd in SiC. However, the discrepancy addressed in Ag with measurements from fuel studies suggest a more complicated mechanism, which might be in correlation with high energy grain boundaries or the presence of crack. The subsequent characterization of Ru and I distribution in SiC-PyC-SiC diffusion couples, which have been ion irradiated at 900?C to 10 dpa and 20 dpa, has performed by secondary ion mass spectrometry (SIMS) analysis. The experiment measurements correlate well with the grain boundary diffusion by simulation, which provide further evidences that the grain boundary diffusion cannot be neglected once the fission products are accessible at the grain boundary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗