Search NASA⌕ Search

Engineering topics

Van Stone, R. H.

Publications and source records attributed to Van Stone, R. H..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

A constitutive model for the inelastic multiaxial response of Rene 80 at 871 C and 982 C

This paper contains an extension of the uniaxial state variable constitutive model of Ramaswamy et al. (1988) to the case of multiaxial loading. The correlation between uniaxial and multiaxial loading conditions is achieved through the assumptions of material isotropy and conservation of inelastic volume. The multiaxial extension is based only on the material parameters evaluated from uniaxial loading. The research is accompanied by a multiaxial experimental program to evaluate the response of Rene 80 at 871 C and 982 C. Experiments in the program include torsion, proportional axial and torsion, and nonproportional loading. It was shown experimentally that there is no extra hardening from the multiaxial loading than results from uniaxial loading. Further, it is shown that the multiaxial model is successful in predicting the experimental results using only the parameters determined from the uniaxial experiments.

Stouffer, D. C.↗
NASA NTRS1990

Simulation of crack growth and crack closure under large cyclic plasticity

The propagation of a crack during cyclic loading with large plasticity was simulated using a finite element method. The numerical procedure included the determination of crack closing and opening by examining the contact condition of the crack surfaces in the plasticity iteration. The method was applied to the growth of cracks in Alloy 718 single edge notch specimens at 538 C subject to strain cycling under both nominally elastic and elastoplastic conditions. The results show, among other things, that the crack closure and opening stresses become more compressive as the loading becomes more plastic, and that, under a given control condition, the closure and opening stresses become less compressive as the crack propagates.

Kim, K. S.↗
NASA NTRS1990

Methods for predicting crack growth in advanced structures

Damage tolerance design and analysis is widely used in fracture critical military aircraft engine components. Linear elastic fracture mechanics techniques have been developed and verified. These are used to predict the crack propagation lives of complex geometries under mission cycling conditions. Research on methods necessary for the prediction of elevated temperature crack growth in advanced structures is reviewed. These include environmentally assisted time-dependent crack growth, non-linear fracture mechanics parameters for thermal mechanical fatigue crack growth, and finite element modeling of crack growth in composites.

Van Stone, R. H.↗
NASA NTRS1990

Application of path-independent integrals to elevated temperature crack growth

The applicability of the J-integral in elasto-plastic fracture mechanics is limited to isothermal, monotonic loading conditions from the theoretical viewpoint, while in many applications, for instance gas turbine engines, crack growth occurs in the presence of cyclic inelastic loading, thermomechanical loading and temperature gradients. A number of path-independent (P-I) integrals have been proposed which do not have the restrictions of the J-integral. A review indicates that four of these integrals, although they are not the classical conservation integrals, are path-independent under these complex loading conditions. This paper describes a combined analytical and experimental effort to evaluate the ability of these four P-I integrals to correlate the crack growth data of Alloy 718 at elevated temperatures. Results for uniform temperature, 538 C, cases indicate that all these integrals are capable of correlating the crack growth data over a wide range of cyclic plasticity.

Kim, K. S.↗
NASA NTRS1978

Investigation of the fracture mechanism of Ti-5Al-2.5Sn at cryogenic temperatures

Fractography and metallographic sectioning were used to investigate the influence of microstructure on the fracture mechanism and fracture toughness (KIC) of normal interstitial and extra low interstitial (ELI) Ti-5Al-25Sn at 20 K (-423 F) and 77 K (-320 F). Plates of each grade were mill annealed at 815 C followed by either air or furnace cooling. These variations in composition and cooling rate resulted in differences in the volume fraction and internal structure of the dispersed beta phase and in the ordering of the alpha matrix. The ELI alloys were tougher than the normal interstitial plates. KIC of the furnace-cooled ELI plate was 25% lower than that of the air-cooled ELI material. Variations in cooling rate had no influence of KIC of the normal interstitial alloys. Fractography showed that a large portion of the fracture surfaces were covered with elongated dimples. Metallographic sections of specimens deformed at 77 K showed that these features form at the intersections of slip bands or deformation twins with grain or twin boundaries. Ordering and higher interstitial levels increase the local strain in slip bands resulting in void nucleation at lower macroscopic strains and lower KIC values.

Van Stone, R. H.↗
NASA NTRS1976

Use of fractography and sectioning techniques to study fracture mechanisms

Recent investigations of the effect of microstructure on the fracture mechanisms and fracture toughness of steels, aluminum alloys, and titanium alloys have used standard fractographic techniques and a sectioning technique on specimens plastically deformed to various strains up to fracture. The specimens are prepared metallographically for observation in both optical and electron beam instruments. This permits observations to be made about the fracture mechanism as it occurs in thick sections and helps remove speculation from the interpretation of fractographic features. This technique may be used in conjunction with other standard techniques such as extraction replicas and microprobe analyses. Care must be taken to make sure that the microstructural features which are observed to play a role in the fracture process using the sectioning technique can be identified with fractography.

Van Stone, R. H.↗
NASA NTRS1974

Investigation of the plastic fracture of high-strength aluminum alloys

In a study of plastic fracture in five high-strength aluminum alloys (2014, 2024, 2124, 7075, and 7079), it has been shown that fracture toughness is affected primarily by the size and volume fraction of the larger (2 to 10 microms) second-phase particles. Certain of these particles crack at small plastic strains, nucleating voids which, with further plastic strain, coalesce to cause fracture. Not all second-phase particles crack at small plastic strains, and qualitative analysis of those which are primarily responsible for void nucleation shows that they contain iron or silicon or both. This result suggests that a reduction in the iron and silicon impurity content of the alloys should improve fracture toughness without loss of strength.

Van Stone, R. H.↗