Engineering topics

Vary, A.

Publications and source records attributed to Vary, A..

At least 55 records · Page 3

NASA NTRS1978

Quantitative ultrasonic evaluation of mechanical properties of engineering materials

Current progress in the application of ultrasonic techniques to nondestructive measurement of mechanical strength properties of engineering materials is reviewed. Even where conventional NDE techniques have shown that a part is free of overt defects, advanced NDE techniques should be available to confirm the material properties assumed in the part's design. There are many instances where metallic, composite, or ceramic parts may be free of critical defects while still being susceptible to failure under design loads due to inadequate or degraded mechanical strength. This must be considered in any failure prevention scheme that relies on fracture analysis. This review will discuss the availability of ultrasonic methods that can be applied to actual parts to assess their potential susceptibility to failure under design conditions.

Vary, A.↗

NASA NTRS1978

Correlations between ultrasonic and fracture toughness factors in metallic materials

A heuristic mathematical basis is proposed for the experimental correlations found between ultrasonic propagation factors and fracture toughness factors in metallic materials. A crack extension model is proposed wherein spontaneous stress (elastic) waves produced during microcracking are instrumental in promoting the onset of unstable crack extension. Material microstructural factors involved in this process are measurable by ultrasonic probing. Experimental results indicate that ultrasonic attenuation and velocity measurements will produce significant correlations with fracture toughness properties and also yield strength.

Vary, A.↗

NASA NTRS1978

Correlation of fiber composite tensile strength with the ultrasonic stress wave factor

An ultrasonic-acoustic technique was used to indicate the strength variations of tensile specimens of a graphite-epoxy composite. A 'stress wave factor' was determined and its value was found to depend on variations of the fiber-resin bonding as well as fiber orientation. The fiber orientations studied were 0 deg (longitudinal), 10 deg (off-axis), 90 deg (transverse), (0 deg/+ or - 45 deg/0) symmetrical, and (+ or - 45 deg) symmetrical. The stress wave factor can indicate variations of the tensile and shear strengths of composite materials. The stress wave factor was also found to be sensitive to strength variations associated with microporosity and differences in fiber-resin ratio.

Vary, A.↗

NASA NTRS1978

Use of an ultrasonic-acoustic technique for nondestructive evaluation of fiber composite strength

Details of the method used to measure the stress wave factor are described. Frequency spectra of the stress waves are analyzed in order to clarify the nature of the wave phenomena involved. The stress wave factor was measured with simple contact probes requiring only one-side access to a part. This is beneficial in nondestructive evaluations because the waves can run parallel to fiber directions and thus measure material properties in directions assumed by actual loads. The technique can be applied where conventional through transmission techniques are impractical or where more quantitative data are required. The stress wave factor was measured for a series of graphite/polyimide composite panels, and results obtained are compared with through transmission immersion ultrasonic scans.

Vary, A.↗

NASA NTRS1978

Correlations between ultrasonic and fracture toughness factors in metallic materials

A heuristic mathematical basis was proposed for the experimental correlations found between ultrasonic propagation factors and fracture toughness factors in metallic materials. A crack extension model was developed wherein spontaneous stress (elastic) waves produced during microcracking are instrumental in promoting the onset of unstable crack extension. Material microstructural factors involved in the process are measurable by ultrasonic probing. Experimental results indicate that ultrasonic attenuation and velocity measurements will produce significant correlations with fracture toughness properties and also yield strength.

Vary, A.↗

NASA NTRS1978

Correlation of Fiber Composite Tensile Strength with the Ultrasonic Stress Wave Factor

An ultrasonic-acoustic technique was used to indicate the strength variations of tensile specimens of a graphite-epoxy composite. A stress wave factor was determined and its value was found to depend on variations of the fiber-resin bonding as well as fiber orientation. The fiber orientations studied were 0 deg (longitudinal), 10 deg (off-axis), 90 deg (transverse), 0 deg + or - 45 deg/0 deg symmetrical, and + or - 45 deg] symmetrical. The stress wave factor can indicate variations of the tensile and shear strengths of composite materials. The stress wave factor was also found to be sensitive to strength variations associated with microporosity and differences in fiber-resin ratio.

Vary, A.↗

NASA NTRS1978

Quantitative Ultrasonic Evaluation of Mechanical Properties of Engineering Materials

Progress in the application of ultrasonic techniques to nondestructive measurement of mechanical strength of engineering materials is reviewed. A dormant concept in nondestructive evaluation (NDE) is invoked. The availability of ultrasonic methods that can be applied to actual parts to assess their potential susceptibility to failure under design conditions is discussed. It was shown that ultrasonic methods yield measurements of elastic moduli, microstructure, hardness, fracture toughness, tensile strength, yield strength, and shear strength for a wide range of materials (including many types of metals, ceramics, and fiber composites). It was also indicated that although most of these methods were shown feasible in laboratory studies, more work is needed before they can be used on actual parts in processing, assembly, inspection, and maintenance lines.

Vary, A.↗

NASA NTRS1978

Use of an ultrasonic-acoustic technique for nondestructive evaluation of fiber composite strength

This report describes the ultrasonic-acoustic technique used to measure a 'Stress Wave Factor'. In a prior study this factor was found effective in evaluating the interlaminar shear strength of fiber-reinforced composites. Details of the method used to measure the stress wave factor are described. In addition, frequency spectra of the stress waves are analyzed in order to clarify the nature of the wave phenomena involved. The stress wave factor can be measured with simple contact probes requiring only one-side access to a part. This is beneficial in nondestructive evaluations because the waves can run parallel to fiber directions and thus measure material properties in directions assumed by actual loads. Moreover, the technique can be applied where conventional through transmission techniques are impractical or where more quantitative data are required. The stress wave factor was measured for a series of graphite/polyimide composite panels and results obtained are compared with through transmission immersion ultrasonic scans.

Vary, A.↗

NASA NTRS1977

Ultrasonic strength evaluation of fiber-reinforced composites

Ultrasonic method of nondestructive evaluation of fiber reinforced composite structures has sensitivity to detect small distributed inadequacies such as microvoids and microfractures which effect strength and continuity of composite.

Vary, A.↗

NASA NTRS1977

Ultrasonic measurement of fracture toughness

Inexpensive nondestructive method ranks materials by crack toughness. Method can reduce expenses involved in conventional mechanical destructive testing and can be inspection tool in determining local variations of materials in fracture-prone components.

Vary, A.↗

NASA NTRS1977

Ultrasonic evaluation of the strength of unidirectional graphite-polyimide composites

An acoustic-ultrasonic method is described that was successful in ranking unidirectional graphite-polyimide composite specimens according to variations in interlaminar shear strength. Using this method, a quantity termed the stress wave factor was determined. It was found that this factor increases directly with interlaminar shear strength. The key variables in this investigation were composite density, fiber weight fraction, and void content. The stress wave factor and other ultrasonic factors that were studied were found to provide a powerful means for nondestructive evaluation of mechanical strength properties.

Vary, A.↗

NASA NTRS1976

Correlations among ultrasonic propagation factors and fracture toughness properties of metallic materials

Empirical evidence was developed to show that a close relation exists among fracture toughness, yield strength, and ultrasonic attenuation properties of metallic materials. The evidence was obtained by ultrasonic probing of specimens of two maraging steels and a titanium alloy. It was concluded that nondestructive ultrasonic methods can be used to indirectly evaluate fracture-related material properties. The results suggest that these nondestructive ultrasonic measurements can also serve as an adjunct to destructive testing, measurement, and analysis of fracture properties.

Vary, A.↗

NASA NTRS1976

Correlations among ultrasonic propagation factors and fracture toughness properties of metallic materials

Vary, A.↗

NASA NTRS1976

Inspection of composites using a computer-based real-time radiographic facility

A radiographic inspection facility was developed at the NASA Lewis Research Center. The facility uses a digital computer to provide enhanced images in near real-time. Some capabilities of the facility are demonstrated in the inspection of a fan frame ring for an experimental aircraft gas turbine. The ring was fabricated from a carbon-fiber-reinforced epoxy composite material. Inspection procedures were evaluated, and comparisons were made with an ultrasonic C-scan and conventional film X-ray.

Roberts, E., Jr.↗

NASA NTRS1975

The feasibility of ranking material fracture toughness by ultrasonic attenuation measurements

A preliminary study was conducted to assess the feasibility of ultrasonically ranking material fracture toughness. Specimens of two grades of maraging steel for which fracture toughness values were measured were subjected to ultrasonic probing. The slope of the attenuation coefficient vs frequency curve was empirically correlated with the plane strain fracture toughness value for each grade of steel.

Vary, A.↗

NASA NTRS1975

Isometric scan method for ultrasonic evaluation of composite panels

I-scan form of data presentation provides more direct information on nature and severity of flaws present in test specimen and is more easily interpreted by inspector than conventional C-scans currently used. It also offers potential savings in inspection time and cost.

Vary, A.↗

NASA NTRS1975

The feasibility of ranking material fracture toughness by ultrasonic attenuation measurements

A preliminary study was conducted to assess the feasibility of ultrasonically ranking material fracture toughness. Specimens of two grades of maraging steel for which fracture toughness values were measured were subjected to ultrasonic probing. The slope of the attenuation coefficient versus frequency curve was empirically correlated with the plane strain fracture toughness value for each grade of steel.

Vary, A.↗

NASA NTRS1974

Guidebook of nondestructive evaluation techniques for materials and structures

Seventy nondestructive techniques for evaluating material and structures are described in guidebook. Standardized format facilitates comparison of their merits and limitations for solving various problems. Guide includes index of flaw types and tabulated guide to use of nondestructive evaluation techniques. Alternative technique names are cross-referenced.

Vary, A.↗