Engineering topics

Vasquez, P.

Publications and source records attributed to Vasquez, P..

6 records

NASA NTRS1993

Effects of process variables on the properties of YBa2Cu3O(7-x) ceramics formed by investment casting

An investment casting process has been developed to produce net-shape, superconducting ceramics. In this work, a factorial experiment was performed to determine the critical process parameters for producing cast YBa2Cu3O7 ceramics with optimum properties. An analysis of variance procedure indicated that the key variables in casting superconductive ceramics are the particle size distribution and sintering temperature. Additionally, the interactions between the sintering temperature and the other process parameters (e.g., particle size distribution and the use of silver dopants) were also found to influence the density, porosity, and critical current density of the fired ceramics.

Hooker, M. W.↗

NASA NTRS1986

Pressure Rig for Repetitive Casting

Equipment life increased by improved insulation. New design cuts time of preparation for casting from several days to about 1 hour. Savings due to elimination of lengthy heating and drying operations associated with preparation of ceramic mold. Quality of casting improved because moisture in cavity eliminated by use of insulating material, and more uniform pressure applied to process. Commercial blanket insulator protects components from heat, increasing life of pressure rig and enabling repeated use. Improved heat protection allows casting of brass and other alloys with higher melting temperatures in pressure rig.

Vasquez, P.↗

NASA NTRS1986

Thermoplastic Composites for Research-Model Components

Oriented unidirectional prepreg tapes formed in ceramic molds. New technique developed at Langley Research Center, using ceramic mold for fabrication of models from graphite/thermoplastic materials. Upper surface of wings and fuselage of advanced airplane selected as shape to test fabrication technique. Technique well suited for other complex shapes as well. Thermoplastic composite easily workable with normal shop equipment and painted and repaired by standard methods.

Guenther, B. F.↗

NASA NTRS1982

A ceramic nozzle for the NASA-Langley 2.4-m /8.0-ft/ high temperature structures tunnel

Two materials, a refractory castable ceramic and a SiO2-SiO2 composite, were fabricated as nozzle inserts for the Langley Research Center's 2.4-m (8.0-ft) high temperature structures tunnel. The high pressure and intense heat of the CH4-air products of the combustion-gas stream limits the materials that can be used in this tunnel. The castable-ceramic material showed good resistance to erosion and the thermal loads imposed on it by the gas stream but failed in tension when subjected to high hoop stresses. The SiO2-SiO2-composite nozzle insert withstood the thermomechanical loads but eroded unacceptably with increasing test temperature and pressure.

Buckley, J. D.↗

NASA NTRS1981

Ceramic and coating applications in the hostile environment of a high temperature hypersonic wind tunnel

A Mach 7, blowdown wind tunnel was used to investigate aerothermal structural phenomena on large to full scale high speed vehicle components. The high energy test medium, which provided a true temperature simulation of hypersonic flow at 24 to 40 km altitude, was generated by the combustion of methane with air at high pressures. Since the wind tunnel, as well as the models, must be protected from thermally induced damage, ceramics and coatings were used extensively. Coatings were used both to protect various wind tunnel components and to improve the quality of the test stream. Planned modifications for the wind tunnel included more extensive use of ceramics in order to minimize the number of active cooling systems and thus minimize the inherent operational unreliability and cost that accompanies such systems. Use of nonintrusive data acquisition techniques, such as infrared radiometry, allowed more widespread use of ceramics for models to be tested in high energy wind tunnels.

Puster, R. L.↗

NASA NTRS1979

Quick-connect threaded attachment joint

Joint is self-aligning and tightens with only sixty-five degrees of rotation for quick connects and disconnects. Made of injection-molded plastics or cast or machined aluminum, joint can carry wires, tubes, liquids, or gases. When two parts of joint are brought together, their shapes align them. Small projections on male section and slots on female section further aid alignment; slight rotation of male form engages projections in slots. At this point, threads engage and male section is rotated until joint is fully engaged.

Lucy, M. H.↗