Search NASA⌕ Search

Engineering topics

Vasu, Subith S.

Publications and source records attributed to Vasu, Subith S..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

AUTOIGNITION DELAY TIMES FOR REFORMATE GAS MIXTURES FROM METHANE GAS ENGINES

Methane slip is a prominent issue in natural gas reciprocating engines that are used in transportation and marine applications. The incomplete combustion that results in methane slip can be resolved with the introduction of hydrogen within the combustion mixture to improve methane oxidation and further enable combustion within the engine crevices where methane has previously remained unreacted. Steam methane reforming (SMR) is a common method used to produce hydrogen and can be used to design an onboard device to reduce methane slip from reciprocating engines. The development of this reformer device requires the validation of high-fidelity chemical kinetic models at the low temperatures of the crevice volumes of these engines. In this work, auto-ignition data is obtained using a shock tube at lean (φ—0.714 or λ—1.4) and stoichiometric (φ, λ = 1) equivalence ratios spanning a temperature range of 1042–1234 K at the 80-bar operating pressure of the test engine. Blends of methane, hydrogen, and reformate products from the SMR reaction are shock-heated in synthetic air, with the ignition delay time measured using an OH* chemiluminescence detector at 310 nm and a CH* detector at 430 nm. The experimental results are compared to several state-of-the-art chemical kinetic mechanisms from the literature. In general, most of the mechanisms show very good agreement with experiments at higher temperatures, with simulation results showing little deviation from experiments at lower temperatures. A sensitivity analysis was conducted, and the results reveal that the reaction H2 + CH3O2 = H + CH3O2H has a very significant role in determining low-temperature ignition delay times (IDTs) of SMR mixtures. These findings provide valuable insights into the chemical kinetics governing methane reformate combustion and contribute to the optimization of onboard reformer designs aimed at mitigating methane slip in natural gas-fueled engines.

Fraze, Matthew↗
DOE OSTI2024

Ignition Delay Times and Chemical Kinetic Model Validation for Hydrogen and Ammonia Blending With Natural Gas at Gas Turbine Relevant Conditions

Ignition delay times from undiluted mixtures of natural gas (NG)/H 2 /Air and NG/NH 3 /Air were measured using a high-pressure shock tube at the University of Central Florida. The combustion temperatures were experimentally tested between 1000 and 1500 K near a constant pressure of 25 bar. As mentioned, mixtures were kept undiluted to replicate the same chemistry pathways seen in gas turbine combustion chambers. Recorded combustion pressures exceeded 200 bar due to the large energy release, hence why these were performed at the high-pressure shock tube facility. The data are compared to the predictions of the NUIGMech 1.1 mechanism for chemical kinetic model validation and refinement. An exceptional agreement was shown for stoichiometric conditions in all cases but strayed at lean and rich equivalence ratios, especially in the lower temperature regime of H 2 addition and all temperature ranges of the baseline NG mixture. Hydrogen addition also decreased ignition delay times by nearly 90%, while NH 3 fuel addition made no noticeable difference in ignition time. NG/NH 3 exhibited similar chemistry to pure NG under the same conditions, which is shown in a sensitivity analysis. Here, the reaction CH 3 + O 2 = CH 3 O + O is identified and suggested as a possible modification target to improve model performance. Increasing the robustness of chemical kinetic models via experimental validation will directly aid in designing next-generation combustion chambers for use in gas turbines, which in turn will greatly lower global emissions and reduce greenhouse effects.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Hydrogen and Ammonia Blending With Natural Gas: Ignition Delay Times and Chemical Kinetic Model Validation at Gas Turbine Relevant Conditions

Abstract Ignition delay times from undiluted mixtures of natural gas (NG)/H2/Air and NG/NH3/Air were measured using a high-pressure shock tube at the University of Central Florida. The combustion temperatures were experimentally tested between 1000–1500 K near a constant pressure of 25 bar. As mentioned, mixtures were kept undiluted to replicate the same chemistry pathways seen in gas turbine combustion chambers. Recorded combustion pressures exceeded 200 bar due to the large energy release, hence why these were performed at the high-pressure shock tube facility. The data is compared to the predictions of the NUIGMech 1.1 mechanism for chemical kinetic model validation and refinement. An exceptional agreement was shown for stoichiometric conditions in all cases but strayed at lean and rich equivalence ratios, especially in the lower temperature regime of H2 addition and all temperature ranges of the baseline NG mixture. Hydrogen addition also decreased ignition delay times by nearly 90%, while NH3 fuel addition made no noticeable difference in ignition time. NG/NH3 exhibited similar chemistry to pure NG under the same conditions, which is shown in a sensitivity analysis. The reaction CH3 + O2 = CH3O + O is identified and suggested as a possible modification target to improve model performance. Increasing the robustness of chemical kinetic models via experimental validation will directly aid in designing next-generation combustion chambers for use in gas turbines, which in turn will greatly lower global emissions and reduce greenhouse effects.

Pierro, Michael↗
DOE OSTI2023

Laminar Burning Speed Measurements of Hydrogen/Natural Gas Mixtures

Abstract To address the shortage of fossil fuels and the environmental impact of exhaust emissions, research efforts in combustion seek to identify candidates for sustainable fuels. Hydrogen is an example, from which water is produced as the main combustion product. However, when used as neat hydrogen, it is very difficult to control hydrogen combustion due to its high flame speed, pre-ignition propensity, and flashback characteristics. One method to control hydrogen combustion is to blend it with a well-established fuel. Natural gas is a common fuel for use in engines or gas turbines. Natural gas is characterized by slow flame speeds and poor lean-burn ability; thus, engine power is decreased in the lean-burn region. Consequently, natural gas engines are typically operated at stoichiometric conditions to maximize output. Blending hydrogen to natural gas has several advantages: (i) Control of hydrogen’s ignition characteristics, (ii) extension of Natural gas’s lower flammability limit — making it easier to ignite, and (iii) reduced greenhouse gas emissions. In this study, the laminar burning speed (LBS) for neat natural gas and natural gas/hydrogen mixtures at 5 atm and 296 K were measured. Schlieren optical imaging was utilized to validate laminar flame conditions and further investigate the structure of natural gas/hydrogen flames. Results indicate that replacing 50% of natural gas with hydrogen increases the peak laminar burning velocity by a factor of ∼1.6 times. LBS simulations were conducted with NUI 1.1 and UCF NG/H2 mechanisms; Predictions by both mechanisms were found to be satisfactory for neat NG mixtures. However, for 50% NG/ 50% H2 mixture, the true LBS for fuel-lean conditions was under-predicted by both models, while predictions for fuel-rich conditions were satisfactory. Additionally, a literature review and similar experimental analysis will be performed for methane, ammonia, and hydrogen fuel blends to better understand the combustion phenomena of natural gas fuels.

Yovino, Louis↗
DOE OSTI2022

High-Fuel Loading Ignition Delay Time Characterization of Hydrogen/Natural Gas/Ammonia at Gas Turbine-Relevant Conditions Inside a High-Pressure Shock Tube

Abstract This study explores the combustion characterization of high-fuel percentage, air-diluted mixtures of H2 mixed with natural gas (NG) as well as mixtures of H2 and NH3 at temperatures and pressures relevant to turbine operating conditions (20–30 bar, 1000–1500 K). Lower temperatures (below 1070 K) exhibit preignition characteristics due to non-homogeneity. An attempt to mitigate these occurrences at high pressures is investigated using the constrained reaction volume (CRV) stage-filling technique. Due to the need to further refine the facility CRV stage-filling uncertainty, only higher temperature data will be interpreted at this time. The test conditions in this study closely replicate the temperatures, pressures, and mixtures that would be seen in hydrogen-powered gas turbines, making it the first to explore such conditions. The experimental IDTs were compared against the current state-of-the-art chemical kinetic models for mechanism validation. The current work will advance H2-powered turbines and aims to determine the optimum molecular ratio of H2 when mixed with natural gas.

Pierro, Michael↗
DOE OSTI2022

Characterization of a new ultra-high pressure shock tube facility for combustion and propulsion studies

A new shock tube facility has been designed, constructed, and characterized at the University of Central Florida. This facility is capable of withstanding pressures of up to 1000 atm, allowing for combustion diagnostics of extreme conditions, such as in rocket combustion chambers or in novel power conversion cycles. For studies with toxic gas impurities, the high initial pressures required the development of a gas delivery system to ensure the longevity of the facility and the safety of the personnel. Data acquisition and experimental propagation were implemented with remote access to ensure safety, paired with a LabVIEW- and Python-based user interface. Thus far, test pressures of 270 atm, blast pressures of 730 atm, and temperatures approaching 10 000 K have been achieved. The extreme limitations of this facility allow for emission spectroscopy to be performed during the oxidation of fuel mixtures, e.g., alkanes diluted in argon and carbon dioxide. Ignition delay times were determined and compared to simulations using chemical kinetic mechanisms. The design, experimental procedures, processes of analysis, and uncertainty determination are outlined, and typical pressure profiles are compared with a new gas dynamics solver and empirical correlations developed across multiple shock tube facilities. Preliminary reactive mixture analyses are included with further investigation of the mixtures outlined.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Shock tube investigation of high-temperature, extremely-rich oxidation of several co-optima biofuels for spark-ignition engines

To reduce the reliance on fossil fuels in the transportation sector and increase combustion efficiency, the Co-Optima initiative from US Department of Energy identified the top 10 biofuels for downsized, boosted, spark-ignition engines. Most of these biofuels have detailed reaction mechanisms available in literature developed based on studies at temperatures lower than 1700 K and an equivalence ratio of less than five. As such, the performance of these detailed mechanisms at high temperature and extremely rich conditions are unknown. It is important to validate kinetic mechanisms at these conditions because they are conducive to soot formation. Prediction of soot by chemical kinetic models relies on the prediction of underlying benchmark species like carbon monoxide and ethylene. In this work, we conduct high temperature (1700–2050 K) and high equivalence ratio(Φ=8.6) oxidation of these biofuels, namely 2,4,4-trimethyl-1-pentene (α-diisobutylene), ethanol, cyclopentanone, methyl acetate, and 2-methylfuran, blended in ethylene behind reflected shock waves at 4–4.7 atm pressure. Carbon monoxide and ethylene time histories are measured simultaneously using a continuous feedback quantum cascade laser near 4.9 µm and a tunable CO 2 gas laser at 10.532 nm, respectively. Results show that ethanol blend forms more carbon monoxide than other biofuels and consumes ethylene faster than the biofuel blends in the temperature range considered. Overall, the performance of different mechanisms in literature are evaluated against the experimental results. The novel reaction mechanism ‘the Co-Optima model’, which includes the sub mechanisms for all the biofuels in this study, was found to be the best mechanism for the experimental conditions studied.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

An experimental and detailed kinetic modeling study of the pyrolysis and oxidation of allene and propyne over a wide range of conditions

Allene and propyne are important intermediates in the pyrolysis and oxidation of higher hydrocarbon fuels, and they are also a major source of propargyl radical formation, which can recombine into different C 6 H 6 isomers and finally produce soot. In a prior work (Panigrahy et al., “A comprehensive experimental and improved kinetic modeling study on the pyrolysis and oxidation of propyne”, Proc. Combust. Inst 38 (2021)), the pyrolysis, ignition , and laminar flame speed of propyne were investigated. To understand the kinetic features of initial fuel breakdown and oxidation of the two C 3 H 4 isomers, new measurements for allene pyrolysis and oxidation are conducted in the present paper at the same operating conditions as those studied previously for propyne. Ignition delay times of allene are measured using a high-pressure shock tube and a heated twin-opposed piston rapid compression machine in the temperature range 690– 1450 K at equivalence ratios of 0.5, 1.0 and 2.0 in ‘air’, and at pressures of 10 and 30 bar. Pyrolysis species measurements of allene and propyne are also performed using a gas chromatography integrated singlepulse shock tube in the temperature range 1000–1700 K at pressure of 2 and 5 bar. Furthermore, laminar flame speeds of allene are measured at elevated gas temperatures of 373 K at pressures of 1 and 2 bar for a wide range of equivalence ratios from 0.6 to 1.5. A newly updated kinetic mechanism developed for this study is the first model that can well reproduce all of the experimental results for both allene and propyne. It is observed that in the pyrolysis process, allene dissociates faster than propyne. Both isomers exhibit similar ignition delay times at high temperatures (>1000 K), while, at intermediate temperatures (770–1000 K) propyne is the faster to ignite, and at lower temperatures (< 770 K) allene becomes more reactive. Furthermore, laminar flame speeds for propyne are found to be slightly faster than those for allene under the conditions studied in this work

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Oxidation and pyrolysis of methyl propyl ether

The ignition, oxidation, and pyrolysis chemistry of methyl propyl ether (MPE) was probed experimentally at several different conditions, and a comprehensive chemical kinetic model was constructed to help understand the observations, with many of the key parameters computed using quantum chemistry and transition state theory. Experiments were carried out in a shock tube measuring time variation of CO concentrations, in a flow tube measuring product concentrations, and in a rapid compression machine (RCM) measuring ignition delay times. The detailed reaction mechanism was constructed using the Reaction Mechanism Generator software. Sensitivity and flux analyses were used to identify key rate and thermochemical parameters, which were then computed using quantum chemistry to improve the mechanism. Validation of the final model against the 1-20 bar 600-1500 K experimental data is presented with a discussion of the kinetics. The model is in excellent agreement with most of the shock tube and RCM data. Strong non-monotonic variation in conversion and product distribution is observed in the flow-tube experiments as the temperature is increased, and unusually strong pressure dependence and significant heat release during the compression stroke is observed in the RCM experiments. These observations are largely explained by a close competition between radical decomposition and addition to O2 at different sites in MPE; this causes small shifts in conditions to lead to big shifts in the dominant reaction pathways. The validated mechanism was used to study the chemistry occurring during ignition in a diesel engine, simulated using Ignition Quality Test (IQT) conditions. At the IQT conditions, where the MPE concentration is higher, bimolecular reactions of peroxy radicals are much more important than in the RCM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Accurate prediction of terahertz spectra of molecular crystals of fentanyl and its analogs

Fentanyl is a potent synthetic opioid pain reliever with a high bioavailability that can be used as prescription anesthetic. Rapid identification via non-contact methods of both known and emerging opioid substances in the fentanyl family help identify the substances and enable rapid medical attention. We apply PBEh-3c method to identify vibrational normal modes from 0.01 to 3 THz in solid fentanyl and its selected analogs. The molecular structure of each fentanyl analog and unique arrangement of H-bonds and dispersion interactions significantly change crystal packing and is subsequently reflected in the THz spectrum. Further, the study of THz spectra of a series of stereoisomers shows that small changes in molecular structure results in distinct crystal packing and significantly alters THz spectra as well. We discuss spectral features of synthetic opioids with higher potency than conventional fentanyl such as ohmefentanyl and sufentanil and discover the pattern of THz spectra of fentanyl analogs.

42 ENGINEERING↗
DOE OSTI2020

Elucidating the differences in oxidation of high-performance α- and β- diisobutylene biofuels via Synchrotron photoionization mass spectrometry

Abstract Biofuels are a promising ecologically viable and renewable alternative to petroleum fuels, with the potential to reduce net greenhouse gas emissions. However, biomass sourced fuels are often produced as blends of hydrocarbons and their oxygenates. Such blending complicates the implementation of these fuels in combustion applications. Variations in a biofuel’s composition will dictate combustion properties such as auto ignition temperature, reaction delay time, and reaction pathways. A handful of novel drop-in replacement biofuels for conventional transportation fuels have recently been down selected from a list of over 10,000 potential candidates as part of the U.S. Department of Energy’s (DOE) Co-Optimization of Fuels and Engines (Co-Optima) initiative. Diisobutylene (DIB) is one such high-performing hydrocarbon which can readily be produced from the dehydration and dimerization of isobutanol, produced from the fermentation of biomass-derived sugars. The two most common isomers realized, from this process, are 2,4,4-trimethyl-1-pentene (α-DIB) and 2,4,4-trimethyl-2-pentene (β-DIB). Due to a difference in olefinic bond location, the α- and β- isomer exhibit dramatically different ignition temperatures at constant pressure and equivalence ratio. This may be attributed to different fragmentation pathways enabled by allylic versus vinylic carbons. For optimal implementation of these biofuel candidates, explicit identification of the intermediates formed during the combustion of each of the isomers is needed. To investigate the combustion pathways of these molecules, tunable vacuum ultraviolet (VUV) light (in the range 8.1–11.0 eV) available at the Lawrence Berkeley National Laboratory’s Advanced Light Source (ALS) has been used in conjunction with a jet stirred reactor (JSR) and time-of-flight mass spectrometry to probe intermediates formed. Relative intensity curves for intermediate mass fragments produced during this process were obtained. Several important unique intermediates were identified at the lowest observable combustion temperature with static pressure of 93,325 Pa and for 1.5 s residence time. As this relatively short residence time is just after ignition, this study is targeted at the fuels’ ignition events. Ignition characteristics for both isomers were found to be strongly dependent on the kinetics of C 4 and C 7 fragment production and decomposition, with the tert-butyl radical as a key intermediate species. However, the ignition of α-DIB exhibited larger concentrations of C 4 compounds over C 7 , while the reverse was true for β-DIB. These identified species will allow for enhanced engineering modeling of fuel blending and engine design.

09 BIOMASS FUELS↗
DOE OSTI2020

Influence of Equation-of-States on Supercritical CO2 Combustion Mixtures

Abstract Fossil fuel based direct-fired supercritical CO2 (sCO2) cycles are gaining the attention of industry, academia, and government due to their remarkable efficiency and carbon capture at high-source temperatures. Modeling plays an important role in the development of sCO2 combustors because experiments are very expensive at the designed operating conditions of these direct-fired cycles. Inaccurate density estimates are detrimental to the simulation output. Hence, this work focuses on comprehensive evaluation of the influence and applicability of various equation-of-states (EOS) which are being used in the supercritical combustion modeling literature. A state-of-the-art supercritical combustion modeling methodology is used to simulate counter-flow supercritical CO2 flames by using various equation-of-states. The results show that using the corresponding state principle to evaluate compressibility factor is not accurate. Also, van der Waal type EOSs predictions can be as accurate as complex Benedict–Webb–Rubin EOSs; hence van der Waal EOSs are more suitable to simulate sCO2 combustor simulations. Non-ideal effects are significant under the operating conditions considered in this work. The choice of EOS significantly influences the flame structure and heat release rate. Also, assuming the binary interaction parameter as zero is reasonable in sCO2 combustion simulations.

Energy & Fuels↗
DOE OSTI2020

Ignition delay time and speciation of dibutyl ether at high pressures

Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550–650 K, P = 10, 20, 40 bar, φ = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900–1300 K, P = 20, 40 bar, φ = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100–1400 K, P = 20 bar. Pressure time-histories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. We found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.

09 BIOMASS FUELS↗
DOE OSTI2020

Reflected shock-initiated ignition probed via simultaneous lateral and endwall high-speed imaging with a transparent, cylindrical test-section

A TRAnsparent cylindrical (TRAC) shock tube test section has been developed to explore the ignition structure behind reflected shockwaves via simultaneous lateral and endwall high-speed imaging using three fuel/oxidizer mixtures: 0.1% n-C 7 H 16 /1.10% O 2 /4.14% N 2 /94.66% Ar, 0.1% iC 8 H 18 /1.25% O 2 /4.69% N 2 /93.96% Ar, and 5% CH 4 /10% O 2 /85% CO 2 . During mild ignition, the first exothermic centers were located outside of the observable test section. It is shown that with increasing temperature the far-wall ignition events move closer to the endwall, until a strong ignition is achieved. The temperature gradients that promote mild ignition were quantified and were found to have a slight dependence on fuel with the RMS temperature gradients being 0.80% for n-heptane and 1.07% for isooctane. The impact of temperature gradients on metrics used to improve kinetic models, such as species time histories, is noteworthy. From this temperature gradient, an experimental correlation is provided to estimate the transition temperature from mild to strong ignition for a mixture. The effect of diagnostic location in non-homogeneous reactions is quantified in reference to ignition delay. In conclusion, the unique and insightful perspective on the ignition process under heavy shock bifurcation is also discussed.

02 PETROLEUM↗
DOE OSTI2020

Experimental and Kinetic Modeling Study of Laminar Burning Velocities of Cyclopentanone and Its Binary Mixtures with Ethanol and n-Propanol

Cyclopentanone is a promising biofuel that can enable more efficient engine operation and increase the fuel economy of the light duty fleet over current and planned technology developments. While the ignition of cyclopentanone has been investigated in detail, more studies on the laminar burning velocities of cyclopentanone are called for. In this work, the laminar burning velocities of cyclopentanone (C 5 H 8 O) have been measured using the heat flux and spherical flame methods at 1 atm, equivalence ratios from 0.7 to 1.6, and initial temperatures of 328, 353, and 428 K. To further investigate the relationship between the molecular structure and laminar burning velocity, identical experiments were also performed for binary mixtures of cyclopentanone with ethanol and n-propanol at 1:1 (mol). The consistency between the experimental data sets obtained in this work and literature data sets has been evaluated. Here, a recently published mechanism of cyclopentanone was used for simulation after adopting the submechanism of n-propanol. Good agreement has been seen between experimental and simulated results for all flames. To qualitatively explain the characteristics of the laminar burning velocity of cyclopentanone and the differences with those of ethanol and n-propanol, sensitivity analysis and reaction pathway analysis have been performed to compare the chemistry of the fuels under flame conditions, which revealed how the molecular structure of cyclopentanone could affect its laminar burning velocity. Compared to ethanol and n-propanol, cyclopentanone does not have primary carbon atoms in its molecule, leading to lower production of methyl radicals. Meanwhile, the carbonyl group in the cyclopentanone molecule is mostly released as CO in the decomposition of multiple intermediates accompanied by the production of unsaturated C 2 and C 4 species, especially C 2 H 4 and C 2 H 3 . Both features contribute to the high laminar burning velocity of cyclopentanone.

09 BIOMASS FUELS↗