Search NASA⌕ Search

Engineering topics

Vedder, Raymond James

Publications and source records attributed to Vedder, Raymond James.

Plutonium-238 Production Program Results, Implications, and Projections from Irradiation and Examination of Initial NpO 2 Test Targets for Improved Production

An alternative target design with potential improvements, including a major increase in 238 Pu production rate and annual capacity; fewer targets to be fabricated, irradiated, and processed; and a significant replacement of a large volume of caustic-nitrate, aluminum-bearing radioactive liquid waste with a smaller volume of solid metal waste, has been conceived and evaluated using reactor physics and thermal-hydraulic analyses. The alternative target design uses pressed pellets of 237 NpO 2 , sintered to 92% to 93% of theoretical density, and stacked inside a Zircaloy-4 cladding tube. Additionally, four test targets were fabricated, irradiated, and examined. No melting or other potential problems were indicated. Projections from measured constituents indicated annual production could be increased by a factor of ~2, and the number of targets required to be fabricated, irradiated, and processed could be reduced by a factor of ~5.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Demonstration of Integrated PostIrradiation Process Steps forMultikilogram Amounts of Low- and High-Burnup Used Nuclear Fuels

sponsored research and development (R&D) on the advanced, closed nuclear fuel cycle, including post-irradiation processing of used fuels, recovery of separated components, and preparation of recycle nuclear fuels. During the period 2007–2010, kilogram-scale demonstrations of the integrated processing steps were performed for actual light water reactor (LWR) used nuclear fuels (UNF). These integrated processing demonstrations were called “the Coupled-End-to-End” (CETE) campaigns and were associated with the Global Nuclear Energy Partnership program, which ran concurrently. The demonstrations were carried out in the shielded hot cells and associated gloveboxes located in the Irradiated Fuels Examination Laboratory (IFEL) and the Radiochemical Engineering Development Center (REDC) at the Oak Ridge National Laboratory (ORNL). Limited circulation program reports and a few technical papers were issued. The subject document provides a comprehensive summary of results, technical comparisons, and conclusions obtained from the demonstration campaigns and subsequent associated R&D.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Oak Ridge National Laboratory Preparation of Sintered 237 NpO 2 Pellets for Irradiation to Produce 238 Pu Oxide

The reference flowsheet for production of 238 Pu is by irradiation of targets containing pellets cold-pressed from a mix of NpO 2 and Al, which are referred to as cermet pellets or compacts. Oxide pellets, cold-pressed from NpO 2 , are being considered because elimination of the aluminum constituent has significant advantages in a production operation. Details of a fabrication process to make NpO 2 pellets, from preparation of neptunium oxide powder through sintering of the pressed pellets, are given. Pellets were prepared of required density and tight dimensional tolerance for fabrication of test targets that are currently being irradiated at the Oak Ridge National Laboratory High Flux Isotope Reactor. This work is part of the effort to reestablish domestic production of 238 Pu for the National Aeronautics and Space Administration and the Department of Energy.

36 MATERIALS SCIENCE↗

The Plutonium-238 Project

Explore the source record for details and available documents.

NESDPS Office of Nuclear Energy Space and Defense ↗

Evaluation of Co-precipitation Processes for the Synthesis of Mixed-Oxide Fuel Feedstock Materials

The focus of this report is the evaluation of various co-precipitation processes for use in the synthesis of mixed oxide feedstock powders for the Ceramic Fuels Technology Area within the Fuels Cycle R&D (FCR&D) Program's Advanced Fuels Campaign. The evaluation will include a comparison with standard mechanical mixing of dry powders and as well as other co-conversion methods. The end result will be the down selection of a preferred sequence of co-precipitation process for the preparation of nuclear fuel feedstock materials to be used for comparison with other feedstock preparation methods. A review of the literature was done to identify potential nitrate-to-oxide co-conversion processes which have been applied to mixtures of uranium and plutonium to achieve recycle fuel homogeneity. Recent studies have begun to study the options for co-converting all of the plutonium and neptunium recovered from used nuclear fuels, together with appropriate portions of recovered uranium to produce the desired mixed oxide recycle fuel. The addition of recycled uranium will help reduce the safeguard attractiveness level and improve proliferation resistance of the recycled fuel. The inclusion of neptunium is primarily driven by its chemical similarity to plutonium, thus enabling a simple quick path to recycle. For recycle fuel to thermal-spectrum light water reactors (LWRs), the uranium concentration can be {approx}90% (wt.), and for fast spectrum reactors, the uranium concentration can typically exceed 70% (wt.). However, some of the co-conversion/recycle fuel fabrication processes being developed utilize a two-step process to reach the desired uranium concentration. In these processes, a 50-50 'master-mix' MOX powder is produced by the co-conversion process, and the uranium concentration is adjusted to the desired level for MOX fuel recycle by powder blending (milling) the 'master-mix' with depleted uranium oxide. In general, parameters that must be controlled for co-precipitation processes include (1) feed solution concentration adjustment, (2) precipitant concentration and addition methods, (3) pH, temperature, mixing method and time, (4) valence adjustment, (5) solid precipitate separation from the filtrate 'mother liquor,' generally by means of centrifugation or filtration, and (6) temperatures and times for drying, calcination, and reduction of the MOX product powder. Also a recovery step is necessary because of low, but finite solubility of the U/TRU metals in the mother liquor. The recovery step usually involves destruction of the residual precipitant and disposal of by-product wastes. Direct denitrations of U/TRU require fewer steps, but must utilize various methods to enable production of MOX with product characteristics that are acceptable for recycle fuel fabrication. The three co-precipitation processes considered for evaluation are (1) the ammonia co-precipitation process being developed in Russia, (2) the oxalate co-precipitation process, being developed in France, and (3) the ammonium-uranyl-plutonyl-carbonate (AUPuC) process being developed in Germany. Two direct denitration processes are presented for comparison: (1) the 'Microwave Heating (MH)' automated multi-batch process developed in Japan and (2) the 'Modified Direct Denitration (MDD)' continuous process being developed in the USA. Brief comparative descriptions of the U/TRU co-conversion processes are described. More complete details are provided in the references.

Collins, Emory D↗

Synthesis and Characterization of Oxide Feedstock Powders for the Fuel Cycle R&D Program

Nuclear fuel feedstock properties, such as physical, chemical, and isotopic characteristics, have a significant impact on the fuel fabrication process and, by extension, the in-reactor fuel performance. This has been demonstrated through studies with UO{sub 2} spanning greater than 50 years. The Fuel Cycle R&D Program with The Department of Energy Office of Nuclear Energy has initiated an effort to develop a better understanding of the relationships between oxide feedstock, fresh fuel properties, and in-reactor fuel performance for advanced mixed oxide compositions. Powder conditioning studies to enable the use of less than ideal powders for ceramic fuel pellet processing are ongoing at Los Alamos National Laboratory (LANL) and an understanding of methods to increase the green density and homogeneity of pressed pellets has been gained for certain powders. Furthermore, Oak Ridge National Laboratory (ORNL) is developing methods for the co-conversion of mixed oxides along with techniques to analyze the degree of mixing. Experience with the fabrication of fuel pellets using co-synthesized multi-constituent materials is limited. In instances where atomically mixed solid solutions of two or more species are needed, traditional ceramic processing methods have been employed. Solution-based processes may be considered viable synthesis options, including co-precipitation (AUPuC), direct precipitation, direct-conversion (Modified Direct Denitration or MDD) and internal/external gelation (sol-gel). Each of these techniques has various advantages and disadvantages. The Fiscal Year 2010 feedstock development work at ORNL focused on the synthesis and characterization of one batch of UO{sub x} and one batch of U{sub 80}Ce{sub 20}O{sub x}. Oxide material synthesized at ORNL is being shipped to LANL for fuel fabrication process development studies. The feedstock preparation was performed using the MDD process which utilizes a rotary kiln to continuously thermally denitrate double salts of ammonium and metals to produce free-flowing powders that have good ceramic properties for fuel fabrication. Feedstock powder properties of interest include: particle size and distribution, surface area, phase purity, morphology, tap and bulk density, and flow characteristics.

modified direct denitration↗

Status of Modified Direct Denitration Development (Milestone Letter Report). MDD Status Letter Report (AFCI CETE Milestone)

Current flow sheets for processing used nuclear fuels do not produce separated streams of all of the actinides. These aqueous processing streams must be converted into solid forms suitable for recycle (fuel/target fabrication), storage, or disposal, necessitating co-conversion. A process developed at ORNL in the 1980s to make UO 3 suitable as fuel feedstock was studied for preparation of mixed actinide oxides with similarly favorable ceramic properties. The process, Modified Direct Denitration (MDD), uses ammonium nitrate to alter the thermal decomposition behavior of metal nitrates and improve the ceramic properties of the resulting solid oxide. Since plutonium (IV) and neptunium(IV) form compounds similar to uranium with the ammonium ion [(NH 4 ) 2 Pu(NO 3 ) 6 , (NH 4 ) 2 Np(NO 3 ) 6 ], MDD-conversion of these metals was considered to be applicable. Co-conversion has advantages for making mixed oxides over individual element conversions that are followed by dry mixing of the oxide powders. Issues associated with preparing a mixture from individual oxides include use of additional equipment, dusting associated with feeding and milling, time requirements for milling, blending to obtain a uniform mixture, and inhomogenity at higher plutonium concentrations. These issues can be partially or wholly avoided by using MDD coconversion in which the mixing of the individual metals occurs in liquid solution; thus, adjusting relative metal concentrations is simpler and the resulting mixed oxide is more uniform than that produced by blending the individual oxides. Utilizing MDD also eliminates the need for mechanical treatment of the powder to obtain the desired ceramic properties, such as surface area and particle size distribution, since these characteristics are acceptable as-produced. The original MDD development work established that uranium oxide with good ceramic properties could be made. Following the discovery, a more fundamental understanding of the chemistry of the uranium-ammonium double nitrate salt was developed. Later pilot-scale studies produced kilogram quantities of UO 3 using engineering-scale (1 kg/hour), continuously-operated equipment, while establishing the reliability of the process and equipment. The current work was performed in support of the Advanced Fuel Cycle Initiative (AFCI), utilizing glove-box-contained equipment (100 g/hour) to produce UO 3 , PuO 2 , and mixed oxides of uranium, plutonium, neptunium, and americium from a nitrate solution of those actinides. Then the MDD glove-box system was utilized in the Coupled-End-To-End (CETE) project to convert the U-Pu-Np and uranium product solutions into oxide powders. As part of the CETE project, a powder characterization laboratory was established in gloveboxes with instruments required for the determination of: (1) surface area by the BET methodology; (2) tap density by using a Quantachrome AutoTap; (3) flow properties by using a Freeman technology powder rheometer; (4) material composition and crystalline structure by using a powder X-ray diffractometer; (5) particle size distribution by using a laser light-scattering analyzer; and (6) imaging of the powders with a stereomicroscope. These instruments can be used to characterize the products and to determine the effects of MDD operating parameters on product powder morphology. Ultimately, the powder characteristics necessary to produce high-density, sintered MOX pellets can be determined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗