Engineering topics

Vernon, S. M.

Publications and source records attributed to Vernon, S. M..

10 records

NASA NTRS1991

Polarized-cathodoluminescence study of uniaxial and biaxial stress in GaAs/Si

The strain-induced splitting of the heavy-hole (hh) and light-hole (lh) valence bands for 4-microns thick GaAs/Si is examined on a microscopic scale using linear polarized-cathodoluminescence imaging and spectroscopy. The energies and intensities of the hh- and lh-exciton luminescence are quantitatively analyzed to determine spatial variations in the stress tensor. The results indicate that regions near and far from the microcracks are primarily subject to uniaxial and biaxial tensile stresses, respectively. The transition region where biaxial stress gradually converts to uniaxial stress is analyzed, and reveals a mixing of lh and hh characters in the strain-split bands.

Rich, D. H.↗

NASA NTRS1989

High efficiency GaAs-Ge tandem solar cells grown by MOCVD

High conversion efficiency and low weight are obviously desirable for solar cells intended for space applications. One promising structure is GaAs on Ge. The advantages of using Ge wafers as substrates include the following: they offer high efficiency by forming a two-junction tandem cell; low weight combined with superior strength allows usage of thin (3 mil) wafers; and they are a good substrate for GaAs, being lattice matched, thermal expansion matched, and available as large-area wafers.

Vernon, S. M.↗

NASA NTRS1989

Fabrication of n(+)/p InP solar cells on silicon substrates

InP films were grown by MOCVD on Si GaAs substrates (as well as on InP substrates, included as controls), and were used to fabricate solar cells, using the Spitzer et al. (1987) technique. Contact to the substrate was made with Al-Ti-Pd-Ag to the Si wafers and with Au-Zn alloy to the GaAs wafers, while contract to the front was made with Cr-Au-Ag. Air mass zero efficiencies were found to be 7.1 percent for Si-substrate cells and 9.4 percent for GaAs-substrate cells.

Keavney, C. J.↗

NASA NTRS1989

High-efficiency heteroepitaxial solar cells for space power applications

The experimental results for several technical approaches aimed at achieving highly efficient solar cells for space-power applications are reported. Efficiencies of up to 24.5 percent (170X, AM0) and 21.7 percent (1X, AM0) have been achieved with homoepitaxial GaAs p/n cells. This one-sun AM0 efficiency value is believed to be the highest reported to date. Tandem solar cells utilizing GaAs-on-Ge structures have been fabricated and shown to have efficiencies up to 21.3 percent (1X, AM0), and a GaAs-on-Si cell at 15.2 percent (1X, AM0) is reported. Homoepitaxial n/p InP cells with an efficiency of 18.8 percent (1X, AM0) are also reported. The fabrication of heteroepitaxial InP solar cells with one-sun AM0 efficiency values of 9.4 percent (on GaAs) and 7.2 percent (on Si) is described.

Vernon, S. M.↗

NASA NTRS1988

High efficiency GaAs/Ge monolithic tandem solar cells

Two-terminal monolithic tandem cells consisting of a GaAs solar cell grown epitaxially on a Ge solar cell substrate are very attractive for space applications. Tandem cells of GaAs grown by metal-organic chemical vapor deposition on thin Ge were investigated to address both higher efficiency and reduced weight. Two materials growth issues associated with this heteroepitaxial system, autodoping of the GaAs layers by Ge and diffusion of Ga and As into the Ge substrate, were addressed. The latter appears to result in information of an unintentional p-n junction in the Ge. Early simulator measurements gave efficiencies as high as 21.7 percent for 4 cm2 GaAs/Ge cells, but recent high-altitude testing has given efficiencies of 18 percent. Sources of errors in simulator measurements of two-terminal tandem cells are discussed. A limiting efficiency of about 36 percent for the tandem cell at AMO was calculated. Ways to improve the performance of present cells, primarily by increasing the Isc and Voc of the Ge cell, are proposed.

Tobin, S. P.↗

NASA NTRS1987

Indium phosphide shallow homojunction solar cells made by metalorganic chemical vapor deposition

The fabrication of highly efficient indium phosphide solar cells by metalorganic chemical vapor deposition is reported. Since InP can be annealed at temperatures at low as approximately 100 C and the annealing occurs under solar illumination itself, this accomplishment is relevant to space power systems. A total area air mass zero efficiency of 17.9 percent and an air mass 1.5 efficiency of 20.4 percent are reported. Electrical characterization identifying loss mechanisms is made, and a shallow homojunction design is discussed along with possible improvements.

Spitzer, M. B.↗

NASA NTRS1987

Status of indium phosphide solar cell development at Spire

On-going development of indium phosphide solar cells for space applications is presented. The development is being carried out with a view towards both high conversion efficiency and simplicity of manufacture. The cell designs comprise the ion-implanted cell, the indium tin oxide top contact cell, and the epitaxial cell grown by metal organic chemical vapor deposition. Modelling data on the limit to the efficiency are presented and comparison is made to measured performance data.

Spitzer, M. B.↗

NASA NTRS1986

Passivation of Si solar cells by hetero-epitaxial compound semiconductor coatings

A development status evaluation is made for high efficiency Si solar cells, with emphasis on the suppression of the deleterious effects of surface recombination. ZnS(0.9)Se(0.1) and GaP are identified as candidates for the reduction of surface recombination. Attention is given to methods developed for the deposition of heteroepitaxial compounds designed to block minority carrier transport to the Si solar cell surface without interfering with the majority carrier flow.

Vernon, S. M.↗

NASA NTRS1984

Development of GaAs/Si and GaAs/Si monolithic structures for future space solar cells

The results of heteroepitaxial growth of GaAs and GaAlAs directly on Si are presented, and applications to new cell structures are suggested. The novel feature is the elimination of a Ge lattice transition region. This feature not only reduces the cost of substrate preparation, but also makes possible the fabrication of high efficiency monolithic cascade structures. All films to be discussed were grown by organometallic chemical vapor deposition at atmospheric pressure. This process yielded reproducible, large-area films of GaAs, grown directly on Si, that are tightly adherent and smooth, and are characterized by a defect density of 5 x 10(6) power/sq cm. Preliminary studies indicate that GaAlAs can also be grown in this way. A number of promising applications are suggested. Certainly these substrates are ideal for low-weight GaAs space solar ells. For very high efficiency, the absence of Ge makes the technology attractive for GaAlAs/Si monolithic cascades, in which the Si substrates would first be provided with a suitable p/n junction. An evaluation of a three bandgap cascade consisting of appropriately designed GaAlAs/GaAs/Si layers is also presented.

Spitzer, M. B.↗

NASA NTRS1982

Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures

The power to weight ratio of GaAs cells can be reduced by fabricating devices using thin GaAs films on low density substrate materials (silicon, glass, plastics). A graphoepitaxy technique was developed which uses fine geometric patterns in the substrate to affect growth. Initial substrates were processed by etching 25 microns deep grooves into 100 oriented wafers; fine-grained polycrystalline GaAs layers 25-50 microns thick were then deposited on these and recrystallization was performed, heating the substrates to above the GaAs melting point in ASH3 atmosphere, resulting in large grain regrowth oriented along the groove dimensions. Experiments with smaller groove depths and spacings were initially encouraging; single large GaAs grains would totally cover one and often two groove fields of 14 groove each spanning several hundred microns. Dielectric coatings on the grooved substrates were also used to modify the growth.

Hovel, H. J.↗