Engineering topics

Verzemnieks, Juris

Publications and source records attributed to Verzemnieks, Juris.

5 records

NASA NTRS2002

Advanced High Temperature Structural Seals

This program addresses the development of high temperature structural seals for control surfaces for a new generation of small reusable launch vehicles. Successful development will contribute significantly to the mission goal of reducing launch cost for small, 200 to 300 pound payloads. Development of high temperature seals is mission enabling. For instance, ineffective control surface seals can result in high temperature (3100 F) flows in the elevon area exceeding structural material limits. Longer sealing life will allow use for many missions before replacement, contributing to the reduction of hardware, operation and launch costs.

Newquist, Charles W.↗

NASA NTRS2001

Further Investigations of Control Surface Seals for the X-38 Re-Entry Vehicle

NASA is currently developing the X-38 vehicle that will be used to demonstrate the technologies required for a potential crew return vehicle (CRV) for the International Space Station. This vehicle would serve both as an ambulance for medical emergencies and as an evacuation vehicle for the Space Station. Control surfaces on the X-38 (body flaps and rudder/fin assemblies) require high temperature seals to limit hot gas ingestion and transfer of heat to underlying low-temperature structures to prevent over-temperature of these structures and possible loss of the vehicle. NASAs Johnson Space Center (JSC) and Glenn Research Center (GRC) are working together to develop and evaluate seals for these control surfaces. This paper presents results for compression. flow, scrub, and arc jet tests conducted on the baseline X-38 rudder/fin seal design. Room temperature seal compression tests were performed at low compression levels to determine load versus linear compression, preload. contact area, stiffness. and resiliency characteristics under low load conditions. For all compression levels that were tested, unit loads and contact pressures for the seals were below the 5 lb/in. and 10 psi limits required to limit the loads on the adjoining Shuttle thermal tiles that the seals will contact. Flow rates through an unloaded (i.e. 0% compression) double arrangement were twice those of a double seal compressed to the 20% design compression level. The seals survived an ambient temperature 1000 cycle scrub test over relatively rough Shuttle tile surfaces. The seals were able to disengage and re-engage the edges of the rub surface tiles while being scrubbed over them. Arc jet tests were performed to experimentally determine anticipated seal temperatures for representative flow boundary conditions (pressures and temperatures) under simulated vehicle re-entry conditions. Installation of a single seat in the gap of the test fixture caused a large temperature drop (1710 F) across the seal location as compared to an open gap condition (140 F) confirming the need for seals in the rudder/fin gap location. The seal acted as an effective thermal barrier limiting heat convection through the seal gap and minimizing temperature increases downstream of the seal during maximum heating conditions.

Dunlap, Patrick H., Jr.↗

NASA NTRS2000

Advanced High Temperature Structural Seals

This program addresses the development of high temperature structural seals for control surfaces for a new generation of small reusable launch vehicles. Successful development will contribute significantly to the mission goal of reducing launch cost for small, 200 to 300 lb payloads. Development of high temperature seals is mission enabling. For instance, ineffective control surface seals can result in high temperature (3100 F) flows in the elevon area exceeding structural material limits. Longer sealing life will allow use for many missions before replacement, contributing to the reduction of hardware, operation and launch costs. During the first phase of this program the existing launch vehicle control surface sealing concepts were reviewed, the aerothermal environment for a high temperature seal design was analyzed and a mock up of an arc-jet test fixture for evaluating seal concepts was fabricated.

Newquist, Charles W.↗

NASA NTRS1992

Survey of results from the Boeing modules on the M0003 experiment on LDEF

The Boeing Company provided specimens to be flown on the Long Duration Exposure Facility (LDEF) as part of the M0003 experiment. This hardware was for the M0003-8 and part of the M003-10 sub-experiments. These specimens were flown on the leading (tray D-9) and trailing (tray D-3) edges, and on trays D-8 (38 degrees from ram) and D-4. Some specimens were mounted in the Experiment Exposure Control Canisters.

Pippin, H. Gary↗

NASA NTRS1991

Survey of results from the Boeing modules on the M0003 experiment on LDEF

The Boeing modules on the M0003 experiment included fiber optics, ceramic materials, a variety of electronic piece parts, composites and thermal control paints, fasteners, thin film lubricants, anodized surfaces, and adhesives. These materials were flown on the leading and trailing edge exteriors, and on the interior portion of LDEF M0003 providing exposure under three distinct environments. The condition of each of these material types is described. Results of optical, surface, and mechanical properties are presented.

Pippin, H. Gary↗