Engineering topics
Vianco, Paul Thomas
Publications and source records attributed to Vianco, Paul Thomas.
Sensitivity of Copper Dissolution to the Flow Behavior of Molten Sn-Pb Solder.
Abstract not provided.
Ag-Au-Ge alloys for high temperature geothermal and oil well electronics applications.
Abstract not provided.
Ag-Au-Ge alloys for high temperature geothermal and oil well electronics applications.
Abstract not provided.
Computational modeling : on the critical path for predicting solder joint reliability.
No abstract prepared.
Harsh environments electronics : downhole applications.
The development and operational sustainment of renewable (geothermal) and non-renewable (fossil fuel) energy resources will be accompanied by increasingly higher costs factors: exploration and site preparation, operational maintenance and repair. Increased government oversight in the wake of the Gulf oil spill will only add to the cost burden. It is important to understand that downhole conditions are not just about elevated temperatures. It is often construed that military electronics are exposed to the upper limit in terms of extreme service environments. Probably the harshest of all service conditions for electronics and electrical equipment are those in oil, gas, and geothermal wells. From the technology perspective, advanced materials, sensors, and microelectronics devices are benefificial to the exploration and sustainment of energy resources, especially in terms of lower costs. Besides the need for the science that creates these breakthroughs - there is also a need for sustained engineering development and testing. Downhole oil, gas, and geothermal well applications can have a wide range of environments and reliability requirements: Temperature, Pressure, Vibration, Corrosion, and Service duration. All too frequently, these conditions are not well-defifined because the application is labeled as 'high temperature'. This ambiguity is problematic when the investigation turns to new approaches for electronic packaging solutions. The objective is to develop harsh environment, electronic packaging that meets customer requirements of cost, performance, and reliability. There are a number of challenges: (1) Materials sets - solder alloys, substrate materials; (2) Manufacturing process - low to middle volumes, low defect counts, new equipment technologies; and (3) Reliability testing - requirements documents, test methods and modeling, relevant standards documents. The cost to develop and sustain renewable and non-renewable energy resources will continue to escalate within the industry. Downhole electronics can provide a very cost-effective approach for well exploration and sustainment (data logging). However, the harsh environments are a 'game-changer' in terms defining materials, assembly processes and the long-term reliability of downhole electronic systems. The system-level approach will enable the integration of each of these contributors - materials, processes, and reliability - in order to deliver cost-effective electronics that meet customer requirements.
New Guideline Highlights Hand Soldering as an Engineering Technology.
Abstract not provided.
TurboSIP - Solder Interconnect Predictor : a class for new users.
No abstract prepared.
Solderability testing of electroless nickel-electroless palladium-immersion gold.
No abstract prepared.
A constitutive model for Sn-Pb solder.
A unified creep plasticity damage (UCPD) model for Sn-Pb solder is developed in this paper. Stephens and Frear (1999) studied the creep behavior of near-eutectic 60Sn-40Pb solder subjected to low strain rates and found that the inelastic (creep and plastic) strain rate could be accurately described using a hyperbolic Sine function of the applied effective stress. A recently developed high-rate servo-hydraulic method was employed to characterize the temperature and strain-rate dependent stress-strain behavior of eutectic Sn-Pb solder over a wide range of strain rates (10{sup -4} to 10{sup 2} per second). The steady state inelastic strain rate data from these latest experiments were also accurately captured by the hyperbolic Sine equation developed by Stephens and Frear. Thus, this equation was used as the basis for the UCPD model for Sn-Pb solder developed in this paper. Stephens, J.J., and Frear, D.R., Metallurgical and Materials Transactions A, Volume 30A, pp. 1301-1313, May 1999.
Pull strength and failure mode analysis of thick film conductors on alumina ceramic for hybrid microcircuit technologies.
No abstract prepared.
Temperature cycling of Pb-free and mixed solder interconnections used on a package-on-package test vehicle.
Abstract Not Provided
Age-aware solder performance models : level 2 milestone completion.
Legislated requirements and industry standards are replacing eutectic lead-tin (Pb-Sn) solders with lead-free (Pb-free) solders in future component designs and in replacements and retrofits. Since Pb-free solders have not yet seen service for long periods, their long-term behavior is poorly characterized. Because understanding the reliability of Pb-free solders is critical to supporting the next generation of circuit board designs, it is imperative that we develop, validate and exercise a solder lifetime model that can capture the thermomechanical response of Pb-free solder joints in stockpile components. To this end, an ASC Level 2 milestone was identified for fiscal year 2010: Milestone 3605: Utilize experimentally validated constitutive model for lead-free solder to simulate aging and reliability of solder joints in stockpile components. This report documents the completion of this milestone, including evidence that the milestone completion criteria were met and a summary of the milestone Program Review.
Temperature cycling of PB-free and mixed solder interconnections used on a package-on-package test vehicle.
No abstract prepared.
Understanding and predicting metallic whisker growth and its effect on reliability (LDRD research).
No abstract prepared.
The challenges of Pb-free electronics technology facing the Aerospace and Defense (A&D) industries : %22Beyond the Solder Joint.%22
No abstract prepared.