Search NASA⌕ Search

Engineering topics

Vinay Goyal

Publications and source records attributed to Vinay Goyal.

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Treatment of Transient Pressure Events in Space Flight Pressurized Systems

A multi-disciplinary team from the NASA Engineering and Safety Center (NESC) and The Aerospace Corporation developed a roadmap on how to treat transients in spaceflight pressurized systems. This document presents a focused discussion on the topic of pressure transients for consideration within the aerospace community.

NASA Engineering and Safety Center↗
NASA NTRS2021

Arecibo Observatory Auxiliary M4N Socket Termination Failure Investigation

The NASA Engineering and Safety Center (NESC) was requested to support the Arecibo Observatory failure investigation in determining the root cause of the Auxiliary M4N cable failure. The NESC and Kennedy Space Center led an integrated NASA investigation with support from Marshall Space Flight Center and The Aerospace Corporation that included forensic investigation of failed hardware, finite element modeling, materials characterization, and root cause analysis. This document contains the outcome of the NESC Assessment.

Zinc Spelter Sockets↗
NASA NTRSDate not supplied

Treatment of Transient Pressure Events in Space Flight Pressurized Systems

The general physics of pressure transients, sources of pressure transients, and major factors influencing pressure transients are addressed. Mitigation strategies that aid in reducing the magnitude of pressure transients are discussed. Methods to characterize pressure transients and their effects on the structure are presented. Case studies illustrate the structural analysis methodology used to predict the structural dynamic response. The structural verification process involves formulating acceptance and qualification programs, which requires knowledge of the stress state. The maximum expected operating pressure (MEOP) is established such that the maximum stress produced by static pressure is equivalent to the maximum stress at the same critical location produced by the combined effect of steady state pressure and the magnitude of the pressure transient. A roadmap on how to treat transient pressures in the structural verification process of spaceflight pressurized systems (e.g., valves, lines, pressure vessels, pressurized structures) is presented.

Transient Pressure Events↗
NASA NTRSDate not supplied

Best Practices, Lessons Learned, and Examples on the Application of Damage Tolerance in Space Structures

Damage tolerance is an important consideration in space structures applications. The intent of damage tolerance is to demonstrate that the structure is robust to the presence of flaws over the service life of the space vehicle. Damage tolerance requirements in documents such as those in NASA, AIAA, and ISO can be challenging to implement. The intent of this paper is three-fold: (1) Provide best practices in the application of damage tolerance requirements for space applications, (2) Provide lessons learned for each of class of hardware, (3) Provide examples of challenging situations encountered in the application of damage tolerance. Examples cover additive manufacturing, composite overwrapped pressure vessels, pressurized structures, liquid rocket engines, thermal protection systems, and other classes of hardware. The philosophy and limitations of leak before burst and proof test logic are also discussed. Finally, a discussion on elastic-plastic fracture mechanics with comparisons to test data will be presented.

Best Practices↗
NASA NTRSDate not supplied

Structural Analysis Findings of Open Spelter Socket Cable Terminations

A three-dimensional nonlinear finite element model of a representative open spelter socket termination was developed to examine the underlying mechanics of load transfer from a structural cable through the termination, the sensitivity of the joint design to wire brooming, zinc material nonlinearity, contact friction between the zinc and socket, voids within the zinc, and, finally, the effects of repeated loading on the joint. Primary factors affecting open spelter socket design are cast zinc plastic flow, depth of zinc slug seating, and quality of wire brooming. Zinc plasticity and proper brooming allows for efficient load transfer by developing confining pressure on the broomed wires in the narrow part of the socket, which keep the wires from pulling out of the zinc and shift failure to occur outside the socket. Highest wire stresses in the cable occur in the outer ring adjacent to the termination. While industry use of stay cables are typically designed to carry less than half the rated breaking force in aggregate, the constituent stresses within the zinc and the wires have the potential to exceed their respective allowable in operation and should be evaluated for fatigue- and creep-critical applications.

Pavel Babuska↗
NASA NTRSDate not supplied

Lessons Learned from the Arecibo Observatory Auxiliary M4N Socket Analysis and Implications for Future Observatory Designs

The Arecibo Observatory collapsed after a progressive structural failure stemming from the failure of a single socket joint cable termination. A failure investigation was conducted to identify the cause of the first failed cable termination socket. Due to the nature of the suspended observatory receiver, the dominant source of loading in the suspension cables was due to deadload, with secondary contributions coming from environmental effects and observatory operation. The high ratio of deadload vs. live load applied to the cable over many years resulted in a creep failure mode of the cast zinc within the socket which further induced stress into the highly stress wires at the entrance of the socket. The design of the socket joint did not explicitly consider socket constituent stress margins and time-dependent damage mechanisms such as creep. Lessons learned from this investigation led to recommendations for revising civil engineering cable standards, and recommendations for manufacturers and designers. The design of cables employing socket terminations should consider the cumulative damage effects from creep and cyclic loading identify their corresponding worst-case inspectable defects or establish a sufficiently high factor of safety so that the design is sufficiently robust to defects and time-dependent failure modes. The design should specify end-of-life capability and set service life inspection intervals with pass/fail inspection criteria. Finally, trial studies on design iterations were conducted to increase the reliability of cables with socket joints.

Pavel Babuska↗
NASA NTRSDate not supplied

Novel Test and Analysis Methodology for the Assessment of Joint under Re-entry Environment

Spacecraft thermal protection systems require unique approaches for design verification due to the extreme environments seen during space travel and atmospheric re-entry. In this work, unique considerations for design, analysis, and verification of a tiled heatshield design with material nonlinearity, material property temperature-dependency, material property rate-dependency, and geometric stress concentrations are presented. Such designs require a thorough application of the building block approach to derive appropriate material property datasets, and a novel application of analysis models to aid in the structural verification with testing. The custom application of material rate-dependency in finite element analysis software is presented as a means of leveraging the rate-dependent test data for the material property dataset. Because bonded tile heatshields contain so many design considerations and nonlinearities which often preclude the ability to easily achieve the requisite test factors in qualification testing, a novel sub-element test was developed that amplifies the stress singularity beyond flight conditions. The test achieves an over-test over flight stress conditions. The approach for sub-element coupon design can be extended to other bonded joint designs and can be used in aiding a qualification program.

Pavel Babuska↗
NASA NTRSDate not supplied

Reliability-Based Damage Tolerance Framework for Achieving Highly Reusable Launch Systems

The United States Space Force and NASA are exploring approaches that enable rapid launch response via highly reusable launch systems. One hindrance to achieving high reusability is the inability to meet damage tolerance requirements. To this end, a framework for applying reliability-based damage tolerance to space structures is presented. The reliability-based approach employs probabilistic distributions of key input variables such as material properties, geometry, loads, inspection probability, and defect characteristics to predict hardware reliability for the planned mission life. The probabilistic variables needed to perform the reliability assessments are defined and recommendations on how to collect the required data are provided. Several example problems illustrate the implementation and execution of this approach.

Leland Shimizu↗
NASA NTRSDate not supplied

Proposed Reliability-Based Damage Tolerance Guidelines for Space Systems

Deterministic damage tolerance guidelines for highly reusable and efficiently designed launch systems can be challenging to meet and result in overly conservative assessments for tightly controlled manufacturing processes. Deterministic approaches may be unconservative when the structure is workmanship sensitive and there is a wide spread in fracture properties. Reliability-based damage tolerance assessments targeting a component reliability over the service life commensurate to mission risk posture is a promising alternative. Low production rates, short fleets, and lack of standards or guidance has slowed down widespread adoption of this method. Guidance for the robust application of reliability-based damage tolerance for space systems are proposed. These guidelines cover the treatment of uncertainty in damage tolerance analysis, the collection of data to develop probabilistic distributions, uncertainty propagation methods, and types of hardware.

Reliability-Based Damage Tolerance↗
NASA NTRSDate not supplied

Toward a Fully Capable In-Space Manufacturing Ecosystem

As technology for in-space refueling and servicing continues to mature, in-space assembly and manufacturing efforts can expand to leverage these new capabilities. This paper expands upon previous work and describes four use cases for a fully capable in-space manufacturing ecosystem. Based on those use cases, enabling technology areas are identified and shortfalls in those technologies are noted for seven key categories. Finally, a survey of options for in-space experiments and demonstrations are presented, showing pathways for technology development in relevant environments.

in-space manufacturing ecosystem↗