Reaction engineering of the hydrogenolysis of liquid n-Alkanes: Comparison of flow and batch reaction systems
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Engineering topics
Vohs, John M.
Publications and source records attributed to Vohs, John M..
Modulating the Contact Angle between Nonpolar Polymers and SiO 2 Nanoparticles
Polymer–nanoparticle interactions play an important role in determining the morphology and properties of polymer nanocomposites and controlling the polymeric reactions involving heterogeneous catalysts. Here, in this study, we modulate the interactions between nonpolar polymers and nanoparticles by modifying the nanoparticle surface chemistry and quantify the interaction strength through direct contact angle measurements. We investigate the interactions of three nonpolar polymers, polystyrene, polyethylene, and polycyclooctene, with silica nanoparticles whose surface chemistry has been modified by atomic layer deposition of titania and calcium carbonate and by alkyl silanization. Significant differences in polymer–nanoparticle interactions are observed, which can be attributed to differences in the polarizability of the polymers and oxide surface composition. Compared to fully hydrogenated polycyclooctene, polycyclooctene is shown to have stronger interactions with most metal oxides; however, this trend is reversed following alkyl silanization of the silica nanoparticles, which makes the surface of the particles less polar. These differences in interactions can be leveraged to make polymer nanocomposites with unique properties and enable the selective conversion of polymers without the need for separations.
36 MATERIALS SCIENCE↗
Stabilization of Ni-YSZ Anodes in Solid Oxide Fuel Cells using an ALD-Grown Aluminum Titanate Interlayer
The effect of an Al 2 TiO 5 (ALT) interlayer between Ni and YSZ on enhancing the thermal stability of Ni-YSZ solid oxide fuel cell was examined. Atomic layer deposition (ALD) was used to provide precise control of the structure and thickness of the ALT interlayer. The study's findings demonstrate that a 2 nm thick ALT interlayer deposited by ALD does not adversely affect the cell's ohmic resistance and effectively prevents Ni sintering and the loss of active area during high-temperature heat treatments. ALT layers thicker than 2 nm, although they enhanced Ni stability, were found to impede oxygen ion transport in the electrode and significantly increase the ohmic resistance of the cell, leading to a decline in performance.
25 ENERGY STORAGE↗
Determination of film thicknesses of metal oxides prepared by atomic layer deposition on SBA-15
ZrO 2 and CeO 2 films were grown in SBA-15 by Atomic Layer Deposition (ALD) to loadings of 0.92 g oxide/g SBA-15. Scanning Transmission Electron Microscopy (STEM) with Energy Dispersive Spectra (EDS) showed that the oxides grew uniformly inside the mesopores. Film thicknesses were then analyzed as a function of the number of ALD cycles using three methods: 1) mass changes assuming bulk densities for the films; 2) changes in pore size from Barret-Joyner-Halenda (BJH) analysis with N 2 adsorption isotherms; and 3) small-angle X-ray scattering (SAXS). Film thicknesses assuming bulk densities were between 6 and 8 times smaller than those obtained from BJH analysis. SAXS analysis gave film thicknesses that were approximately twice that obtained from bulk densities. Here, possible explanations of the discrepancies between these methods are discussed.
36 MATERIALS SCIENCE↗
Hydrodeoxygenation of m -Cresol over WO x -Pt/SBA-15 Using Alkanes as Hydrogen Carriers
Not provided.
Chemistry↗
Hydrogenolysis of n -eicosane over Ru-based catalysts in a continuous flow reactor
The hydrogenolysis of n-eicosane (C 20 H 42 ) was studied under differential conditions over Ru-based catalysts including Ru/SiO 2 , Ru/TiO 2 , and Ru/SBA-15, using a continuous flow reactor that was specially designed for large hydrocarbon reactants that are solids at room temperature. Similar rates and product distributions were obtained for Ru/SiO 2 and Ru/SBA-15 at 433 K, with the most abundant products being C 1 and C 19 hydrocarbons and smaller amounts of C 8 to C 18 also being produced. The higher yield of C 1 and C 19 indicates that cleavage of the terminal C-C bond is somewhat more facile than an internal C-C bond. At 473 K the product distribution shifted to mostly C 1 suggesting that, at this temperature, the adsorbed alkyl fragments undergo complete C-C bond scission prior to desorbing. Here, the conversion was also found to be inversely proportional to the H 2 pressure. Similar results were obtained for Ru/TiO 2 except this catalyst was found to be less active than both Ru/SiO 2 and Ru/SBA-15.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A Study of Support Effects for the Water-Gas-Shift Reaction over Cu
The water–gas-shift (WGS) reaction was studied on a series of supported Cu catalysts in which the MgAl 2 O 4 (MAO) support was modified by depositing ZnO, CeO 2 , Mn2O 3 and CoO using Atomic Layer Deposition (ALD). Addition of Cu by one ALD cycle gave rise to catalysts with nominally 1-wt% Cu. A 1.1-wt% Cu/MAO catalyst prepared by ALD exhibited twice the dispersion but ten times the WGS activity of a 1-wt% Cu/MAO catalyst prepared by impregnation, implying that the reaction is structure sensitive. However, Cu catalysts prepared with the ZnO, CeO 2 , and Mn 2 O 3 films showed negligible differences from that of the Cu/MAO catalyst, implying that these oxides did not promote the reaction. Cu catalysts prepared on the CoO film showed a slightly lower activity, possibly due to alloy formation. The implications of these results for the development of better WGS catalysts is discussed.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Site and Structural Requirements for the Dehydra-Decyclization of Cyclic Ethers on ZrO2
In this study, we examined the site and structural requirements for the dehydra-decyclization of cyclic ethers, tetrahydrofuran, and tetrahydropyran to produce conjugated dienes over ZrO2-based catalysts, a reaction that could be an important step in the use of biomass-derived sugars as a starting material to produce monomers for the plastics industry. To help identify the active sites for this reaction, studies were conducted in which ZrO2 surfaces were decorated with Na. These studies showed that Na was effective at poisoning the activity for the ring opening of cyclic ethers, but much less so for the dehydration of the resulting adsorbed alkoxides. The studies of the activity of different types of ZrO2 for the dehydra-decyclization reaction, including single crystals and ultra-thin films supported on MgAl2O4 and silica, also showed that the reaction was dependent on the local structure of the ZrO2 surface. The insights these results provide for identifying the active sites on the ZrO2 surface are discussed.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A Study of How LaFeO 3 and CaTiO 3 Supports Affect the Oxidation, Hydrogenation, and Methane Steam Reforming Activity of Pt and Ni Catalysts
The structure and catalytic properties of Pt and Ni supported on thin films of LaFeO 3 and CaTiO 3 , prepared by Atomic Layer Deposition (ALD), were investigated. X-Ray diffraction (XRD) and scanning transmission electron microscopy (STEM) show that reduction at 1073 K causes Pt-Fe intermetallic compound formation for Pt/LaFeO 3 . For Pt/CaTiO 3 , 1073-K reduction induces local decomposition of the CaTiO 3 with migration of Ti to the Pt. Reduced Pt/LaFeO 3 and Pt/CaTiO 3 exhibited CO-oxidation activity similar to that for Pt supported on MgAl 2 O 4 but were much less active for propane oxidation and hydrogenation of 1-hexene and toluene. In contrast, Ni/CaTiO 3 behaved similarly to a conventional supported Ni catalyst for the methane-steam-reforming (MSR) and 1-hexene hydrogenation. There was also no evidence for local decomposition of the perovskite in the vicinity of the Ni particles. Furthermore, the results obtained in this study demonstrate that metal-perovskite interactions that affect reactivity are specific to each component.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Flexible atomic layer deposition system for coating porous materials
In this paper, we describe an atomic layer deposition (ALD) system that is optimized for the growth of thin films on high-surface-area, porous materials. The system incorporates a moveable dual-zone furnace allowing for rapid transfer of a powder substrate between heating zones whose temperatures are optimized for precursor adsorption and oxidative removal of the precursor ligands. The reactor can both be evacuated, eliminating the need for a carrier gas during precursor exposure, and rotated, to enhance contact between a powder support and the gas phase, both of which help us to minimize mass transfer limitations in the pores during film growth. The capabilities of the ALD system were demonstrated by growing La 2 O 3 , Fe 2 O 3 , and LaFeO 3 films on a 120 m 2 g -1 MgAl 2 O 4 powder. Analysis of these films using scanning transmission electron microscopy and temperature-programmed desorption of 2-propanol confirmed the conformal nature of the oxide films.
36 MATERIALS SCIENCE↗
Synthesis of high-surface area tungstated zirconia by atomic layer deposition on mesoporous silica
Atomic layer deposition (ALD) was used to prepare ZrO 2 films on the surface of the mesoporous silica, SBA-15, and to modify the surface of these films with WO 3 in order to form tungstated zirconia. Adsorption-desorption isotherms, pore size distributions, and transmission electron microscopy demonstrated that the ALD synthesis produced zirconia films that were conformal to the SBA-15 pores. DRIFT spectroscopy of pyridine adsorbed on the tungstated-zirconia SBA-15 samples showed adsorbed pyridinium ions, confirming the presence of Brønsted-acid sites on this material, consistent with what has been reported for bulk tungstated zirconia. Here, the ALD-synthesized, tungstated-zirconia SBA-15 was also shown to be active in the acid-catalyzed H-D exchange between toluene and D 2 O.
Brønsted acid site↗
An Investigation of the Electrochemical Activity of (Ba/Sr)FeO 3-y Anodes
FeO x , SrFeO 3-y (SF), and Ba 0.5 Sr 0.5 FeO 3–y (BSF) were studied for application as fuel oxidation catalysts in solid oxide fuel cells (SOFC) anodes. Electrodes were prepared by impregnation into porous yttria-stabilized zirconia (YSZ), with La 0.3 Sr 0.7 TiO 3–y (LST) added for electronic conductivity. The electrode impedances decreased dramatically upon addition of SF and BSF and much less when only SrO or FeO x were added. Temperature Programmed Desorption (TPD) of O 2 from oxidized BSF showed O 2 desorbing between 200 °C and 700 °C, while no O 2 desorbed from Fe 2 O 3 below 900 °C. The results, together with thermodynamic analysis, suggest that stabilization of Fe +4 in the perovskite lattice plays an important role in enhancing the catalytic activity of SF and BSF by providing access to a Fe 3+ /Fe 4+ redox couple that can accept oxygen anions from the yttria-stabilized zirconia (YSZ) electrolyte. Oxygen is weakly bound to these sites facilitating its reaction with adsorbed H 2 .
Electrochemistry↗
Furfural Upgrading by Aldol Condensation with Ketones over Solid-Base Catalysts
Aldol condensation reactions between furfural and various ketones were studied in a flow reactor at 373 K and 100 psi for application to upgrading of furfural. Specific rates for the reaction of acetone and furfural were measured on MgAl 2 O 4 , Al 2 O 3 , CaO/MgAl 2 O 4 and MgO/MgAl 2 O 4 and found to be highest on CaO/MgAl 2 O 4 . While the presence of CO 2 and H 2 O did not affect the stability of the CaO/MgAl 2 O 4 catalyst, the catalyst deactivated over a period of a few hours due to the production of 2-furoic acid formed by the Cannizzaro reaction. While aldol condensation rates between furfural and either 2-pentanone and decanal approached that of acetone, rates for 4-heptanone and 2,5-heptanedione were significantly lower because the α-hydrogens of the carbonyl compounds are less easily attacked in these molecules. The selectivity to aldol products is affected by the relative rates of the aldol-condensation and the Cannizzaro reactions. Possible strategies for maximizing production of the aldol products with larger ketones are discussed.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Evidence for redispersion of Ni on LaMnO 3 films following high-temperature oxidation
LaMnO 3 films, 0.5-nm thick, were deposited by atomic layer deposition (ALD) onto γ-Al 2 O 3 that had been modified with 15-wt% CaO. The CaO was shown to be effective in preventing formation of LaAlO 3 that formed when La 2 O 3 was deposited directly onto γ-Al 2 O 3 . Lattice fringes on the resulting CaAl 2 O 4 /γ-Al 2 O 3 substrate were weakly resolved, allowing a detailed characterization of the LaMnO 3 films. High-resolution transmission electron microscopy (HR-TEM) images showed that the LaMnO 3 formed two-dimensional crystallites, ~10 to 15 nm wide, that covered most of the surface. Crystallites with (001) and (111) orientation were clearly identified. High-temperature oxidation caused Ni to spread over the LaMnO 3 film, suggesting there is a reaction of the Ni 2+ cations with the perovskite lattice. Ni formed by high-temperature reduction on these films remained well dispersed and significantly more active for CO 2 reforming of CH 4 compared to Ni on MgAl 2 O 4 , even after repeated oxidation and reduction cycles at 1073 K. Finally, the implications of these results for understanding metal-support interactions between Ni and LaMnO 3 are discussed.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]
The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.
30 DIRECT ENERGY CONVERSION↗
Enhancing Coking Tolerance and Stability of SOFC Anodes Using Atomic Layer Deposition (ALD) of Oxide Thin Films
The overall objective of this project was to use atomic layer deposition (ALD) to add modifiers to the surfaces of conventional Ni-YSZ cermet, solid oxide fuel cell (SOFC) anodes to enhance both their tolerance to hydrocarbon fuels by decreasing their propensity to form coke deposits, and to increase redox stability. Studies of the use of ALD to modify analogous supported metal powder catalysts were also added to the scope of the project in response to our industrial partner, Atrex going out of business. The initial portion of the program focused on designing and building the ALD reactor required for deposition of the oxide modifier films. Studies of the oxide modifier films on the coking tolerance and of redox properties of Ni-cermet anodes were then carried out. These studies demonstrated that while surface oxide modifiers were able to impart some coking resistance this only occurred for a relatively small range of operating conditions (e.g., temperature, steam-to-fuel ratio, etc.) and not at the level that would be required for operating in methane fuel at low steam-to-methane ratios. In light of this observation, we focused on assessing another approach to enhance anode coking resistance which eliminated bulk Ni from the anode. This approach made use of electronically conducting perovskite films to provide electrical conductivity in the anode, while using small amounts of Ni or other metals, such as Pt, deposited using ALD as the anode oxidation catalyst. This approach proved to be quite promising at both imparting coking resistance and redox stability.
03 NATURAL GAS↗
Dry reforming of methane over Ni supported on LaMnO 3 thin films
Thin films of LaMnO 3 were deposited onto MgAl 2 O 4 by Atomic Layer Deposition (ALD) and studied as supports for Ni in the Dry Reforming of Methane (DRM). Scanning Transmission Electron Microscopy (STEM) with Energy-Dispersive X-ray Spectroscopy (EDS) demonstrated that LaMnO 3 covered the support uniformly, and X-ray diffraction (XRD) showed that the LaMnO 3 films maintained their perovskite structure after 5 redox cycles at 1073 K. The Ni also remained well dispersed after 5 redox cycles at 1073 K. The LaMnO 3 -supported catalyst was more active than Ni on the unmodified MgAl 2 O 4 and showed superior resistance against coke formation. Lastly, the results for Ni on the LaMnO 3 films are compared to previous results for Ni on LaFeO 3 , CaTiO 3 , SrTiO 3 , and BaTiO 3 films.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Investigating the Catalytic Requirements of Perovskite Fuel Electrodes Using Ultra-Low Metal Loadings
Solid Oxide Fuel Cells (SOFC) with La 0.3 Sr 0.7 TiO 3 (LST)–yttria-stabilized ZrO 2 (YSZ) anodes were prepared by impregnation of LST into porous YSZ scaffolds and then modified by Atomic Layer Deposition (ALD) of Ni, Pt, Pd, Fe, Co. and CeO 2 . Weight loadings as low as 0.01% of Pt, Ni, and Pd were sufficient to decrease anode impedances by orders of magnitude for operation in humidified H 2 at 973 K. The effects of CeO 2 , Co, and Fe were less but still significant. Sintering at higher temperatures was important. Furthermore, possible ways of stabilizing the metal particles and implications for developing ceramic anodes are discussed.
25 ENERGY STORAGE↗