Engineering topics

Volz, M. P.

Publications and source records attributed to Volz, M. P..

At least 55 records · Page 3

NASA NTRS2008

New Scintillator Materials (K2CeBr5) and (Cs2CeBr5)

Cesium cerium bromide (Cs2CeBr5) and potassium cerium bromide (K2CeBr5) are new scintillator materials for X-ray and gamma ray detector applications. Recently halide scintillator materials, such as Ce doped lanthanum bromide has been proved to be very important material for the same purpose. These materials are highly hygroscopic; a search for high light yield non-hygroscopic materials was highly desirable to advance the scintillator technology. In this paper, we are reporting the crystal growth of novel scintillator materials, cesium cerium bromide (Cs2CeBr5) and potassium cerium bromide (K2CeBr5). Crystals were successfully grown from the melt using the vertical Bridgman-Stockbarger technique, in a comparison with the high performance LaBr3 or LaCl3 crystals, cerium based alkali halides crystals, (Cs2CeBr5) and (K2CeBr5) have similar scintillation properties, while being much less hygroscopic. Furthermore, cesium based compounds will not suffer from the self-activity present in potassium and lanthanum compounds. However the Cs2CeBr5 crystals did not grow properly probably due to non-congruent melting or to some phase transition during cooling. Keywords." Scintillator materials; Ce3+; Energy resolution; Light yield; K2CeBr5

Hawrami, R.↗

NASA NTRS2008

Interface Shape Control Using Localized Heating during Bridgman Growth

Numerical calculations were performed to assess the effect of localized radial heating on the melt-crystal interface shape during vertical Bridgman growth. System parameters examined include the ampoule, melt and crystal thermal conductivities, the magnitude and width of localized heating, and the latent heat of crystallization. Concave interface shapes, typical of semiconductor systems, could be flattened or made convex with localized heating. Although localized heating caused shallower thermal gradients ahead of the interface, the magnitude of the localized heating required for convexity was less than that which resulted in a thermal inversion ahead of the interface. A convex interface shape was most readily achieved with ampoules of lower thermal conductivity. Increasing melt convection tended to flatten the interface, but the amount of radial heating required to achieve a convex interface was essentially independent of the convection intensity.

Volz, M. P.↗

NASA NTRS2006

Hydrogen Reduction of Ilmenite from Lunar Regolith

Each ascent vehicle returning from the lunar surface with a crew vehicle will require several tons of fuel. Most architecture studies of lunar exploration vehicles use liquid oxygen for fuel, either for LOX/LH2 or LOX/methane. Utilization of oxygen generated on the lunar surface saves mass launched from Earth, with a multiplication factor on the order of 4-5, e.g. production and utilization of 4 tons of lunar oxygen for the ascent vehicle saves 16-20 tons of initial mass in low Earth orbit (IMLEO). The paper discusses ongoing MSFC activity on oxygen production by hydrogen reduction of Ilmenite. Specifically the important project milestone is to develop the Technology Readiness Level for the generation of lunar oxygen for propellant production from 3 to 5. The paper will provide an overview of the processes for Oxygen Generation, Complete Systems Architecture for a pilot lunar plant, experimental apparatus development and initial experimental results, and future directions.

Ramachandran, N.↗

NASA NTRS2006

The Pore Formation and Mobility Investigation: A Summary of Conducted Research on the International Space Station

The Pore Formation and Mobility Investigation (PFMI) is being conducted in the Microgravity Science Glovebox (MSG) aboard the International Space Station (ISS) with the goal of understanding bubble generation and interactions during controlled directional solidification processing. Through the course of the experiments, beginning in September 2002, a number of key factors pertinent to solidification processing of materials in a microgravity environment have been directly observed, measured, and modeled. Though most experiments ran uninterrupted, on four separate occasions malfunctions to the PFMI hardware and software were experienced that required crew intervention, including in-space repair. Fortunately, each repair attempt was successful and restored the PFMI apparatus to a fully functional condition. Based on PFMI results and lessons learned, the intent of this presentation is to draw attention to the role ISS experiments/hardware can play in providing insight to potential fabrication processing techniques and repair scenarios that might arise during long duration space transport and/or on the lunar/Mars surface.

Grugel, R. N.↗

NASA NTRS2006

On-Orbit Testing of Materials and Processes

The Pore Formation and Mobility Investigation (PFMI) and the In-Space Soldering Investigation (ISSI) were conducted aboard the International Space Station (ISS) with the intent of promoting our understanding of materials processing in a low-gravity environment. The numerous experiments were conducted by telescience with the results evaluated by real time video and subsequently returned tapes and samples. In addition to discussing the experimental results and analysis the presentation will include an account of the ISS facilities (Microgravity Science Glovebox and Maintenance Work Area) used as well as some lessons-learned comments.

Grugel, R. N.↗

NASA NTRS2005

Reproducible Crystal Growth Experiments in Microgravity Science Glovebox at the International Space Station (SUBSA Investigation)

Solidification Using a Baffle in Sealed Ampoules (SUBSA) is the first investigation conducted in the Microgravity Science Glovebox (MSG) Facility at the International Space Station (ISS) Alpha. 8 single crystals of InSb, doped with Te and Zn, were directionally solidified in microgravity. The experiments were conducted in a furnace with a transparent gradient section, and a video camera, sending images to the earth. The real time images (i) helped seeding, (ii) allowed a direct measurement of the solidification rate. The post-flight characterization of the crystals includes: computed x-ray tomography, Secondary Ion Mass Spectroscopy (SIMS), Hall measurements, Atomic Absorption (AA), and 4 point probe analysis. For the first time in microgravity, several crystals having nearly identical initial transients were grown. Reproducible initial transients were obtained with Te-doped InSb. Furthermore, the diffusion controlled end-transient was demonstrated experimentally (SUBSA 02). From the initial transients, the diffusivity of Te and Zn in InSb was determined.

Ostrogorsky, A.↗

NASA NTRS2005

The Pore Formation and Mobility Investigation: A Case Study for Conducting Research on the International Space Station in Support of Exploration

Grugel, R. N.↗

NASA NTRS2005

Bridgman Growth of Germanium Crystals in a Rotating Magnetic Field

A series of (100)-oriented gallium-doped germanium crystals has been grown by the vertical Bridgman method and under the influence of a rotating magnetic field (RMF). Time-dependent flow instabilities occur when the critical magnetic Taylor number (Tm(sup c)) is exceeded, and this can be observed by noting the appearance of striations in the grown crystals. Tm(sup c) decreases as the aspect ratio of the melt increases, and approaches the theoretical limit expected for an infinite cylinder. Intentional interface demarcations are introduced by pulsing the RMF on and off The RMF has a marked affect on the interface shape, changing it from concave to nearly flat as the RMF strength is increased.

Volz, M. P.↗

NASA NTRS2005

X-ray Characterization of Detached-Grown Germanium Crystals

Germanium (111)-oriented crystals have been grown by the vertical Bridgman technique, in both detached and attached configurations. Microstructural characterization of these crystals has been performed using synchrotron white beam x-ray topography (SWBXT) and double axis x-ray diffraction. Dislocation densities were measured from x-ray topographs obtained using the reflection geometry. For detached-grown crystals, the dislocation density is 4-6 x 10(exp 4) per square centimeter in the seed region, and decreases in the direction of growth to less than 10(exp 3) per square centimeter, and in some crystals reaches less than 10(exp 2) per square centimeter. For crystals grown in the attached configuration, dislocation densities were on the order of 10(exp 4) per square centimeter in the middle of the crystals, increasing to greater than 10(exp 5) per square centimeter near the edge. The measured dislocation densities are in excellent agreement with etch pit density results. The rocking curve linewidths were relatively insensitive to the dislocation densities. However, broadening and splitting of the rocking curves were observed in the vicinity of subgrain boundaries identified by x-ray topography in some of the attached-grown crystals.

Volz, M. P.↗

NASA NTRS2004

Bridgman Growth of Germanium Crystals in a Rotating Magnetic Field

A series of (100)-oriented gallium-doped germanium crystals have been grown by the Bridgman method and under the influence of a rotating magnetic field (RMF). Time-dependent flow instabilities occur when the critical magnetic Taylor number (Tm(sup c) is exceeded, and this can be observed by noting the appearance of striations in the grown crystals. The experimental data indicate that Tm(sup c) increases as the aspect ratio of the melt decreases. Modeling calculations predicting Tm(sup c) as a function of aspect ratio are in reasonable agreement with the experimental data. The RMF has a marked affect on the interface shape, changing it from concave to nearly flat as the RMF strength is increased. Also, by pulsing the RMF on and off, it is shown that intentional interface demarcations can be introduced.

Volz, M. P.↗

NASA NTRS2004

Detached Growth of Germanium by Directional Solidification

The conditions of detached solidification under controlled pressure differential across the meniscus were investigated. Uncoated and graphite- or BN-coated silica and pBN crucibles were used. Detached and partly detached growth was achieved in pBN and BN-coated crucibles, respectively. The results of the experiments are discussed based on the theory of Duffar et al.

Palosz, W.↗

NASA NTRS2003

An Experimental Investigation To Determine Interaction Between Rotating Bodies

A brass (copper+zinc) wheel, with a 4-in diameter and 1.4 in thick, was used for this investigation. Ceramic ball bearings were used to safely spin the wheel up to 40,000 rpm. The wheel was also electrically insulated from the rest of the armature. For spinning, an air turbine was used. The rotational velocity was measured by two methods: (1) A simple strobe light and (2) a photodiode that detected laser beam pulses as they passed through a slot in the rotating shaft. The magnetic sensor is based on a giant magnetoresistivity, and consists of a balanced bridge circuitry. The position of the sensor was as close as possible to the rim of the wheel. The linear dimension of the sensor is approximately equal to 8 mm so that the offset from the surface is on the order of 15 percent. We did not use any goniometer system, so the accuracy of the angular position is not high, being estimated within a few degrees, with the main uncertainty being the direction of Earth's magnetic field. We attempted to fit the experimental data with the presented theory by selecting the best value for the electrical conductivity of the wheel. The results of this procedure are displayed, where the black dots represent experimental values. A slight misfit on the right shoulder can be due to slight angular misalignment from a 90 degree position. The obtained value for the resistivity is 43 n(OMEGA)m, which compares well with those listed. We can conclude, based on these measurements, that the proposed theory satisfactorily explains our experiments.

Grugel, R. N.↗

NASA NTRS2003

Rayleigh-Benard Instability in a Vertical Cylinder with a Rotating Magnetic Field

This paper presents a linear stability analysis for the Rayleigh-Benard convection in a finite-length, vertical cylinder with a rotating magnetic field. The vertical wall of the cylinder is adiabatic, and planar top and bottom walls are isothermal with a higher temperature at the bottom. The stabilizing effects of the rotating magnetic field are studied for four values of the Prandtl number. Results for one Prandtl number are compared to previously published experimental results.

Walker, J. S.↗

NASA NTRS2003

Solidification Using the Baffle in Sealed Ampoules

Ostrogorsky, A.↗

NASA NTRS2003

In-Situ Pressure Measurements During the Detached Growth of Germanium

Crystal growth by the vertical Bridgman method in which there is little or no contact between the wall and the crystal has been termed detached solidification. Detachment has been observed frequently in previous microgravity experiments, and has been reported under some terrestrial conditions as well. It is expected that detachment can be conditioned by establishing an appropriate pressure difference below and above the melt. To test this hypothesis, an experimental technique has been developed to measure this pressure difference during the growth of germanium by the vertical Bridgman method. The apparatus allows for both monitoring the pressures and actively controlling them during growth. For a given melt height, there is a maximum pressure difference attainable before gas bubbles up through the melt. This maximum pressure increases with increasing melt height. As the melt height approaches zero, the maximum pressure difference, about 20 mbar in these experiments, is determined by the surface tension and gap width of the meniscus at the bottom of the melt.

Volz, M. P.↗

NASA NTRS2003

Lorentz Body Force Induced by Traveling Magnetic Fields

The Lorentz force induced by a traveling magnetic field (TMF) in a cylindrical container has been calculated. The force can be used to control flow in dectrically conducting melts and the direction of the magnetic field and resulting flow can be reversed. A TMF can be used to partially cancel flow driven by buoyancy. The penetration of the field into the cylinder decreases as the frequency increases, and there exists an optimal value of frequency for which the resulting force is a maximum. Expressions for the Lorentz force in the limiting cases of low frequency and infinite cylinder are also given and compared to the numerical calculations.

Volz, M. P.↗

NASA NTRS2002

Stability of Detached Grown Germanium Single Crystals

Detachment of the melt meniscus from the crucible during semiconductor Bridgman growth experiments has been observed in recent years especially, under microgravity experiments. Under earth conditions, the hydrostatic pressure counteracts the mechanism, whereby it is more difficult to achieve detached Bridgman growth. Attempts to get stable detached growth under terrestrial conditions have been discussed in the literature and have been the subject of recent experiments in our own group. The advantage of crystals grown without wall contact is obvious: In general, they possess a higher crystal quality than conventional Bridgman grown crystals with wall contact. However, due to the interaction of different parameters such as the wetting behavior of the melt with the crucible, and the dependence of the growth angle with the shape of the melt meniscus, the mechanism leading to detachment is very complicated and not completely understood. We have grown several doped and undoped Germanium crystals with the detached Bridgman and the normal Bridgman growth technique. Pyrolytic boron nitride containers were used for all growth experiments. In the detached grown crystals the typical gap thickness between the pBN crucible and the crystal is in the range of 10 to 100 microns, which was determined by performing profilometer measurements. Etch pit density measurements were also performed and a comparison between detached and attached grown crystals will be given. An interesting feature was detected on the surface of a detached grown crystal. Strong surface striations with an average axial distance of 0.5mm were observed around the whole circumference. The maximum fluctuation of the gap thickness is in the range of 5-10 microns. These variations of the detached gap along the crystal axis can be explained by a kind of stiction of the melt/crucible interface and thus by a variation of the meniscus shape. This phenomenon leading to the fluctuation of the gap thickness will be discussed in detail.

Schweizer, M.↗

NASA NTRS2002

Solutocapillary Convection in the Float-Zone Process with a Strong Magnetic Field

This paper treats the axisymmetric flow and mass transport in a cylindrical liquid bridge between the melting end of a feed rod and the solidifying end of an alloyed semiconductor crystal. There is a strong, uniform, steady, axial magnetic field. The surface tension depends on the temperature and the concentration of the species, while variations of the concentration occur because one species is rejected into the liquid during solidification. The thermocapillary and solutocapillary convections tend to cancel- over part of the liquid bridge. For certain parameter ranges, there are two different stable steady solutions: one where the concentration gradient along the free surface leads to dominance by the solutocapillary convection and one where the mass transport due to the thermocapillary convection makes the concentration gradient along the free surface small, so that the thermocapillary convection is dominant.

Walker, J. S.↗