Engineering topics

Von Glahn, U.

Publications and source records attributed to Von Glahn, U..

At least 19 records

NASA NTRS1986

Velocity and temperature decay characteristics of inverted-profile jets

In order to design efficient, lightweight flap systems for future engine under-the-wing STOL aircraft, the velocity and temperature decay rate of the jet plume must be increased relative to that for single-stream nozzles in order to provide local flap loads and structural temperatures within acceptable limits. The jet plume decay rate of dual flow engines can be increased by resorting to inverted-profile velocity and temperature nozzle concepts. The peak axial decay characteristics of model-scale, two-stream inverted-profile nozzle flows are empirically correlated. Also discussed are the radial and spreading characteristics of inverted-profile nozzle flows.

Von Glahn, U.↗

NASA NTRS1984

Velocity and temperature characteristics of two-stream, coplanar jet exhaust plumes

The subsonic jet exhaust velocity and temperature characteristics of model scale, two stream coplanar nozzles were obtained experimentally. The data obtained included the effects of fan to primary stream velocity and temperature ratios on the jet axial and radial flow characteristics. Empirical parameters were developed to correlate the measured data. The resultant equations were shown to be extensions of a previously published single stream jet velocity and temperature correlation.

Von Glahn, U.↗

NASA NTRS1981

Comparison of predicted engine core noise with proposed FAA helicopter noise certification requirements

Calculated engine core noise levels, based on NASA-Lewis prediction procedures, for five representative helicopter engines are compared with measured total helicopter noise levels and proposed FAA helicopter noise certification requirements. Comparisons are made for level flyover and approach procedures. The measured noise levels are generally significantly greater than those predicted for the core noise levels, except for the Sikorsky S-61 and S-64 helicopters. However, the predicted engine core noise levels are generally at or within 3 dB of the proposed FAA noise rules. Consequently, helicopter engine core noise can be a significant contributor to the overall helicopter noise signature and, at this time, will provide a limiting floor to a further decrease in future noise regulations.

Von Glahn, U.↗

NASA NTRS1980

New interpretations of shock-associated noise with and without screech

Anomalous trends in present convergent nozzle (Mach 1) shock-associated noise analyses and predictions, with particular emphasis on the roles of screech and jet temperature, are discussed. Experimentally measured values of shock-associated noise are used to reassess data trends, including both frequency and sound pressure level. The data used includes model-scale nozzles, varying in nominal diameter from 5 cm to 13 cm, and full-scale engine nozzles up to 48 cm. All data were obtained at static conditions. From this reassessment of the measured data, new empirical methods for the prediction of shock-associated noise are developed. Separate procedures are presented for screech-free and screech-contaminated shock-associated noise. In the present approach, shock-associated noise spectra are developed from considerations that include the peak sound pressure level and its frequency, the low frequency sound pressure level slope, and the high frequency sound pressure level slope or roll-off; the latter is shown to vary with directivity angle.

Von Glahn, U.↗

NASA NTRS1980

Noise suppression due to annulus shaping of a conventional coaxial nozzle

Previous studies have shown that increasing the annulus width of a conventional coaxial nozzle with constant bypass velocity will lower the noise level. In the present model-scale study, the annulus was shaped by an eccentric mounting of the annular nozzle with respect to the conical core nozzle. Acoustic measurements were made in the flyover plane below the widest portion of the annulus and at 90 deg and 180 deg from this point. The model-scale spectra are scaled up to engine size (1.07 m diameter) and the perceived noise levels for the eccentric and concentric coaxial nozzles are compared over a limited range of operating conditions. The implications of the acoustic benefits derived from the eccentric nozzle to practical applications are discussed.

Von Glahn, U.↗

NASA NTRS1980

Noise suppression due to annulus shaping of an inverted-velocity-profile coaxial nozzle

Previous studies have shown that an inverted-velocity-profile coaxial nozzle for use with supersonic cruise aircraft produces less jet noise than an equivalent conical nozzle. Furthermore, decreasing the annulus height (increasing radius ratio with constant flow) results in further noise reduction benefits. In the present model-scale study, the annulus shape, that is, height, was varied by an eccentric mounting of the annular nozzle with respect to a conical core nozzle. Acoustic measurements were made in the flyover plane below the narrowest portion of the annulus and at 90 deg and 180 deg from this point. The model-scale spectra are scaled up to engine size (1.07 m diameter) and the perceived noise levels for the eccentric and baseline concentric inverted-velocity-profile coaxial nozzles are compared over a range of operating conditions. The implications of the acoustic benefits derived with the eccentric nozzle to practical applications are discussed.

Goodykoontz, J.↗

NASA NTRS1980

Acoustic considerations of flight effects on jet noise suppressor nozzles

Insight into the inflight acoustic characteristics of high-velocity jet noise suppressor nozzles for supersonic cruise aircraft (SCA) is provided. Although the suppression of jet noise over the entire range of directivity angles is of interest, the suppression of the peak noise level in the rear quadrant is frequently of the most interest. Consequently, the paper is directed primarily to the inflight effects at the peak noise level. Both single and inverted-velocity-profile multistream suppressor nozzles are considered. The importance of static spectral shape on the noise reduction due to inflight effects is stressed.

Von Glahn, U.↗

NASA NTRS1979

Assessment at full scale of exhaust nozzle-to-wing size on STOL-OTW acoustic characteristics

On the basis of static zero/acoustic data obtained at model scale, the effect of exhaust nozzle size on flyover noise is evaluated at full scale for different STOL-OTW nozzle configurations. Three types of nozzles are evaluated: a circular/deflector nozzle mounted above the wing, a slot/deflector nozzle mounted on the wing, and a slot nozzle mounted on the wing. The nozzle exhaust plane location, measured from the wing leading edge was varied from 10 to 46 percent of the wing chord (flaps retracted). Flap angles of 20 deg (takeoff) and 60 deg (approach) are included in the study. Initially, perceived noise levels (PNL) are calculated as a function of flyover distance at 152 m altitude. From these plots static EPNL values, defined as flyover relative noise levels, then are obtained as functions of nozzle size for equal aerodynamic performance (lift and thrust). On the basis of these calculations, the acoustic benefits attributable to nozzle size relative to a given wing chord size are assessed.

Von Glahn, U.↗

NASA NTRS1979

Wing aerodynamic loading caused by jet-induced lift associated with STOL-OTW configurations

Surface pressure distributions were obtained with model-scale STOL-OTW configurations using various nozzles designed to promote flow attachment to the wing-flap surface. The nozzle configurations included slot-types and both circular and slot nozzles with external flow deflectors. The wing aerodynamic loading caused by the jet-induced lift is presented in conventional terms of delta p/q as a function of chordwise surface distance in the nozzle centerline plane as well as outboard of the nozzle centerline. Included in the geometric variables affecting the wing loading are nozzle roof/deflector angle, chordwise location of the nozzle, wing size, and flap deflection angle.

Von Glahn, U.↗

NASA NTRS1979

Assessment at full scale of nozzle/wing geometry effects on OTW aeroacoustic characteristics

The effects on acoustic characteristics of nozzle type and location on a wing for STOL engine over-the-wing configurations are assessed at full scale on the basis of model-scale data. Three types of nozzle configurations are evaluated: a circular nozzle with external deflector mounted above the wing, a slot nozzle with external deflector mounted on the wing and a slot nozzle mounted on the wing. Nozzle exhaust plane locations with respect to the wing leading edge are varied from 10 to 46 percent chord (flaps retracted) with flap angles of 20 deg (take-off attitude) and 60 deg (approach attitude). Perceived noise levels (PNL) are calculated as a function of flyover distance at 152 m altitude. From these plots, static EPNL values, defined as flyover relative noise levels, are calculated and plotted as a function of lift and thrust ratios. From such plots the acoustic benefits attributable to variations in nozzle/deflector/wing geometry at full scale are assessed for equal aerodynamic performance.

Groesbeck, D.↗

NASA NTRS1977

Noise of deflectors used for flow attachment with STOL-OTW configurations

Future STOL aircraft may utilize engine-over-the-wing (OTW) installations in which the exhaust nozzles are located above and separated from the upper surface of the wing. An external jet-flow deflector can be used with such installations to provide flow attachment to the wing/flap surfaces for lift augmentation. In the present work, the deflector noise in the flyover plane measured with several model-scale nozzle/deflector/wing configurations is examined. The deflector-associated noise is correlated in terms of velocity and geometry parameters. The data also indicate that the effective overall sound pressure level of the deflector-associated noise peaks in the forward quadrant near 40 deg from the inlet axis.

Von Glahn, U.↗

NASA NTRS1977

Interim noise correlation for some OTW configurations using external jet-flow deflectors

Jet/flap interaction acoustic data obtained statically from a model-scale study of STOL-OTW configurations with a conical nozzle mounted above the wing and using various external deflectors to provide jet-flow attachment are correlated. The acoustic data are correlated in terms that consider the jet/flap interaction noise contributions associated primarily with fluctuating lift, trailing edge, and configuration wake noise sources. Variables considered include deflector geometry, flap setting and wing size. Finally, the configuration overall noise levels are related to static lift and thrust measurements in order to provide insight into possible acoustic/aerodynamic performance trade-off benefits.

Von Glahn, U.↗

NASA NTRS1976

OTW noise correlation for several nozzle/wing geometries using a 5:1 slot nozzle with external deflectors

Acoustic spectral data obtained from a model-scale study of several OTW configurations with a 5:1 slot nozzle using various external deflectors are correlated in terms of deflector geometry and flow parameters. Variations in the deflector geometry include deflector size and deflector angle. In addition, geometry variations in flap setting and nozzle chordwise location are included. Three dominant noise sources are correlated: fluctuating lift noise, flap trailing edge noise, and jet mixing noise. Aerodynamic characteristics, including lift and thrust measurements, obtained for the various configurations are summarized.

Von Glahn, U.↗

NASA NTRS1976

OTW noise correlation for variations in nozzle/wing geometry with 5:1 slot nozzles

Acoustic data obtained from a model-scale study with 5:1 slot nozzles are analyzed and correlated in terms of apparent noise sources. Variations in nozzle geometry include roof angle and sidewall cutback. In addition, geometry variations in wing size and flap deflection were included. Three dominant noise sources were evident in the data and correlated: fluctuating lift noise, trailing edge noise and a redirected jet mixing noise that included the effect of reflection of jet noise by the surface. Pertinent variables in the correlations included the shear layer thickness and peak jet flow velocity at the trailing edge.

Von Glahn, U.↗

NASA NTRS1976

Wing shielding of high-velocity jet and shock-associated noise with cold and hot flow jets

Jet exhaust noise shielding data are presented for cold and hot flows (ambient to 1100 K) and pressure ratios from 1.7 to 2.75. A nominal 9.5-cm diameter conical nozzle was used with simple shielding surfaces that were varied in length from 28.8 to 114.3 cm. The nozzle was located 8.8 cm above the surfaces. The acoustic data with the various shielding lengths are compared to each other and to that for the nozzle alone. In general, short shielding surfaces that provided shielding for subsonic jets did not provide as much shielding for jets with shock noise; however, long shielding surfaces did shield shock noise effectively.

Von Glahn, U.↗

NASA NTRS1976

Nozzle and wing geometry effects on OTW aerodynamic characteristics

The effects of nozzle geometry and wing size on the aerodynamic performance of several 5:1 aspect ratio slot nozzles are presented for OTW configurations. Nozzle geometry variables include roof angle, sidewall cutback, and nozzle chordwise location. Wing variables include chord size, and flap deflection. Several external deflectors also were included for comparison. The data indicate that good flow turning may not necessarily provide the best aerodynamic performance. The results of the study suggest that a variable exhaust nozzle geometry offers the best solution for a viable OTW configuration.

Von Glahn, U.↗

NASA NTRS1976

Effect of external jet-flow deflector geometry on OTW aero-acoustic characteristics

The effect of geometry variations in the design of external deflectors for use with OTW configurations was studied at model scale and subsonic jet velocities. Included in the variations were deflector size and angle as well as wing size and flap setting. A conical nozzle (5.2-cm diameter) mounted at 0.1 chord above and downstream of the wing leading edges was used. The data indicate that external deflectors provide satisfactory take-off and approach aerodynamic performance and acoustic characteristics for OTW configurations. These characteristics together with expected good cruise aerodynamics, since external deflectors are storable, may provide optimum OTW design configurations.

Von Glahn, U.↗

NASA NTRS1975

Installation and airspeed effects on jet shock-associated noise

Experimental acoustic data are presented to illustrate, at model scale, the effect of varying the nozzle-wing installation on shock-associated noise, statically and with airspeed. The variation in installations included nozzle only, nozzle under-the-wing, and nozzle over-the-wing. With the nozzle only, shock wave noise dominated the spectra in the forward quadrant, while jet mixing noise dominated in the rearward quadrant. Similar trends were observed when a wing (flaps retracted) was included. Shock noise was attenuated with an over-the-wing configuration and increased with an under-the-wing configuration (due to reflection from the wing surface). With increasing flap deflection (under-the-wing configuration), the jet-flap interaction noise exceeded the shock noise and became dominant in both quadrants. The free jet results showed that airspeed had no effect on shock noise.

Von Glahn, U.↗