Engineering topics

Von Jamora

Publications and source records attributed to Von Jamora.

3 records

NASA NTRSDate not supplied

RESIDUAL DEFORMATION ANALYSIS IN COMPOSITE SHELL STRUCTURES MANUFACTURED USING AUTOMATED FIBER PLACEMENT

The manufacturing of composites typically produces residual stresses that can significantly affect the final shape of the structure. The process of automated fiber placement (AFP) has become a prominent manufacturing technique in developing layups with tailored, variable stiffness morphology. The steered patterns of fiber tows with and without overlaps produce residual deformations that are distinctive from traditional layups. Digital image correlation was used to measure the AFP lamina coefficients of thermal expansion, which were incorporated into finite element analyses (FEA) to model the cooling phase of the cure cycle. The effects of nonlinear analysis and temperature-dependent lamina properties calculated using self-consistent field micromechanics, on the resulting residual deformation of shells, were also modeled. The predicted residual deformation was analyzed by considering out-of-roundness in cylindrical shells and compared to the experimental results. The shell FEA results were well-correlated with the overall deformed shape of the AFP cylinder with overlaps, while the shell FEA model of the AFP cylinder without overlaps did not show as good of qualitative match of the deformation pattern. Analytical correlation with measured results were insensitive to material softening at elevated temperatures, geometric nonlinearities, and variations in measured lamina thermal properties. To improve the accuracy of the residual deformation analysis, these results suggest that the thermo-chemical shrinkages preceding the cooldown should be considered, as well as possible variations in ply level microstructure due to the presence of the embedded fiber tow gaps and overlaps.

Composites↗

NASA NTRSDate not supplied

Integration of Structural Analysis and Manufacturing Process Planning for Global Optimization with Automated Fiber Placement

Design of mass-efficient composite structures intended for Automated Fiber Placement (AFP) requires close interaction between structural analysis and manufacturing process planning. Tools exist for each of these disciplines, but software interplay has been insufficient for rapid and efficient design iteration. Within the NASA Advanced Composites Consortium (ACC), the Design for Manufacturing (DFM) task has made significant progress towards linking these disciplines and respective software – HyperX (design), CAPP (process planning), and VCP (tool path generation). The initial focus in previous work was on data exchange between disciplines. The ability to both export and consume composite design and manufacturing data to and from each tool. This paper focuses on the effort to automate and streamline the connection between the tools listed above, with the goal of being able to automatically generate a composite AFP design that is mass-efficient and manufacturable. The optimization method being pursued is a bi-level approach, where each tool performs optimization within its discipline. The optimization in HyperX is focused on mass and laminate strength, while CAPP is focused on maximizing manufacturability. VCP is used to generate fiber paths for each design iteration. These sub-processes are wrapped with a global level optimization, driven by HyperX, used to converge the design. This paper describes the current state of this effort, which is a completed HyperX-VCP iteration loop and initial work on the HyperX-CAPP iteration loop. Additionally, example results are shown for a wind blade structure with double curvature.

Automated Fiber Placement↗

NASA NTRSDate not supplied

Design for Manufacturing of Structures with Automated Fiber Placement via Integration of Analysis and Process Planning

Under the Design for Manufacturing (DFM) task in the NASA HiCAM program, significant process has been made towards establishing a fully automated optimization process that spans the structural analysis, design, and manufacturing process planning for Automated Fiber Placement (AFP) structures. Previous efforts in this area established the data formats and mapping processes needed to exchange data between disciplines. The software tools used in the framework are HyperX (structural optimization), CAPP (process planning), and VCP (AFP path generation). The work has culminated with automation of data exchanges and an optimization process that drives the three software toward convergence. Within this framework, HyperX is used to generate mass-optimum composite designs which are iterated with VCP and CAPP to improve manufacturability of the designs. As the ply manufacturing process is adjusted by CAPP and VCP, HyperX continually re-assesses the structural integrity of the part and makes adjustments to the laminate as needed. For example, the position of fiber steering and tow overlaps/gaps can necessitate changes to the laminate design. Once the design converges, the end result is a stack of plies that meets both structural and manufacturing requirements. This paper presents the details of the framework and demonstrations the automated process on several parts with significant double-curvature.

HiCAM↗