Engineering topics
Publications and source records attributed to Vook, Trevor.
The overwhelming demand for lithium-ion batteries necessitates a sustainable and environment-friendly production of graphite anode materials. Catalytic graphitization of pyrolysis oil is promising for mass-scale production of biographite.
We report a novel method for the conversion of paper towel waste to biographite anode material is developed and optimized for use in Li-ion batteries. The surge in demand for Li-ion battery anode materials coupled with the unsustainable and inefficient methods of producing battery-grade graphite necessitate alternative carbon feedstocks and graphitization technologies. Paper waste (PW) is identified as a suitable carbon feedstock for iron-catalyzed graphitization due to its sustainability, low cost, low ash content, and ample supply for the intended end use. A Box Behnken experimental design for statistical optimization is pursued for untreated and pre-carbonized PW with factors of temperature (1100-1300 °C), hold time (1-5 h), and iron catalyst loading (0.5-1.5x fixed carbon content) with biographite crystal size as the primary response variable. Temperature and iron catalyst loading are found to be significant factors, whereas hold time is found to be insignificant. Reversible capacities of the biographite anodes are found to be 340-355 mAh g-1 with 99% capacity retention over 100 cycles, indicating good electrochemical performance relative to commercial graphite anodes. The initial Coulombic efficiency of untreated and pre-carbonized biographites, however, are 77% and 75%, respectively, suggesting parasitic reactions including electrolyte decomposition.
Abstract The demand for electrochemical energy storage is increasing rapidly due to a combination of decreasing costs in renewable electricity, governmental policies promoting electrification, and a desire by the public to decrease CO 2 emissions. Lithium‐ion batteries are the leading form of electrochemical energy storage for electric vehicles and the electrical grid. Lithium‐ion cell anodes are mostly made of graphite, which is derived from geographically constrained, non‐renewable resources using energy‐intensive and highly polluting processes. Thus, there is a desire to innovate technologies that utilize abundant, affordable, and renewable carbonaceous materials for the sustainable production of graphite anodes under relatively mild process conditions. This review highlights novel attempts to realize the aforementioned benefits through innovative technologies that convert biocarbon resources, including lignocellulose, into high quality graphite for use in lithium‐ion anodes.
Here, a new method for producing green needle coke (GNC) is developed by replacing the “heavy fraction” of petroleum pitch delayed coking with fast pyrolysis biocrude. A series of alternative biocrude distillation, carbonization, and calcination conditions were investigated to determine the influence of these processing parameters onto the crystalline structure of the resulting graphitized material. For the first time, the addition of biochar fines was found to serve as a “physical template” to increase the graphitic nature of the final product. During the initial biocrude carbonization (350–450 °C), volatile compounds are released, and aromatics in pyrolysis biocrude experience condensation, resulting in GNC solids with carbon contents above 95 wt % and some early lamellar structure. In the second stage of the thermal process (25–1500 °C), there are additional thermal decomposition reactions with an increase in the aromatic nature of the graphitized solid. It was found that systematic addition of biochar fines induces a nucleating effect during the GNC development. Thermogravimetric analysis suggests that biochar fines promote polycondensation reactions by modifying the biopitch structure and molecular weight, while elemental analysis (CHN) shows a reduction in both H/C and O/C ratios which are consistent with the increase in aromaticity and removal of oxygenated compounds as thermal treatment evolves. The effects of different bio-based pitch materials (after distillation) and GNC intermediates were evaluated by pyrolysis-gas chromatography mass spectrometry and Fourier transform infrared, displaying slight changes on product yields and quality. X-ray diffraction patterns taken after graphitization evidence an increase in the graphitic order with the addition of biochar fines. Transmittance electron microscopy depicts an improvement on graphitic morphology as biochar fine content increases. The use of biochar fines showed a significant increase in graphitic ordering at addition levels above 0.01 wt %. These results show that thermally treated biocrude/biochar fine systems can produce graphitic structures (hard carbon-like) that might be suitable for the manufacture of sodium-ion batteries.
Lithium-ion batteries (LIB) are an important component of electric vehicles and sodium-ion batteries (SIB) are an attractive alternative for grid electric storage. We are investigating a novel approach to synthesizing the carbon anode materials for these batteries from biomass pyrolysis oil as part of conversion processes to produce biofuels. Graphite is used as anode material in LIB and is exclusively produced from petroleum residue or mined mineral carbon. We have synthesized drop-in graphite by coking the heavy residual oil from the distillation of catalytic fast pyrolysis oil and by catalytic graphitizing raw pyrolysis oil. XRD and Raman spectroscopies were used to verify the production of high purity crystalline graphite. Figure 1 shows typical XRD spectra of the bio-graphite compared to commercial material as well as the charge/discharge cycle. Graphite particle sizes and morphologies were adjusted to improve performance using jet milling and carbon coating. The bio-graphite delivered a high capacity (335 mAh/g) when tested in a graphite half-cell. Full cell coin cell experiments were also conducted to verify the observations from half-cell testing. The high value of graphite (>$9/kg) can positively impact the economics of biofuels production and can be an important part of a future circular carbon economy. We have also investigated synthesizing hard carbon from pyrolysis oil for use as anode material in SIB. These batteries are not commercially mature but have great promise in grid storage and use earth abundant elements. We have demonstrated that pyrolysis oil can be used to synthesize hard carbon, which was subsequently be used in SIB experiments. This material achieved a sodium-ion capacity of 250 mAh/g and a first cycle efficiency of 78%, with opportunities to further optimize this performance from optimizing the composition of the pyrolysis oil to shaping the hard carbon particles. As with graphite, hard carbon is a high value (> $10/kg) material that could facilitate biofuels production.