Search NASA⌕ Search

Engineering topics

Voronov, D. L.

Publications and source records attributed to Voronov, D. L..

Low blaze angle grating for fully dispersive x-ray spectroscopy

We demonstrate fabrication of an ultra-low blaze angle (LBA) grating designed for time-resolved spectroscopy in the x-ray region. A blaze angle of 0.12° was achieved by the groove depth reduction process providing a perfect saw-tooth shape of the grooves. The 200 lines/mm LBA grating exhibited high diffraction efficiency at a photon energy of 8 KeV. Use in a spectrometer would open up dispersive x-ray absorption spectroscopy across a wide energy range including the K edges of 3d transition metals, with much greater efficiency than traditional crystal spectrometers.

Voronov, D. L.↗

Nanometer flat blazed x-ray gratings using ion beam figure correction

With the development of nanometer accuracy stitching interferometry, ion beam figuring (IBF) of x-ray mirrors can now be achieved with unprecedented performance. However, the process of producing x-ray diffraction gratings on these surfaces may degrade the figure quality due to process errors introduced during the ruling of the grating grooves. To address this challenge, we have investigated the post-production correction of gratings using IBF, where stitching interferometry is used to provide in-process feedback. A concern with ion beam correction in this case is that ions will induce enough surface mobility of atoms to cause smoothing of the grating structure and degradation of diffraction efficiency. In this study we found however that it is possible to achieve a nanometer-level planarity of the global grating surface with IBF, while preserving the grating structure. The preservation was so good, that we could not detect a change in the diffraction efficiency after ion beam correction. This is of major importance in achieving ultra-high spectral resolution, and the preservation of brightness for coherent x-ray beams.

36 MATERIALS SCIENCE↗

6000 lines/mm blazed grating for a high-resolution x-ray spectrometer

We have designed and fabricated a high groove density blazed grating for a Resonant Inelastic X-ray Scattering spectrometer for the new Qerlin beamline at the Advanced Light Source (ALS) synchrotron facility. The gratings were fabricated using a set of nanofabrication techniques including e-beam lithography, nanoimprint, plasma etch, and anisotropic wet etching. Two gratings with groove density of 6000 lines/mm and 3000 lines/mm and optimized for operation in the 1st and 2nd negative diffraction order respectively were fabricated and tested. We report on fabrication details and characterization of the gratings at beamline 6.3.2 of the ALS.

36 MATERIALS SCIENCE↗

Highly efficient ultra-low blaze angle multilayer grating

We have developed an advanced process for blaze angle reduction of x-ray gratings for the soft, tender, and EUV spectral ranges. The process is based on planarization of an anisotropically etched Si blazed grating followed by a chemically selective plasma etch. This provides a way to adjust the blaze angle to any lower value with high accuracy. Here we demonstrate the reduction of the blaze angle to an extremely low value of 0.04°±0.004°. For a 100 lines/mm grating with a Mo/Si multilayer coating, the grating exhibits diffraction efficiency of 58% in the 1 st diffraction order at a wavelength of 13.3 nm. This technique will be applicable to a wide range of uses of high efficiency gratings for synchrotron sources, as well as for Free Electron Lasers (FEL).

42 ENGINEERING↗

Spontaneous formation of highly periodic nano-ripples in inclined deposition of Mo/Si multilayers

We investigated the growth of Mo/Si multilayers (ML) deposited using a highly collimated flux of ion-beam sputtered particles for a wide range of deposition angles. Growth of the multilayers at normal and moderately inclined deposition is dominated by surface relaxation resulting in smooth interfaces of the multilayer stack. The first signs of interface roughening are observed at a deposition angle of 45° with respect to the normal to the substrate surface. At an oblique angle of 55°, the ML interfaces undergo fast progressive roughening from the substrate to the top of the ML stack, leading to the formation of ripples which are perpendicular to the deposition flux direction. Deposition of the multilayer at an angle of 65° results in a highly periodic lateral ripple structure with a period of 10 nm. The mature ripple pattern forms during growth of only the first few layers and then stabilizes. The ripples propagate through the whole ML stack with almost no changes in frequency and amplitude, resulting in a highly periodic bulk array composed of silicon and molybdenum nano-rods closely packed in a 6-fold symmetric lattice. Here, we present a simple model for the ripple growth, which gives results that are in good agreement with experimental data.

36 MATERIALS SCIENCE↗

Innovative diffraction gratings for high-resolution resonant inelastic soft x-ray scattering spectroscopy

High-resolution Resonant Inelastic X-ray Scattering (RIXS) requires diffraction gratings with very exacting characteristics. The gratings should provide both very high dispersion and high efficiency which are conflicting requirements and extremely challenging to satisfy in the soft x-ray region for a traditional grazing incidence geometry. To achieve high dispersion one should increase the groove density of a grating; this however results in a diffraction angle beyond the critical angle range and results in drastic efficiency loss. The problem can be solved by use of multilayer coated blazed gratings (MBG). In this work we have investigated the diffraction characteristics of MBGs via numerical simulations and have developed a procedure for optimization of grating design for a multiplexed high resolution imaging spectrometer for RIXS spectroscopy to be built in sector 6 at the Advanced Light Source (ALS). We found that highest diffraction efficiency can be achieved for gratings optimized for 4{sup th} or 5{sup th} order operation. Fabrication of such gratings is an extremely challenging technological problem. We present a first experimental prototype of these gratings and report its performance. High order and high line density gratings have the potential to be a revolutionary new optical element that should have great impact in the area of soft x-ray RIXS.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fabrication and characterization of Sb/B4C multilayer mirrors for soft X-rays

Structure characterization of Sb/B 4 C multilayers for soft X-ray optics with a layers thickness from 0.5 nm to 7 nm is reported for the first time. Sb/B 4 C coatings were manufactured via magnetron sputtering. Amorphous and crystalline phases of the layers and the multilayer structure parameters were characterized with the X-ray diffraction data and the TEM data. The Sb/B 4 C multilayers demonstrated long term stability of their parameters and performances. The reached value of the reflectance of the Sb/B 4 C multilayers is 19–28% measured at the near-normal incidence in the wavelength range of 6.64–8.5 nm. The influence of reduced Sb density on the reflectivity is discussed.

36 MATERIALS SCIENCE↗

Conformal growth of Mo/Si multilayers on grating substrates using collimated ion beam sputtering

Deposition of multilayers on saw-tooth substrates is a key step in the fabrication of multilayer blazed gratings (MBG) for extreme ultraviolet and soft x-rays. Growth of the multilayers can be perturbed by shadowing effects caused by the highly corrugated surface of the substrates, which results in distortion of the multilayer stack structure and degradation of performance of MBGs. In this study, to minimize the shadowing effects, we used an ion-beamsputtering machine with a highly collimated atomic flux to deposit Mo/Si multilayers on saw-tooth substrates. The sputtering conditions were optimized by finding a balance between smoothening and roughening processes in order to minimize degradation of the groove profile in the course of deposition and at the same time to keep the interfaces of a multilayer stack smooth enough for high efficiency. An optimal value of energy of 200 eV for sputtering Kr + ions was found by deposition of test multilayers on flat substrates at a range of ion energies. Two saw-tooth substrates were deposited at energies of 200 eV and 700 eV for the sputtering ions. It was found that reduction of the ion energy improved the blazing performance of the MBG and resulted in a 40% gain in the diffraction efficiency due to better replication of the groove profile by the multilayer. As a result of the optimization performed, an absolute diffraction efficiency of 28.8% was achieved for the 2nd blaze order of the MBG with a groove density of 7350 lines/mm at a wavelength of 13.5 nm. Lastly, details of the growth behavior of the multilayers on flat and saw-tooth substrates are discussed in terms of the linear continuous model of film growth.

36 MATERIALS SCIENCE↗

Ultra-high efficiency multilayer blazed gratings through deposition kinetic control

Diffraction efficiency of multilayer coated blazed gratings (MBG) strongly depends on the perfection of the saw-tooth-shaped layers in the overall composite structure. Growth of multilayers on saw-tooth substrates should be carefully optimized in order to reduce groove profile distortion and at the same time to avoid significant roughening of multilayer interfaces. In this work we report on a new way to optimize growth of sputter-deposited Mo/Si multilayers on saw-tooth substrates through variation of the sputtering gas pressure. Lastly, a new record for diffraction efficiency of 44% was achieved for a optimized MBG with groove density of 5250 lines /mm at the wavelength of 13.1 nm.

36 MATERIALS SCIENCE↗