Search NASA⌕ Search

Engineering topics

Voth, R. O.

Publications and source records attributed to Voth, R. O..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Liquid-vapour surface sensors for liquid nitrogen and hydrogen

The present paper identifies devices to serve as liquid-vapor detectors in zero gravity. The testing in LH2 was done in a sealed glass Dewar system to eliminate any chance of mixing H2 and air. Most of the tests were performed with the leads to the sensor horizontal. Some results of rapid cycle testing of LVDG in LH2 are presented. Findings of rapid-cycle testing of LVDG in LH2 are discussed. The sensor crossed the liquid surface when the position sensor registered 1.9 V, which occurred at about 0.4075 s. The delay time was about 1.5 ms. From the estimated slope of the position sensor curve at 1.9 V, the velocity of the sensor through the liquid surface is over 3 m/s. Results of tests of optical sensors are presented as well.

Siegwarth, J. D.↗
NASA NTRS1990

Hydrogen slush production with a large auger

The design and construction of a 178-mm-diameter auger-type hydrogen slush generator are described. A supercritical helium flow loop, which simulates the performance of a helium refrigerator, cools the generator. The coolant temperature varies down to 5 K and the flow varies about the 1.4 L/s (3 cfm) design point. The computer model of the auger-type generator shows that coolant temperature and auger speed have the greatest influence on slush production rate, although coolant flow rate and auger radial clearance are also important.

Daney, D. E.↗
NASA NTRS1974

Study of cryogenic propellant systems for loading the space shuttle

Computer programs were written to model the liquid oxygen loading system for the space shuttle. The programs allow selection of input data through graphic displays which schematically depict the part of the system being modeled. The computed output is also displayed in the form of graphs and printed messages. Any one of six computation options may be selected. The first four of these pertain to thermal stresses, pressure surges, cooldown times, flow rates and pressures during cooldown. Options five and six deal with possible water hammer effects due to closing of valves, steady flow and transient response to changes in operating conditions after cooldown. Procedures are given for operation of the graphic display unit and minicomputer.

Voth, R. O.↗
NASA NTRS1972

Cavitation data for hydraulic equipment

Development of cavitation B-factors for helium, parahydrogen, nitrogen, fluorine, oxygen, refrigerant 114, and water is discussed. B-factor is defined and numerical relationships are established. Mathematical models are included and alternative methods of determining B-factor are explained.

Hord, J.↗
NASA NTRS1972

A computer program for the calculation of thermal stratification and self-pressurization in a liquid hydrogen tank

An analysis and computer program are described for calculating the thermal stratification and the associated self-pressurization of a closed liquid hydrogen tank. FORTRAN-IV language is used and runs were made on IBM 360/65 and CDC 3600 computers. Comparisons are made between the program calculations and test results from both ground and orbital coast tests of a Centaur space vehicle.

Arnett, R. W.↗
NASA NTRS1972

Safety of hydrogen pressure gauges.

Study of the relative safety afforded an operator by various hydrogen-pressure gauge case designs. It is shown that assurance of personnel safety, should a failure occur, requires careful selection of available gauge designs, together with proper mounting. Specific gauge case features and mounting requirements are recommended.

Voth, R. O.↗
NASA NTRS1971

A study of LC-39 cryogenic systems. Part 1: A study of the vacuum insulated transfer lines at Kennedy Space Center. Part 2: Cooldown pressure surges

The vacuum liquid hydrogen and liquid oxygen transfer lines at Kennedy Space Center were studied to evaluate the feasibility of using a condensing gas such as CO2 inside the vacuum spaces to achieve a condensing-vacuum. The study indicates that at ambient temperature, a maximum vacuum hyphen space pressure of 4000 microns is acceptable for the LH2 transfer lines. In addition, the cooldown procedures for the 14-inch cross-country liquid oxygen line was studied using a simplified mathematical model. Preliminary cooldown times are presented for various heat leak rates to the line and for two vent configurations.

Ludtke, P. R.↗