Search NASA⌕ Search

Engineering topics

Voznyy, Oleksandr

Publications and source records attributed to Voznyy, Oleksandr.

Fast Near-Infrared Photodetection Using III–V Colloidal Quantum Dots

Colloidal quantum dots (CQDs) are promising materials for infrared (IR) light detection due to their tunable bandgap and their solution processing; however, to date, the time response of CQD IR photodiodes is inferior to that provided by Si and InGaAs. It is reasoned that the high permittivity of II–VI CQDs leads to slow charge extraction due to screening and capacitance, whereas III–Vs—if their surface chemistry can be mastered—offer a low permittivity and thus increase potential for high-speed operation. In initial studies, it is found that the covalent character in indium arsenide (InAs) leads to imbalanced charge transport, the result of unpassivated surfaces, and uncontrolled heavy doping. Surface management using amphoteric ligand coordination is reported, and it is found that the approach addresses simultaneously the In and As surface dangling bonds. The new InAs CQD solids combine high mobility (0.04 cm 2 V -1 s -1 ) with a 4× reduction in permittivity compared to PbS CQDs. Finally, the resulting photodiodes achieve a response time faster than 2 ns—the fastest photodiode among previously reported CQD photodiodes—combined with an external quantum efficiency (EQE) of 30% at 940 nm.

36 MATERIALS SCIENCE↗

Electro-Optic Modulation Using Metal-Free Perovskites

Electro-optic (EO) modulation is of interest to impart information onto an optical carrier. Inorganic crystals—most notably LiNbO 3 and BaTiO 3 —exhibit EO modulation and good stability, but are difficult to integrate with silicon photonic technology. Solution-processed organic EO materials are readily integrated but suffer from thermal degradation at the temperatures required in operating conditions for accelerated reliability studies. Hybrid organic–inorganic metal halide perovskites have the potential to overcome these limitations; however, these have so far relied on heavy metals such as lead and cadmium. Here, we report linear EO modulation using metal-free perovskites, which maintain the crystalline features of the inorganic EO materials and incorporate the flexible functionality of organic EO chromophores. We find that, by introducing a deficiency of cations, we reduce the symmetry in the perovskite crystal and produce thereby an increased EO response. The best-engineered perovskites reported herein showcase an EO coefficient of 14 pm V –1 at a modulation frequency of 80 kHz, an order of magnitude higher than in the nondefective materials. Furthermore, we observe split peaks in the X-ray diffraction and neutron diffraction patterns of the defective sample, indicating that the crystalline structure has been distorted and the symmetry reduced. Density functional theory (DFT) studies link this decreased symmetry to NH 4 + deficiencies. This demonstration of EO from metal-free perovskites highlights their potential in next-generation optical information transmission.

36 MATERIALS SCIENCE↗

Engineering Directionality in Quantum Dot Shell Lasing Using Plasmonic Lattices

In this paper, we report how the direction of quantum dot (QD) lasing can be engineered by exploiting high-symmetry points in plasmonic nanoparticle (NP) lattices. The nanolaser architecture consists of CdSe-CdS core-shell QD layers conformally coated on two-dimensional square arrays of Ag NPs. Using waveguide-surface lattice resonances (W-SLRs) near the Δ point in the Brillouin zone as optical feedback, we achieved lasing from the gain in CdS shells at off-normal emission angles. Changing the periodicity of the plasmonic lattices enables other high-symmetry points (Γ or M) of the lattice to overlap with the QD shell emission, which facilitates tuning of the lasing direction. We also increased the thickness of the QD layer to introduce higher order W-SLR modes with additional avoided crossings in the band structure, which expands the selection of cavity modes for any desired lasing emission angle.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Narrow Emission from Rb 3 Sb 2 I 9 Nanoparticles

Abstract Metal halide perovskites have gained attention for their optoelectronic properties and are employed as the active layer in solar cells, light‐emitting diodes, and photodetectors. However, the use of lead in the best‐performing perovskite devices may limit their wider application. Prior reports of lead‐free perovskite nanoparticles have exhibited linewidths more than twice as wide as their lead‐halide counterparts, limiting their attainable color gamut. Here the solution synthesis of lead‐free Rb 3 Sb 2 I 9 nanoplatelets and single crystals is reported; the single crystals exhibit broad (full‐width at half‐maximum (FWHM) = 75 nm) photoluminescence centered at 635 nm, while the nanoplatelets exhibit narrow emission (FWHM = 21 nm) at 512 nm. The photoluminescence quantum yield of both the single crystals and nanoplatelets is low and the present demonstration of the narrowest emission among all lead‐free perovskites reported to date motivates further study of how these and related materials can achieve further‐enhanced brightness.

Johnston, Andrew↗

In Situ Back‐Contact Passivation Improves Photovoltage and Fill Factor in Perovskite Solar Cells

Abstract Organic–inorganic hybrid perovskite solar cells (PSCs) have seen a rapid rise in power conversion efficiencies in recent years; however, they still suffer from interfacial recombination and charge extraction losses at interfaces between the perovskite absorber and the charge–transport layers. Here, in situ back‐contact passivation (BCP) that reduces interfacial and extraction losses between the perovskite absorber and the hole transport layer (HTL) is reported. A thin layer of nondoped semiconducting polymer at the perovskite/HTL interface is introduced and it is shown that the use of the semiconductor polymer permits—in contrast with previously studied insulator‐based passivants—the use of a relatively thick passivating layer. It is shown that a flat‐band alignment between the perovskite and polymer passivation layers achieves a high photovoltage and fill factor: the resultant BCP enables a photovoltage of 1.15 V and a fill factor of 83% in 1.53 eV bandgap PSCs, leading to an efficiency of 21.6% in planar solar cells.

Tan, Furui↗

Spectrally Resolved Ultrafast Exciton Transfer in Mixed Perovskite Quantum Wells

Solution-processed perovskite quantum wells have been utilized to fabricate increasingly efficient and stable optoelectronic devices. Little is known about the dynamics of photogenerated excitons in perovskite quantum wells within the first few hundred femtoseconds-a crucial time scale on which energy and charge transfer processes may compete. In this work we use ultrafast transient absorption and two-dimensional electronic spectroscopy to clarify the movement of excitons and charges in reduced-dimensional perovskite solids. We report excitonic funneling from strongly to weakly confined perovskite quantum wells within 150 fs, facilitated by strong spectral overlap and orientational alignment among neighboring wells. This energy transfer happens on time scales orders of magnitude faster than charge transfer, which we find to occur instead over 10s to 100s of picoseconds. Simulations of both Forster-type interwell exciton transfer and free carrier charge transfer are in agreement with these experimental results, with theoretical exciton transfer calculated to occur in 100s of femtoseconds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dipolar cations confer defect tolerance in wide-bandgap metal halide perovskites

Efficient wide-bandgap perovskite solar cells (PSCs) enable high-efficiency tandem photovoltaics when combined with crystalline silicon and other low-bandgap absorbers. However, wide-bandgap PSCs today exhibit performance far inferior to that of sub-1.6-eV bandgap PSCs due to their tendency to form a high density of deep traps. Here, we show that healing the deep traps in wide-bandgap perovskites—in effect, increasing the defect tolerance via cation engineering—enables further performance improvements in PSCs. We achieve a stabilized power conversion efficiency of 20.7% for 1.65-eV bandgap PSCs by incorporating dipolar cations, with a high open-circuit voltage of 1.22 V and a fill factor exceeding 80%. We also obtain a stabilized efficiency of 19.1% for 1.74-eV bandgap PSCs with a high open-circuit voltage of 1.25 V. From density functional theory calculations, we find that the presence and reorientation of the dipolar cation in mixed cation–halide perovskites heals the defects that introduce deep trap states.

36 MATERIALS SCIENCE↗

Theory-driven design of high-valence metal sites for water oxidation confirmed using in situ soft X-ray absorption

The efficiency with which renewable fuels and feedstocks are synthesized from electrical sources is limited at present by the sluggish oxygen evolution reaction (OER) in pH-neutral media. Here, we took the view that generating transition metal sites with high valence at low applied bias should improve the activity of neutral OER catalysts. Using density functional theory, we find that the formation energy of desired Ni 4+ sites is systematically modulated by incorporating judicious combinations of Co, Fe and non-metal phosphorus. Here we synthesized NiCoFeP oxyhydroxides and probed their oxidation kinetics by employing in situ soft X-ray absorption (sXAS). In situ sXAS studies of neutral-pH OER catalysts indicate ready promotion of Ni 4+ under low overpotential conditions. NiCoFeP catalyst outperforms IrO 2 and retains its performance following 100 hours of operation. We showcase NiCoFeP in a membrane-free CO 2 electroreduction system that achieves a 1.99 V cell voltage at 10 mA cm -2 , reducing CO 2 into CO and oxidizing H 2 O to O 2 with a 64% electricity-to-chemical-fuel efficiency.

30 DIRECT ENERGY CONVERSION↗

Perovskite-Fullerene Hybrid Materials Eliminate Hysteresis In Planar Diodes

Solution-processed planar perovskite devices are highly desirable in a wide variety of optoelectronic applications; however, they are prone to hysteresis and current instabilities. Here we report the first perovskite–PCBM hybrid solid with significantly reduced hysteresis and recombination loss achieved in a single step. This new material displays an efficient electrically coupled microstructure: PCBM is homogeneously distributed throughout the film at perovskite grain boundaries. The PCBM passivates the key PbI3 antisite defects during the perovskite self-assembly, as revealed by theory and experiment. Photoluminescence transient spectroscopy proves that the PCBM phase promotes electron extraction. We showcase this mixed material in planar solar cells that feature low hysteresis and enhanced photovoltage. Using conductive AFM studies, we reveal the memristive properties of perovskite films. We close by positing that PCBM, by tying up both halide-rich antisites and unincorporated halides, reduces electric field-induced anion migration that may give rise to hysteresis and unstable diode behaviour.

36 MATERIALS SCIENCE↗

Gold adatom as a key structural component in self-assembled monolayers of organosulfur molecules on Au(1 1 1)

Chemisorption of organosulfur molecules, such as alkanethiols, arenethiols and disulfide compounds on gold surfaces and their subsequent self-organization is the archetypal process for molecular self-assembly on surfaces. Owing to their ease of preparation and high versatility, alkanethiol self-assembled monolayers (SAMs) have been widely studied for potential applications including surface functionalization, molecular motors, molecular electronics, and immobilization of biological molecules. Despite fundamental advances, the dissociative chemistry of the sulfur headgroup on gold leading to the formation of the sulfur–gold anchor bond has remained controversial. This paper summarizes the recent progress in the understanding of the geometrical and electronic structure of the anchor bond. Particular attention is drawn to the involvement of gold adatoms at all stages of alkanethiol self-assembly, including the dissociation of the disulfide (S–S) and hydrogen-sulfide (S–H) bonds and subsequent formation of the self-assembled structure. Gold adatom chemistry is proposed here to be a unifying theme that explains various aspects of the alkanethiol self-assembly and reconciles experimental evidence provided by scanning probe microscopy and spectroscopic methods of surface science. Finally, while several features of alkanethiol self-assembly have yet to be revisited in light of the new adatom-based models, the successes of alkanethiol SAMs suggest that adatom-mediated surface chemistry may be a viable future approach for the construction of self-assembled monolayers involving molecules which do not contain sulfur.

36 MATERIALS SCIENCE↗

The Role of Gold Adatoms and Stereochemistry in Self-Assembly of Methylthiolate on Au(111)

On the basis of high resolution STM images and DFT modeling, we have resolved low- and high-coverage structures of methylthiolate (CH3S) self-assembled on the Au(111) surface. The key new finding is that the building block of all these structures has the same stoichiometry of two thiolate species joined by a gold adatom. The self-arrangement of the methylthiolate?adatom complexes on the surface depends critically on their stereochemical properties. Variations of the latter can produce local ordering of adatom complexes with either (3 x 4) or (3 x 4{radical}3) periodicity. A possible structural connection between the (3 x 4{radical}3) structure and commonly observed ({radical}3 x {radical}3)R30{sup o} phase in methylthiolate self-assembled monolayers is developed by taking into account the reduction in the long-range order and stereochemical isomerization at high coverage. We also suggest how the observed self-arrangements of methylthiolate may be related to the c(4 x 2) phase of its longer homologues.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗