Search NASA⌕ Search

Engineering topics

Vu, Anh

Publications and source records attributed to Vu, Anh.

Unraveling the Structure and Composition of Li 4 Mn 2 O 4.5 (Li 2 O·Li 0.667 Mn 1.333 O 2 ) Electrodes for Lithium Batteries Using a High-Temperature Synthesis Approach

This paper addresses the debate about the composition and structure of a lithium-rich manganese oxide electrode with a fully disordered rock salt component, Li 4 Mn 2 O 5 (or Li 2 O·2LiMnO 2 ), first reported by Freire et al. in 2016; it is typically prepared by a high-energy ball milling procedure. It has now been demonstrated that, when prepared at 800°C, the formula of this compound is Li 4 Mn 2 O 4.5 , alternatively Li 2 O·Li 0.667 Mn 1.333 O 2 , or close thereto. The cubic, disordered Li 0.667 Mn 1.333 O 2 (or Li 0.333 Mn 0.667 O) rock salt component, in which the manganese ions adopt an average oxidation state of 2.5+, transforms to a clearly-defined spinel configuration during electrochemical cycling. The electrochemical activation process that occurs during the initial charge reaction includes the oxidation of the manganese ions by oxygen released by the Li 2 O component between 4.5 and 4.6 V. In complete contrast, nickel- and nickel-cobalt-substituted electrodes, such as Li 2 O·2LiMn 0.5 Ni 0.5 O 2 (Li 4 MnNiO 5 ) and Li 2 O·2LiMn 0.475 Ni 0.475 Co 0.050 O 2 (Li 4 Mn 0.95 Ni 0.95 Co 0.10 O 5 ), in which the manganese ions adopt a tetravalent state, have completely disordered rock salt components that are electrochemically inactive.

25 ENERGY STORAGE↗

Room-temperature fabrication of garnet-type solid-electrolyte: Optimizing particle size for high ionic conductivity

Dense and uniform Li 6.25 Al 0.25 La 3 Zr 2 O 12 (Al-doped LLZO) solid-electrolyte film of ~24 µm thickness is successfully fabricated by room temperature aerosol deposition (AD) method. The process optimization study revealed that careful control of particle size and morphology is one of critical determinants in the development of a compact AD membrane. Notably, our method facilitated an impressive ionic conductivity of approximately 10 –5 S cm –1 , bypassing the necessity for post-annealing processes, a milestone in itself. However, it is hypothesized that the attained conductivity is somewhat restrained by factors such as smaller grain size and potential surface degradation due to moisture exposure during fabrication, indicating avenues for further research. Looking forward, detailed investigations into the film's microstructure and its impact on transport properties will be a focal point, alongside potential enhancements through post-annealing and particle coating strategies. Finally, this research hints at a promising trajectory for the development of high-efficiency solid-state battery technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coatings for cathode active materials

A cathode active material includes a plurality of cathode active compound particles and a coating disposed over each of the cathode active compound particles. The coating includes a lithium (Li)-ion conducting oxide containing lanthanum (La) and titanium (Ti).

Wu, Huiming↗

Evaluation of Cathode Materials with Lithium-Metal Anodes: Baseline Performance and Protocol Standardization of Coin Cells

The collaborative evaluation of electrode materials across multiple research entities requires standardized electrochemical testing protocols to produce reliable, one-to-one comparisons between different systems of interest. Similar to the work done by Long et al. on protocol standardization for coin-cell testing with graphite anodes [J. Electrochem. Soc., 163, A2999, (2016)], here we introduce two standardized testing protocols designed to quickly evaluate important electrochemical properties of cathode materials using lithium-metal anodes. The two protocols measure kinetic and thermodynamic capacity losses, rate- and voltage-dependent cycling capacities, instabilities at high voltage and high cycling rate, and overpotentials at various states of charge. We then apply these protocols to four commercially available cathode materials to establish benchmark performance metrics that can be used to screen and evaluate new cathode materials.

25 ENERGY STORAGE↗

Understanding Lithium Local Environments in LiMn 0.5 Ni 0.5 O 2 Cathodes: A DFT-Supported 6 Li Solid-State NMR Study

LiMn 0.5 Ni 0.5 O 2 has been plagued by the structural failure driven by the irreversible phase change upon subsequent cycling and the structural degradation caused by the seemingly unavoidable Li/Ni exchange. This begs for a better understanding of the correlation between lithium local structures, synthesis conditions, and overall electrochemical properties of materials. In this study, we use density functional theory (DFT) to assist experimental 6 Li solid-state magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy to understand the nature and change in lithium local structures with extended annealing times (168 vs 15 h) synthesized at 900 °C. To correlate the NMR peak changes after different synthesis conditions, we calculated the NMR spectra of representative low-energy model configurations of LiMn 0.5 Ni 0.5 O 2 composition–zigzag, row, and flower structures–as well as the influence of Ni/Mn ordering and Li/Ni exchange on each spectrum using a supercell that is large enough to allow us to consider the effect of different relative configurations of adjacent transition metal (TM) layers. The analysis based on a combination of the calculated NMR and the experimental spectra suggests that most configurations contributing to the experimental spectra are in fact composed of a blend of configurations higher in energy than the classical well-ordered ground-state structures. Further, the extended annealing of LiMn 0.5 Ni 0.5 O 2 slightly enhances Ni/Mn and Li/Mn orderings while reducing the Li/Ni mixing ratio. This study shows how DFT calculations are crucial in providing a better understanding of the experimental characterization data and therefore local environments and domain structures in oxide materials, such as Li-ion battery cathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of formation protocol: Cells containing Si-Graphite composite electrodes

The effect of formation protocol was observed in tests using small pouch cells containing silicon-graphite/Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 chemistry. The time for the formation protocol was either 13.2 or 186 h for the tested cells. It is demonstrated that the “fast” formation protocol produces cells with similar performance characteristics to that of the “slow” protocol. Moreover, the solid-electrolyte interface layers from both formation protocols are stable and function analogously, albeit with different chemistry. The fast formation protocol may thus allow a more economical route to cell fabrication.

25 ENERGY STORAGE↗

Effect of Composition on the Voltage Fade Phenomenon in Lithium-, Manganese-Rich xLiMnO 3 •(1-x)LiNi a Mn b Co c O 2 : A Combinatorial Synthesis Approach

The effect of composition on the voltage fade phenomenon was probed using combinatorial synthesis methods. In compositions that have the general formula, (Li 2 MnO 3 ) a (LiNiO 2 ) b (LiMnO 2 ) c (LiCoO 2 ) d , where 0 ≤ a≤0.83, 0.15 ≤ b ≤ 0.42, 0 ≤ c ≤ 0.85, and 0 ≤ d ≤ 0.30 (a + b + c + d = 1), the dependence of features in the x-ray diffraction pattern and of voltage fade on composition were identified and mapped. The observed values of voltage fade indicated that it displayed some sensitivity to composition, but that the sensitivity was not large. The values of voltage fade were found to be amenable to statistical modeling. The model indicated that it may be possible to lower the value of voltage fade below 0.01% by adjusting the composition of the system; however, the composition is not expected to have the layered–layered structure.

combinatorial synthesis↗

Effects of cycling temperatures on the voltage fade phenomenon in 0.5Li 2 MnO 3 ·0.5LiNi 0.375 Mn 0.375 Co 0.25 O 2 cathodes

The rate of voltage fade in 0.5Li2MnO3•0.5LiNi0.375Mn0.375Co0.25O2 cathodes was measured in half-cells in a temperature range of 25 to 55°C. On the basis of the dependence of the values of the open-circuit potential with cycle count and temperature, the voltage fade phenomenon seems to consist of two chemical processes: one that can be described using a parabolic rate law and another that uses a linear-with-time law. As the cycling temperature increased, the relative contributions of the two processes changed. On the basis of the overall rate versus temperature data, we believe the two processes may be in competition with one another.

kinetics↗