Search NASA⌕ Search

Engineering topics

Wade Jackson

Publications and source records attributed to Wade Jackson.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Characterization of Low-Velocity Impact Damage in Toughened Non-Crimp Fabric Laminates

The damage response of resin-infused composites was investigated using quasi-static indentation (QSI) and instrumented drop-weight impact testing. The test specimens were composed of six layers of non-crimp fabrics where each layer contained +45°, 90°, −45°, and 0° plies. The goals of the testing were to identify damage responses that may differ from traditional thermoset materials and provide damage characterization data to evaluate current damage prediction analyses and aid improvements to current damage models. The damage was characterized using X-ray computed tomography (CT) and ultrasonic testing (UT). Incremental QSI loading was used on a single specimen to investigate damage growth in nine steps at progressively higher loads. Realtime acoustic emission data were used to determine the unloading points. Unlike typical thermoset composites, the force-displacement was smooth and showed no obvious indications of damage. The primary damage consisted of large lines of fiber fracture on the plies near the impact surface and delaminations through the thickness. Nine specimens were impacted at nominal impact energies of 25 ft-lbs, 30 ft-lbs, and 35 ft-lbs. The force histories at each energy followed nearly identical paths. Again, no obvious signs of damage were observed in any of the force histories. The general damage response in the dynamic tests was similar to the QSI-loaded specimens. However, repeat specimens impacted with a given impact energy showed variations in the damage. Some characteristics of the damage response were different than those typically observed in thermoset composites and will need to be evaluated using current analysis methods.

Composite Materials↗
NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗
NASA NTRS2023

Characterization of Low-Velocity Impact Damage in Thermoplastic Laminated Composites

The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.

Composite Materials↗
NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗
NASA NTRS2023

Characterization of Low-Velocity Impact Damage in Thermoplastic Laminated Composites

The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.

Composite Materials↗
NASA NTRSDate not supplied

Multiscale Failure Analysis of a 3D Woven Unit Cell Containing Defects

Multiscale failure simulations have been performed for a Three-dimensional woven composite unit cell considering five, or more, length scales spanning the woven composite mesoscale to the sub-microscale voids. The multiscale recursive micromechanics approach, which enables recursive integration of general micromechanics theories over an arbitrary number of length scales, has been employed within the NASA Multiscale Analysis Tool. The multiscale model uses both the generalized method of cells and Mori-Tanaka micromechanics theories, and considers failure in the constituent materials using a simple damage model. Baseline results, containing distributed voids, are compared to uniaxial experimental data for an AS4 carbon fiber/ RTM6 epoxy matrix 3D orthogonal woven composite with good agreement in terms of global stiffness and global failure stress. The simulations demonstrate that the 3D woven composite exhibits damage tolerance through sustaining increasing axial load far beyond the first initiation of damage. The multiscale model is used to examine the nonlinear response of the material to other loading conditions. Case studies, motivated by X-ray computed tomography data, are presented on the effects of manufacturing induced voids and cracks.

3D woven↗
NASA NTRSDate not supplied

Critical Progressive Damage Analysis Model Features for Low-Velocity Impact on Thermoset and Thermoplastic Panels

A previous verification and validation framework evaluated the ability of various progressive damage analysis (PDA) tools to predict the mechanical response and damage state in post-buckled stiffened aerospace structures composed of fiber-reinforced thermoset composite materials. Herein, the ability of PDA tools to predict damage in thermoplastic composite materials subject to low-velocity impact (LVI) loading has been assessed. LVI tests and analyses have been conducted for similar panels, comprising thermoset or thermoplastic composite materials. Preliminary test/analysis correlations revealed that using the same combination of PDA model features and finite element model-building guidelines for the thermoset and thermoplastic LVI specimens resulted in underprediction of matrix crack lengths and delaminated area in the thermoplastic analyses despite yielding good correlations for the thermoset specimens. In this paper, the quality of the test/analysis correlations for analyses of thermoplastic LVI specimens performed with different combinations of PDA model features using the NASA CompDam material model are presented. Model features that were assessed in terms of effect on the quality of the test/analysis correlation include the representation of damageable interfaces, residual thermal stresses, and fiber damage.

Frank Leone↗
NASA NTRSDate not supplied

Critical Progressive Damage Analysis Model Features for Low-Velocity Impact on Thermoset and Thermoplastic Panels

A previous verification and validation framework evaluated the ability of various progressive damage analysis (PDA) tools to predict the mechanical response and damage state in post-buckled stiffened aerospace structures composed of fiber-reinforced thermoset composite materials. Herein, the ability of PDA tools to predict damage in thermoplastic composite materials subject to low-velocity impact (LVI) loading has been assessed. LVI tests and analyses have been conducted for similar panels, comprising thermoset or thermoplastic composite materials. Preliminary test/analysis correlations revealed that using the same combination of PDA model features and finite element model-building guidelines for the thermoset and thermoplastic LVI specimens resulted in underprediction of matrix crack lengths and delaminated area in the thermoplastic analyses despite yielding good correlations for the thermoset specimens. In this paper, the quality of the test/analysis correlations for analyses of thermoplastic LVI specimens performed with different combinations of PDA model features using the NASA CompDam material model are presented. Model features that were assessed in terms of effect on the quality of the test/analysis correlation include the representation of damageable interfaces, residual thermal stresses, and fiber damage.

Frank Leone↗
NASA NTRSDate not supplied

Low-Velocity Impact Analyses of Composite Panels Using Cohesive Zone Modeling and Continuum Damage Mechanics

A parametric study was conducted to gage the sensitivity of simulations of low-velocity impacts on laminated composite panels to various finite element model and material model features. The material model used in this parametric study was previously verified and validated for conducting progressive damage analyses of post-buckled composite structures subjected to quasi-static loading conditions. Based on the results of this parametric study, updates have been made to a progressive damage analysis material model and the best practices for its application. Experimental results are compared to computational results obtained with and without the updates to the models. Both thermoset and thermoplastic fiber-reinforced materials are considered. The resulting enhancements to the material model are presented in detail.

Frank Leone↗
NASA NTRSDate not supplied

Characterization of Low-Velocity Impact Damage in Toughened Non-Crimp Fabric Laminates

The damage response of resin-infused composites was investigated using quasi-static indentation (QSI) and instrumented drop-weight impact testing. The test specimens were composed of six layers of non-crimp fabrics where each layer contained +45°, 90°, −45°, and 0° plies. The goals of the testing were to identify damage responses that may differ from traditional thermoset materials and provide damage characterization data to evaluate current damage prediction analyses and aid improvements to current damage models. The damage was characterized using X-ray computed tomography (CT) and ultrasonic testing (UT). Incremental QSI loading was used on a single specimen to investigate damage growth in nine steps at progressively higher loads. Realtime acoustic emission data were used to determine the unloading points. Unlike typical thermoset composites, the force-displacement was smooth and showed no obvious indications of damage. The primary damage consisted of large lines of fiber fracture on the plies near the impact surface and delaminations through the thickness. Nine specimens were impacted at nominal impact energies of 25 ft-lbs, 30 ft-lbs, and 35 ft-lbs. The force histories at each energy followed nearly identical paths. Again, no obvious signs of damage were observed in any of the force histories. The general damage response in the dynamic tests was similar to the QSI-loaded specimens. However, repeat specimens impacted with a given impact energy showed variations in the damage. Some characteristics of the damage response were different than those typically observed in thermoset composites and will need to be evaluated using current analysis methods.

Composite Materials↗