Engineering topics

Waggoner, E. G.

Publications and source records attributed to Waggoner, E. G..

13 records

NASA NTRS1990

Prediction of effects of wing contour modifications on low-speed maximum lift and transonic performance for the EA-6B aircraft

Computational predictions of the effects of wing contour modifications on maximum lift and transonic performance were made and verified against low speed and transonic wind tunnel data. This effort was part of a program to improve the maneuvering capability of the EA-6B electronics countermeasures aircraft, which evolved from the A-6 attack aircraft. The predictions were based on results from three computer codes which all include viscous effects: MCARF, a 2-D subsonic panel code; TAWFIVE, a transonic full potential code; and WBPPW, a transonic small disturbance potential flow code. The modifications were previously designed with the aid of these and other codes. The wing modifications consists of contour changes to the leading edge slats and trailing edge flaps and were designed for increased maximum lift with minimum effect on transonic performance. The prediction of the effects of the modifications are presented, with emphasis on verification through comparisons with wind tunnel data from the National Transonic Facility. Attention is focused on increments in low speed maximum lift and increments in transonic lift, pitching moment, and drag resulting from the contour modifications.

Allison, Dennis O.↗

NASA NTRS1989

Computational support of the X-29A Advanced Technology Demonstrator flight experiment

Issues and questions associated with the forward swept wing and closely coupled canard are addressed. The primary focus will be on research questions which must be addressed to obtain high quality ground and flight test data. These data will be used in conjunction with computational predictions to complement the analyses required to comprehensively understand the interacting technologies.

Waggoner, E. G.↗

NASA NTRS1987

EA-6B high-lift wing modifications

NASA-Langley has accomplished the computational design and experimental verification of EA-6B aircraft wing modifications for improved high lift capability. The modifications are comparatively simple, and attempt to improve low speed high lift performance while maintaining high speed cruise efficiency. Several two- and three-dimensional low speed and transonic computational techniques were employed, together with extensive wind tunnel tests. The modified inboard and outboard edge slat/flap system sections yielded efficiency improvements that were verified by three-dimensional wind tunnel experiments to amount to an 11-percent wing-body lift coefficient enhancement at low speed.

Waggoner, E. G.↗

NASA NTRS1986

X-29 Flight Test Program including wind tunnel and computational support

A cooperative effort has been defined between NASA-Ames/Dryden Flight Research Facility and NASA-Langley Research Center in support of the X-29A Advanced Technology Demonstrator. The effort involves three phases: flight testing, wind-tunnel testing in the National Transonic Facility, and computational support of each experimental phase. These efforts are primarily aimed at understanding the complex flow phenomena and component interactions associated with the X-29A. Each phase of the effort is discussed in detail and initial data comparisons are presented. In summary, the synergistics effects of the complementary phases are identified, which will enhance the understanding of the unique aerodynamics of the X-29A.

Waggoner, E. G.↗

NASA NTRS1986

Design of a natural laminar flow wing for a transonic corporate transport

Two- and three-dimensional computational methods were used to design a wing for a transonic corporate transport that had significant runs of laminar flow on both upper and lower wing surfaces at the cruise condition. The airfoil was derived from a low-speed laminar-flow section. The contour was systematically modified based on results from a two-dimensional transonic code to give favorable pressure gradients to 50-percent chord on the upper surface and 65-percent chord on the lower surface. Three-dimensional transonic codes were used to determine the wing twist and to evaluate the aerodynamic characteristics of the complete configuration at various flight conditions. A leading-edge modification for improved stall characteristics was also designed. The theoretical pressure distributions for the final airfoil correlated well with results from wind-tunnel tests.

Campbell, R. L.↗

NASA NTRS1985

Computational wing design in support of an NLF variable sweep transition flight experiment

A natural laminar flow outer panel wing glove has been designed for a variable sweep fighter aircraft using state-of-the-art computational techniques. Testing of the design will yield wing pressure and boundary-layer data under actual flight conditions and environment. These data will be used to enhance the understanding of the interaction between crossflow and Tollmien-Schlichting disturbances on boundary-layer transition. The outer wing panel was contoured such that a wide range of favorable pressure gradients could be obtained on the wing upper surface. Extensive computations were performed to support the design effort which relied on two- and three-dimensional transonic design and analysis techniques. A detailed description of the design procedure that evolved during this study is presented. Results on intermediate designs at various stages in the design process demonstrate how the various physical and aerodynamic constraints were integrated into the design. Final results of the glove design analyzed as part of the complete aircraft configuration with a full-potential wing/body analysis code indicate that the aerodynamic design objectives were met.

Waggoner, E. G.↗

NASA NTRS1985

A faster 'transition' to laminar flow

A discussion is given of the ongoing research related to laminar flow airfoils, nacelles, and wings where the laminar flow is maintained by a favorable pressure gradient, surface suction or a combination of the two. Design methologies for natural laminar flow airfoil sections and wings for both low and high speed applications are outlined. Tests of a 7-foot chord, 23-deg sweep laminar flow-control airfoil at high subsonic Mach numbers are described, along with the associated stability theory used to design the suction system. The state-of-the-art of stability theory is simply stated and a typical calculation illustrated. In addition, recent computer simulations of transition using the time dependent Navier-Stokes equations are briefly described. Advances in wind tunnel capabilities and instrumentation will be reviewed, followed by the presentation of a few results from both wind tunnels and flight. Finally, some suggestions for future work will complete the paper.

Bobbitt, P. J.↗

NASA NTRS1985

Potential flow calculations and preliminary wing design in support of an NLF variable sweep transition flight experiment

NASA Langley and NASA Ames-Dryden have defined a variable-sweep transition-flight experiment utilizing the F-14 aircraft to enhance understanding of the interaction of crossflow and Tollmien-Schlichting instabilities on a laminar-boundary-layer transition. The F-14 wing outer panel will be modified to generate favorable pressure gradients on the upper wing surface over a wide range of flight conditions. Extensive computations have been performed using two-dimensional and three-dimensional transonic analysis codes. Flight-test and computational data are compared and shown to validate the applicability of the three-dimensional codes (WBPPW and TAWFIVE). In addition, results from two preliminary glove designs derived from two different approaches to the design problem are presented. Advantages and disadvantages of each approach are identified, and it is concluded that coupling an analysis code with an automated design procedure yields a powerful code with distinct advantages over a 'cut-and-dry' approach.

Waggoner, E. G.↗

NASA NTRS1984

Validation of a transonic analysis code for use in preliminary design of advanced transport configurations

The WBPPW code has the capability of analyzing flow-field effects about configurations which include wing pylons and engine nacelles or pods in addition to the basic wing/fuselage combination. Using the concept of grid embedding, the code solves the extended small disturbance transonic flow equation for complex flow interactions of the various configuration components. A general description of the code and solution algorithm is included. Results are presented and compared with experiment for various configurations which encompass the code capabilities. These include wing planform and wing contour modifications and variations in nacelle position beneath a high-aspect-ratio wing. Results are analyzed in the light of preliminary design, where the capability to accurately compute flow-field effects resulting from various configuration perturbations is important. The comparisons show that the computational results are sensitive to subtle design modifications and that the code could be used as an effective guide during the design process for transport configurations.

Waggoner, E. G.↗

NASA NTRS1983

Computational analysis for an advanced transport configuration with engine nacelle

A small-disturbance transonic analysis code is used to calculate the flow-field effects of adding an engine nacelle to a wing/body configuration. Analyses are performed on an advanced transport configuration with and without engine nacelles. Two nacelle shapes are analyzed and the effects of the nacelle installation on pressure distributions are compared with experimental results obtained by shifting the nacelle longitudinally and vertically relative to the wing. Effects of varying the nacelle installation yaw angle are also analyzed and compared with experimental data. These comparisons show that the analysis code is adequately sensitive to variations in nacelle shape, longitudinal and vertical location beneath the wing, and the nacelle installation yaw angle. Results indicate that the code can be used as an effective guide during the design process.

Waggoner, E. G.↗

NASA NTRS1982

Transonic three-dimension viscous-inviscid interaction for wing-body configuration analysis

A three-dimensional small disturbance transonic analysis code has been coupled with a three-dimensional integral boundary layer code. A scheme was developed to interact the two codes through the use of a controlling module. The resulting hybrid code does not increase the costs or computer core requirements over that of the previous capabilities of the analysis code, which used a two-dimensional boundary layer analysis to model viscous effects. Several configurations have been analyzed and results compared against both experimental data and computational results using the two-dimensional viscous model. Results indicate good agreement with experimental data when using the three-dimensional interaction scheme, with the most marked improvement in the correlations observed for wing pressure coefficient predictions in the lower surface cusp region for supercritical wings.

Waggoner, E. G.↗

NASA NTRS1978

Computational wing optimization and comparisons with experiment for a semi-span wing model

A computational wing optimization procedure was developed and verified by an experimental investigation of a semi-span variable camber wing model in the NASA Ames Research Center 14 foot transonic wind tunnel. The Bailey-Ballhaus transonic potential flow analysis and Woodward-Carmichael linear theory codes were linked to Vanderplaats constrained minimization routine to optimize model configurations at several subsonic and transonic design points. The 35 deg swept wing is characterized by multi-segmented leading and trailing edge flaps whose hinge lines are swept relative to the leading and trailing edges of the wing. By varying deflection angles of the flap segments, camber and twist distribution can be optimized for different design conditions. Results indicate that numerical optimization can be both an effective and efficient design tool. The optimized configurations had as good or better lift to drag ratios at the design points as the best designs previously tested during an extensive parametric study.

Waggoner, E. G.↗

NASA NTRS1978

Computational wing optimization and wind tunnel test of semi-span model

A computational transonic wing design procedure has been developed and verified by a wind tunnel test of a variable camber semi-span wing model. The Bailey-Ballhaus transonic potential flow analysis code linked to Vanderplaat's constrained minimization routine was used to optimize test configurations at 0.9 Mach number. Based on wind tunnel test results, computationally optimized designs were as efficient as the best configurations determined by previous parametric testing and performed better at off-design points. Wind tunnel wing pressures agreed well with predictions from the improved Bailey-Ballhaus code at moderate CL's. Computational optimization was shown to be an effective transonic wing design tool.

Haney, H. P.↗