Search NASA⌕ Search

Engineering topics

Waldron, C D

Publications and source records attributed to Waldron, C D.

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1941

Flow coefficients of monosleeve valves

The flow coefficients of the intake and the exhaust ports of a sleeve-valve cylinder were measured by attaching the cylinder to a large tank and measuring the changes in pressure and temperature in the tank that were caused by short periods of air flow through the valve ports. The derivation of the equations on which the flow coefficients are based is given. The distribution of total pressure in the arms of the sleeve-valve intake manifold was measured. The arms are found to have as little as 75 percent of the total pressure within the manifold entrance.

Waldron, C D↗
NASA NTRS1939

Intermittent-flow coefficients of a poppet valve

Flow coefficients were determined for the inlet valve of a modern air-cooled cylinder during operation of the valve. The cylinder head with valves was mounted on a large tank that could be evacuated. Operating the valve with a rotating cam allowed air to flow through the valve into the evacuated tank. The change of pressure in the tank was a measure of the amount of air flowing though the valve in a given number of cycles. The flow coefficients were determined from the pressure across the valve, the quantity of air flowing, and the valve-lift curve. Coefficients were measured with lifts of 0.1 to 0.6 inch and speeds of 130 to 1,200 r.p.m. The results obtained with intermittent flow were compared with the results of tests made with steady flow through this cylinder head. This comparison indicated that steady-flow coefficients can be used for intermittent flow.

Waldron, C D↗
NASA NTRS1937

Effects of Air-Fuel Spray and Flame Formation in a Compression-Ignition Engine

High-speed motion pictures were taken at the rate of 2,500 frames per second of the fuel spray and flame formation in the combustion chamber of the NACA combustion apparatus. The compression ratio was 13.2 and the speed 1,500 revolutions per minute. An optical indicator was used to record the time-pressure relationship in the combustion chamber. The air-fuel ratio was varied from 10.4 to 365. The results showed that as the air-fuel ratio was increased definite stratification of the charge occurred in the combustion chamber even though moderate air flow existed. The results also showed the rate of vapor diffusion to be relatively slow.

Rothrock, A M↗
NASA NTRS1937

Effect of Nozzle Design on Fuel Spray and Flame Formation in a High-Speed Compression-Ignition Engine

Fuel was injected from different type of injection nozzles into the combustion chamber of the NACA combustion apparatus, operated as a compression-ignition engine. High speed motion pictures were taken of the fuel sprays and combustion. Single-orifice nozzles of 0.008, 0.020, and 0.040 inch diameter, and multiorifice nozzles having 2, 6, and 16 orifices were tested. Nozzles having impinging jets and slit orifices were also included. The photographs indicate that the rate of vapor diffusion from the spray is comparatively slow and that this slow rate of diffusion for combustion chambers with little or no air flow prevents the compression-ignition engine from giving the high performance inherent in the high compression ratios. The sprays from the multiorifice nozzles destroyed the air movement to a greater extent than did those from single orifice nozzles. It is concluded that high performance cannot be realized until the methods of distributing the fuel are improved by means of the injection-nozzle design, air flow, or both.

Rothrock, A M↗
NASA NTRS1937

Fuel Spray and Flame Formation in a Compression-Ignition Engine Employing Air Flow

The effects of air flow on fuel spray and flame formation in a high-speed compression-ignition engine have been investigated by means of the NACA combustion apparatus. The process was studied by examining high-speed motion pictures taken at the rate of 2,200 frames a second. The combustion chamber was of the flat-disk type used in previous experiments with this apparatus. The air flow was produced by a rectangular displacer mounted on top of the engine piston. Three fuel-injection nozzles were tested: a 0.020-inch single-orifice nozzle, a 6-orifice nozzle, and a slit nozzle. The air velocity within the combustion chamber was estimated to reach a value of 425 feet a second. The results show that in no case was the form of the fuel spray completely destroyed by the air jet although in some cases the direction of the spray was changed and the spray envelope was carried away by the moving air. The distribution of the fuel in the combustion chamber of a compression-ignition engine can be regulated to some extent by the design of the combustion chamber, by the design of the fuel-injection nozzle, and by the use of air flow.

Rothrock, A M↗
NASA NTRS1936

Some Effects of Injection Advance Angle, Engine-Jacket Temperature, and Speed on Combustion in a Compression-Ignition Engine

An optical indicator and a high-speed motion-picture camera capable of operating at the rate of 2,000 frames per second were used to record simultaneously the pressure development and the flame formation in the combustion chamber of the NACA combustion apparatus. Tests were made at engine speeds of 570 and 1,500 r.p.m. The engine-jacket temperature was varied from 100 degrees to 300 degrees F. And the injection advance angle from 13 degrees after top center to 120 degrees before top center. The results show that the course of the combustion is largely controlled by the temperature and pressure of the air in the chamber from the time the fuel is injected until the time at which combustion starts and by the ignition lag. The conclusion is presented that in a compression-ignition engine with a quiescent combustion chamber the ignition lag should be the longest that can be used without excessive rates of pressure rise; any further shortening of the ignition lag decreased the effective combustion of the engine.

Rothrock, A M↗
NASA NTRS1934

A Preliminary Motion-picture Study of Combustion in a Compression-ignition Engine

Motion pictures were taken at 1,850 frames per second of the spray penetration and combustion occurring in the N.A.C.A. combustion apparatus arranged to operate as a compression-ignition engine. Indicator cards were taken simultaneously with the motion pictures by means of the N.A.C.A. optical indicator. The motion pictures showed that when ignition occurred during injection it started in the spray envelope. If ignition occurred after injection cut-off, however, and after considerable mixing had taken place, it was impossible to predict where the ignition would start. The pictures also showed that ignition usually started at several points in the combustion chamber. With this apparatus, as the injection advance angle increased from 0 degrees to 40 degrees before top center, the rate of flame spread increased and the duration of the burning decreased.

Buckley, E C↗
NASA NTRS1933

Fuel Vaporization and Its Effect on Combustion in a High-Speed Compression-Ignition Engine

The tests discussed in this report were conducted to determine whether or not there is appreciable vaporization of the fuel injected into a high-speed compression-ignition engine during the time available for injection and combustion. The effects of injection advance angle and fuel boiling temperature were investigated. The results show that an appreciable amount of the fuel is vaporized during injection even though the temperature and pressure conditions in the engine are not sufficient to cause ignition either during or after injection, and that when the conditions are such as to cause ignition the vaporization process affects the combustion. The results are compared with those of several other investigators in the same field.

Rothrock, A M↗
NASA NTRS1932

Effect of Engine Operating Conditions on the Vaporization of Safety Fuels

Tests were conducted with the N.A.C.A. combustion apparatus to determine the effect of compression ratio and engine temperature on the vaporization of a hydrogenated "safety fuel" during the compression stroke under conditions similar to those in a spark-ignition engine. The effects of fuel boiling temperature on vaporization using gasoline, safety fuel, and Diesel fuel oil was also investigated. The results show that increasing the compression ratio has little effect on the rate of fuel vaporization, but that increasing the air temperature by increasing the engine temperature increases the rate of fuel vaporization. The results also show that the vaporized fuel forms a homogeneous mixture with the air more rapidly that does the atomized fuel spray.

Rothrock, A M↗
NASA NTRS1931

Some Characteristics of Fuel Sprays at Low-injection Pressures

This report presents the results of tests conducted at the Langley Memorial Aeronautical Laboratory, Langley Field, Va., to determine some of the characteristics of the fuel sprays obtained from an 0.008-inch and a 0.020-inch open nozzle when injection pressures from 100 to 500 pounds per square inch were used. Fuel oil and gasoline were injected into air at densities of atmospheric land 0.325 pound per cubic foot. It was found that the penetration rate at these low pressures was about the same as the rate obtained with higher pressures. Spray cone-angles were small and individual oil drops were visible in all the sprays. Gasoline and fuel oil sprays had similar characteristics.

Rothrock, A M↗