Engineering topics

Wallen, Zane G.

Publications and source records attributed to Wallen, Zane G..

5 records

DOE OSTI2024

Modeling and design of a separate effects irradiation test targeting fission gas release from Cr-doped UO 2

Fission gas release (FGR) from nuclear fuel during operation can diminish heat transfer properties across the pellet-cladding gap and increase the fuel rod internal pressure, thereby posing a concern to fuel reliability and safety during an accident. Enlarging the fuel grain size, which has been shown to improve fission gas retention, can be achieved by doping the fuel feedstock prior to sintering. In this work, the BISON fuel performance code was used to predict FGR from undoped and chromia-doped UO 2 (referred to as Cr-doped UO 2 ) fuel specimens with different grain sizes and across various temperatures. The BISON models identified the irradiation conditions for which FGR is most significant, and a separate effects irradiation experiment in the High Flux Isotope Reactor (HFIR) was then developed targeting those conditions. Further, the experiment leveraged the MiniFuel irradiation capability at Oak Ridge National Laboratory and consisted of 12 fuel specimens of varying grain size and Cr content. A coupling scheme between BISON FGR results and the ANSYS finite element thermal model used for experiment design was formulated to predict cumulative FGR from each fuel specimen based on expected irradiation temperature histories. The fuel samples were fabricated and characterized as a part of this work, and the fuel compositions modeled in BISON were representative of the specimens used in the experiment. This combined modeling and experimental effort aims to study the effect of fuel grain size and Cr content on FGR and to provide simulated BISON FGR results that can be used for future model validation activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

ROADRUNNER MiniFuel Experiment: Irradiation Target Design and Sample Characterization

High-density uranium nitride (UN) is a fuel candidate for several advanced nuclear reactor designs currently under development. Because there are limited UN performance data relative to fuel fabrication impurity and density variation, an irradiation campaign has been developed as part of a collaborative effort among the University of Texas at San Antonio (UTSA), Westinghouse Electric Company, Oak Ridge National Laboratory (ORNL), and Los Alamos National Laboratory (LANL) under the Nuclear Science User Facilities program. This project, entitled ROADRUNNER, or Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments, aimsto support UN fuel qualification for advanced reactors by investigating the impact of density and impurity variations on UN performance as a function of irradiation temperature and burnup. The MiniFuel experiment vehicle developed by ORNL, which leverages the High Flux Isotope Reactor, was selected to perform this accelerated separate-effects irradiation testing. The experiment test matrix consists of six MiniFuel targets containing miniature UN fuel disks, and targets three distinct burnup levels (37.5, 60, and 75 MWd/kg U) and three distinct temperatures (600, 900, and 1200°C). Neutronics and thermal analyses were performed to determine the experimental parameters needed to meet the desired irradiation conditions and to predict the experiment components temperatures. UN pellets were fabricated at LANL with tightly controlled parameters to produce specimens with three distinct densities and three levels of carbon content. The pellets were then thinned down by UTSA to the experiment-required thickness. The pre-characterization of the specimens includes density measurements, carbon and oxygen contents, microstructure analysis, and x-ray computed tomography. The selected specimens will be assembled into the MiniFuel experiment, and the first ROADRUNNER MiniFuel targets are intended for HFIR insertion during the Fall of 2024. After irradiation, the targets will be shipped to ORNL’s hot cell facility for disassembly. The post-irradiation examination on the fuel specimens includes fission gas release measurements, visual inspection, fuel swelling measurements, gamma spectroscopy, and microstructure analysis. The data collected post-irradiation will be used to develop fuel performance models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Simulation of a TRISO MiniFuel irradiation experiment with data-informed uncertainty quantification

An irradiation experiment using tristructural isotropic (TRISO) fuel particles and the miniature fuel (MiniFuel) irradiation vehicle was performed in Oak Ridge National Laboratory’s High Flux Isotope Reactor (HFIR) to support development of the Kairos Power fluoride salt–cooled, high-temperature reactor (KP-FHR). Here, this paper describes modeling predictions of temperatures and fuel burnup for the as-built experiment. An uncertainty quantification (UQ) analysis was performed to determine the effect of TRISO particle volume and position on the temperature predictions at various fuel heat generation rates (HGRs). This UQ study utilized fuel kernel position and volume measurements previously collected using X-ray computed tomography (XCT) techniques and Monte Carlo sampling methods to generate fuel compact cases that were then analyzed using a finite element thermal model. The UQ analysis indicated that uncertainty in calculated temperatures caused by varying TRISO particle arrangement is relatively small, even at high fuel HGR. Final predictions of particle temperatures throughout the irradiation are shown to be relevant to KP-FHR normal and off-normal operating conditions and to previous TRISO irradiation experiments. The combination of XCT with UQ analyses will inform post-irradiation examination (PIE) of the irradiated fuel compacts, and these analyses can be used to develop fuel performance models for coated particle fuel forms. Both PIE of separate-effects irradiation data and enhanced fuel performance modeling support accelerated qualification of TRISO fuels for a broad range of advanced reactor applications. The novel approach demonstrated here of measuring TRISO particle configurations with XCT methods and generating representative fuel compacts for finite element modeling and UQ analysis could be leveraged by the broader particle fuel community in the development of other TRISO fuel experiments in which these variables may have a significant impact on key outcomes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Irradiation of MiniFuel Targets Bearing TRISO Fuel Compacts (Status Report)

Irradiation testing of MiniFuel compacts bearing tristructural isotropic (TRISO) fuel particles was performed at Oak Ridge National Laboratory (ORNL) to support the development of Kairos Power’s (KP’s) fluoride salt–cooled high-temperature reactor concept. The fuel compacts were fabricated with TRISO fuel particles of different types—including low-enriched uranium oxide, uranium carbide (LEUCO), natural uranium oxide, uranium carbide (NUCO), and low-enriched uranium dioxide (LEUO 2 )—and inserted into MiniFuel irradiation targets. Five targets were assembled and inserted in the High Flux Isotope Reactor (HFIR) for four cycles. The data collected post-irradiation will provide experimental input to validate TRISO fuel performance models for high particle power operations. This report summarizes the completion of the HFIR irradiation, the as-irradiated numerical analysis, and the post-irradiation work performed to date. This work was performed under the Nuclear Science User Facility program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Modifications to MiniFuel Vehicle Needed to Enable Higher Temperature UO 2 Irradiation Capabilities (Summarizing Issue Report)

The Advanced Fuels Campaign (AFC) within the US Department of Energy Office of Nuclear Energy (DOE-NE) supported the conception and initial demonstration of the miniature fuel (MiniFuel) irradiation capability in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. These MiniFuel experiments are a key component of a larger effort to accelerate the qualification of novel fuel concepts and to reduce uncertainty in fuel performance models. MiniFuel experiments to date have been conducted in HFIR’s outer vertical experimental facility (VXF) positions. However, there is motivation to achieve irradiation temperatures and fuel burnup accumulation rates greater than what is achievable in the VXF positions to explore high-temperature phenomena and further accelerate fuel qualification. Therefore, MiniFuel irradiation experiments are being considered in HFIR’s removable beryllium region, which is closer to the fueled core than the VXF region. This report summarizes the design modifications to the MiniFuel irradiation vehicle needed to enable high-temperature (i.e., >1,000°C) irradiation tests with rapid burnup accumulation.

10 SYNTHETIC FUELS↗