Search NASA⌕ Search

Engineering topics

Wallner, Thomas

Publications and source records attributed to Wallner, Thomas.

At least 55 records · Page 3

Use of Adaptive Injection Strategies to Increase the Full Load Limit of RCCI Operation

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection (DI) of a higher reactivity fuel, otherwise known as reactivity controlled compression ignition (RCCI), has been shown as a method to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NO x emissions, and high indicated thermal efficiency. A key requirement for extending to high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13 l multicylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and DI of diesel fuel. Engine testing was conducted at an engine speed of 1200 rpm over a wide variety of loads and injection conditions. The impact on dual-fuel engine performance and emissions with respect to varying the fuel injection parameters is quantified within this study. The injection strategies used in the work were found to affect the combustion process in similar ways to both conventional diesel combustion (CDC) and RCCI combustion for phasing control and emissions performance. As the load is increased, the port fuel injection (PFI) quantity was reduced to keep peak cylinder pressure (PCP) and maximum pressure rise rate (MPRR) under the imposed limits. Overall, the peak load using the new injection strategy was shown to reach 22 bar brake mean effective pressure (BMEP) with a peak brake thermal efficiency (BTE) of 47.6%.

Hanson, Reed↗

Extending Lean and Exhaust Gas Recirculation-Dilute Operating Limits of a Modern Gasoline Direct-Injection Engine Using a Low-Energy Transient Plasma Ignition System

The efficiency improvement and emissions reduction potential of lean and exhaust gas recirculation (EGR)-dilute operation of spark-ignition gasoline engines is well understood and documented. However, dilute operation is generally limited by deteriorating combustion stability with increasing inert gas levels. The combustion stability decreases due to reduced mixture flame speeds resulting in significantly increased combustion initiation periods and burn durations. A study was designed and executed to evaluate the potential to extend lean and EGR-dilute limits using a low-energy transient plasma ignition system. The low-energy transient plasma was generated by nanosecond pulses and its performance compared to a conventional transistorized coil ignition (TCI) system operated on an automotive, gasoline direct-injection (GDI) single-cylinder research engine. The experimental assessment was focused on steady-state experiments at the part load condition of 1500 rpm 5.6 bar indicated mean effective pressure (IMEP), where dilution tolerance is particularly critical to improving efficiency and emission performance. Experimental results suggest that the energy delivery process of the low-energy transient plasma ignition system significantly improves part load dilution tolerance by reducing the early flame development period. Statistical analysis of relevant combustion metrics was performed in order to further investigate the effects of the advanced ignition system on combustion stability. Results confirm that at select operating conditions EGR tolerance and lean limit could be improved by as much as 20% (from 22.7 to 27.1% EGR) and nearly 10% (from λ = 1.55 to 1.7) with the low-energy transient plasma ignition system.

33 ADVANCED PROPULSION SYSTEMS↗

Cycle-to-Cycle Variations in Multi-Cycle Engine RANS Simulations

Reynolds-averaged Navier-Stokes (RANS) modeling is expected to deliver an ensemble-averaged result for the majority of turbulent flows. This could lead to the conclusion that multi-cycle internal combustion engine (ICE) simulations performed using RANS must exhibit a converging numerical solution after a certain number of consecutive cycles. However, for some engine configurations unsteady RANS simulations are not guaranteed to deliver an ensemble-averaged result. In this paper it is shown that, when using RANS modeling to simulate multiple engine cycles, the cycle-to-cycle variations (CCV) generated from different initial conditions at each cycle are not damped out even after a large number of cycles. A single-cylinder GDI research engine is simulated using RANS modeling and the numerical results for 20 consecutive engine cycles are evaluated for two specific operating conditions. One condition is characterized by stoichiometric operation and stable combustion (COVIMEP < 2%) and the other features dilute combustion resulting in misfire events and much higher COVIMEP. In both cases, multi-cycle RANS simulation results show cyclic variability. An in-depth analysis of the most significant physical and chemical quantities highlights that CCV are caused primarily by the variability of the in-cylinder flow. For stoichiometric combustion this does not greatly affect flame propagation, and the resulting fluctuations of the pressure traces are narrow. However, in the event of dilute combustion, the variability of the flow gains more importance, therefore delivering large cyclic fluctuations of in-cylinder pressure. Even though unsteady RANS simulations are not expected to predict as much variability in engine flows as LES, in particular for stable cases, they can still be used to capture typical combustion stability features in an internal combustion engine. This paper shows that the occurrence of CCV when using multi-cycle RANS modeling is not a numerical artifact or the effect of changes in the computational grid from cycle to cycle. Cold-flow analysis reveals that the variability of the simulated flow is intrinsic for the unsteady RANS approach and can only be damped out by increasing numerical viscosity, either by increasing the cell size or by adding up-winding. This is proved in a simplified non-ICE case such as the simulation of the vortex shredding from a cylinder in cross flow. Also, the effect of numerical viscosity on CCV is shown for multi-cycle engine simulations by using a simplified combustion model. Finally, it is shown that multi-cycle RANS can successfully predict the effect of changing specific engine parameters, such as the properties of the ignition system, on cyclic variability and combustion stability.

Scarcelli, Riccardo↗

Numerical Investigation of Spark Ignition Events in Lean and Dilute Methane/Air Mixtures using a Detailed Energy Deposition Model

It is beneficial but challenging to operate spark-ignition engines under highly lean and dilute conditions. The unstable ignition behavior can result in downgraded combustion performance in engine cylinders. Numerical approach is serving as a promising tool to identify the ignition requirements by providing insight into the complex physical/chemical phenomena. An effort to simulate the early stage of flame kernel initiation in lean and dilute fuel/air mixture has been made and discussed in this paper. The simulations are set to validate against laboratory results of spark ignition behavior in a constant volume combustion vessel. In order to present a practical as well as comprehensive ignition model, the simulations are performed by taking into consideration the discharge circuit analysis, the detailed reaction mechanism, and local heat transfer between the flame kernel and spark plug. The energy profile and the energy source geometry are investigated in detail to represent the physics of electrical discharge. It was observed in the experiments that a sufficiently high ambient pressure is necessary for a successful ignition event in the lean and dilute mixture when the spark plug gap size and primary energy input are held constant. By adopting realistic energy levels, this detailed energy deposition model showed the capability to reasonably present such ignition behavior transition. The unique combination of energy deposition profile and geometry reveals the complexity of electrical discharge during the spark ignition event. The response of the combustible gas to the energy deposition showed dependency on the volumetric energy density, energy source’s surface area, temperature gradient at the energy source boundary, as well as the heat transfer condition local to the flame kernel.

Zhang, Anqi↗

Time-resolved x-ray radiography of spark ignition plasma

Understanding the short-lived structure of the plasma that forms between the electrodes of a spark plug is crucial to the development of improved ignition models for SI engines. However, measuring the amount of energy deposited in the gas directly and non-intrusively is difficult, due to the short time scales and small length scales involved. The breakdown of the spark gap occurs at nanosecond time scales, followed by an arc phase lasting a few microseconds. Finally, a glow discharge phase occurs over several milliseconds. It is during the arc and glow discharge phases that most of the heat transfer from the plasma to the electrodes and combustion gases occurs. Light emission can be used to measure an average temperature, but micron spatial resolution is required to make localized measurements. In this paper, we present the results of a proof of concept experiment that demonstrates the use of time-resolved x-ray radiography to measure the density of the plasma in the spark gap during the glow discharge phase of a conventional transistorized coil ignition system. A focused monochromatic x-ray beam from the 7-BM beamline of the Advanced Photon Source at Argonne National Laboratory was used to make time-resolved point measurements of the projected density, which decreases as the plasma temperature increases. Multiple measurement positions were combined to produce a two-dimensional map of the projected density both inside and surrounding the spark gap. A temporal resolution of 153 ns and spatial resolution of 5 μm were achieved. A range of ambient gases, densities (1 - 3 bar) and ignition coil charging durations (1 - 2.5 ms) were considered. At least 30 repeated measurements were made for each sample point and condition. All these parameters were found to substantially alter the structure of the plasma as measured by x-ray radiography. From the projected density measurements, changes in thermal energy can be calculated. These provide a quantitative measurement of the energy deposited into the gas; this is only a small fraction of the total spark energy. The measurements demonstrate the feasibility of time-resolved x-ray radiography for the study of plasma structure and development for SI applications.

Kastengren, Alan L.↗

Cylinder-to-Cylinder Variations in Power Production in a Dual Fuel Internal Combustion Engine Leveraging Late Intake Valve Closings

Advanced internal combustion engines, although generally more efficient than conventional combustion engines, often encounter limitations in multi-cylinder applications due to variations in the combustion process. This study leverages experimental data from an inline 6-cylinder heavy-duty dual fuel engine equipped with a fully-flexible variable intake valve actuation system to study cylinder-to-cylinder variations in power production. The engine is operated with late intake valve closure timings in a dual-fuel combustion mode featuring a port-injection and a direct-injection fueling system in order to improve fuel efficiency and engine performance. Experimental results show increased cylinder-to-cylinder variation in IMEP as IVC timing moves from 570°ATDC to 610°ATDC, indicating an increasingly uneven fuel distribution between cylinders. These observations along with engine simulation models developed using GT-Power have been used to better understand the distribution of the port-injected fuel across cylinders under various operating conditions. This study revealed that the fuel distribution across cylinders in this dual fuel application is significantly affected by changes in the effective compression ratio as determined by the intake valve close timing as well as the design of the intake system (specifically the length of the intake runners). Late intake valve closures allow a portion of the trapped air and port injected fuel to flow back out of the cylinders into the intake manifold. The fuel that is pushed back in the intake manifold is then unevenly redistributed across the cylinders largely due to the dominating direction of the flow in the intake manifold. Experimental and simulation results discussing the impact of operating parameters on the fuel distribution are presented.

Kassa, Mateos↗

Comparison of RCCI Operation with and without EGR over the Full Operating Map ofa Heavy-Duty Diesel Engine

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection of a higher reactivity fuel, otherwise known as Reactivity Controlled Compression Ignition (RCCI), has been shown as a method to achieve high efficiency combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions. A key requirement for extending to high-load operation is reduce the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and direct injection of diesel fuel. Natural gas/diesel RCCI engine operation is compared over the EPA Heavy-Duty 13 mode supplemental emissions test with and without EGR. Emissions and efficiency metrics were examined over the entire engine map for both operating modes. It was found that the use of EGR lowered combustion noise to less than 97 dBa and lowered the cycle averaged NOx emissions by 48%, with only a slight increase in soot and 0.5 point decrease in brake thermal efficiency. Thus, operation with EGR offered the lowest total fluid consumption when considering the use of a selective catalytic reduction system for NOx aftertreatment.

Hanson, Reed↗

Performance, Efficiency and Emissions Assessment of Natural Gas Direct Injection compared to Gasoline and Natural Gas Port-Fuel Injection in an Automotive Engine

Interest in natural gas as a fuel for light-duty transportation has increased due to its domestic availability and lower cost relative to gasoline. Natural gas, comprised mainly of methane, has a higher knock resistance than gasoline making it advantageous for high load operation. However, the lower flame speeds of natural gas can cause ignitability issues at part-load operation leading to an increase in the initial flame development process. While port-fuel injection of natural gas can lead to a loss in power density due to the displacement of intake air, injecting natural gas directly into the cylinder can reduce such losses. A study was designed and performed to evaluate the potential of natural gas for use as a light-duty fuel. Steady-state baseline tests were performed on a single-cylinder research engine equipped for port-fuel injection of gasoline and natural gas, as well as centrally mounted direct injection of natural gas. Experimental results suggest that similar efficiencies can be achieved in part-load operation for both gasoline and natural gas. While the effects of injection timing are generally minimal for port-fuel injection, varying the injection timing for direct injection, especially after intake valve closure, can speed up the early flame development process by nearly 18°CA. Results at full-load suggest that operation with natural gas regardless of fuel system allows for an efficiency increase. While port-fuel injection of natural gas leads to a power density loss, direct injection of natural gas allows for up to a 10% improvement in full-load power density over liquid and gaseous port-fuel injection for a naturally aspirated engine. In addition to increasing full-load efficiencies, natural gas operation allows for up to a 30% reduction in engine out carbon dioxide emissions at full-load.

Sevik, James M↗

CFD and X-ray Analysis of Gaseous Direct Injection from an Outward Opening Injector

Using natural gas in an internal combustion engine (ICE) is emerging as a promising way to improve thermal efficiency and reduce exhaust emissions. In the development of such engine platforms, computational fluid dynamics (CFD) plays a fundamental role in the optimization of geometries and operating parameters. One of the most relevant issues in the simulation of direct injection (DI) gaseous processes is the accurate prediction of the gas jet evolution. The simulation of the injection process for a gaseous fuel does not require complex modeling, nevertheless properly describing high-pressure gas jets remains a challenging task. At the exit of the nozzle, the injected gas is under-expanded, the flow becomes supersonic and shocks occur due to compressibility effects. These phenomena lead to challenging computational requirements resulting from high grid resolution and low computational time-steps. In this paper, the simulation of gaseous injection from an outward opening injector was carried out with the commercial CFD software CONVERGE. Argon was injected into a quiescent chamber filled with Nitrogen. Two free-jet cases with injection pressure of 15 and 10 bar, and ambient pressure of 1 and 2 bar respectively, were tested. For the 15 bar injection pressure and 1 bar ambient pressure, a jet impinging on a barrier case was performed as well. The numerical results were validated against experimental mass measurements using X-ray radiography. The results, presented in terms of 2D maps and transverse sections of equivalent path length of argon, showed good agreement between modeling and experiments in terms of jet penetration, shape and gas mass distribution. These emphasized the significant impact of mesh size on the results for the simulation of this type of injector. Due to the small geometrical dimensions a fine mesh is required in order to deliver an accurate description of the mixture formation. Numerical results were discussed with a particular emphasis on the application to engine simulations, where a trade-off between accuracy and computational time is a necessity.

Bartolucci, Lorenzo↗

Engine Benchmarking - Final CRADA Report

Detailed benchmarking of the powertrains of three light-duty vehicles was performed. Results were presented and provided to CRADA partners. The vehicles included a MY2011 Audi A4, a MY2012 Mini Cooper and a MY2014 Nissan Versa.

33 ADVANCED PROPULSION SYSTEMS↗

Capturing Cyclic Variability in EGR Dilute SI Combustion using Multi-Cycle RANS

Dilute combustion is an effective approach to increase the thermal efficiency of spark-ignition (SI) internal combustion engines (ICEs). However, high dilution levels typically result in large cycle-to-cycle variations (CCV) and poor combustion stability, therefore limiting the efficiency improvement. In order to extend the dilution tolerance of SI engines, advanced ignition systems are the subject of extensive research. When simulating the effect of the ignition characteristics on CCV, providing a numerical result matching the measured average in-cylinder pressure trace does not deliver useful information regarding combustion stability. Typically Large Eddy Simulations (LES) are performed to simulate cyclic engine variations, since Reynold-Averaged Navier-Stokes (RANS) modeling is expected to deliver an ensemble-averaged result. In this paper it is shown that, when using RANS, the cyclic perturbations coming from different initial conditions at each cycle are not damped out even after many simulated cycles. As a result, multi-cycle RANS results feature cyclic variability. This allows evaluating the effect of advanced ignition sources on combustion stability but requires validation against the entire cycle-resolved experimental dataset. A single-cylinder GDI research engine is simulated using RANS and the numerical results for 20 consecutive engine cycles are evaluated for several operating conditions, including stoichiometric as well as EGR dilute operation. The effect of the ignition characteristics on CCV is also evaluated. Results show not only that multi-cycle RANS simulations can capture cyclic variability and deliver similar trends as the experimental data, but more importantly that RANS might be an effective, lower-cost alternative to LES for the evaluation of ignition strategies for combustion systems that operate close to the stability limit.

Scarcelli, Riccardo↗

EXTENDING LEAN AND EGR-DILUTE OPERATING LIMITS OF A MODERN GDI ENGINE USING A LOW-ENERGY TRANSIENT PLASMA IGNITION SYSTEM

The efficiency improvement and emissions reduction potential of lean and EGR dilute operation of spark-ignition gasoline engines is well understood and documented. However, dilute operation is generally limited by deteriorating combustion stability with increasing inert gas levels. The combustion stability decreases due to reduced mixture flame speeds resulting in significantly increased combustion initiation periods and burn durations. A study was designed and executed to evaluate the potential to extend lean and EGR-dilute limits using a low-energy transient plasma ignition system. The low-energy transient plasma was generated by nano-second pulses and its performance compared to a conventional transistorized coil ignition system operated on an automotive, gasoline direct injection (GDI) single-cylinder research engine. The experimental assessment was focused on steady-state experiments at the part load condition of 1500 rpm 5.6 bar IMEP, where dilution tolerance is particularly critical to improving efficiency and emissions performance. Experimental results suggest that the energy delivery process of the low-energy transient plasma ignition system significantly improves part load dilution tolerance by reducing the early flame development period. Statistical analysis of relevant combustion metrics was performed in order to further investigate the effects of the advanced ignition system on combustion stability. Results confirm that at select operating conditions EGR tolerance and lean limit could be improved by as much as 20% (from 22.7 to 27.1% EGR) and nearly 10% (from λ=1.55 to 1.7) with the low-energy transient plasma ignition system.

Sevik, James Michael↗

Impact of Effective Compression Ratio on Gasoline-Diesel Dual-Fuel Combustion in a Heavy-Duty Engine Using Variable Valve Actuation

Dual-fuel combustion using port-injected gasoline with a direct diesel injection has been shown to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions, and high indicated thermal efficiency. A key requirement for extending high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. Reducing compression ratio, in conjunction with a higher expansion ratio using alternative valve timings, decreases compressed charge reactivity while maintain a high expansion ratio for maximum work extraction. Experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate dual-fuel combustion with port gasoline injection to supplement the direct diesel injection. The engine employs intake variable valve actuation (VVA) for early (EIVC) or late (LIVC) intake valve closing to yield reduced effective compression ratio. Testing was conducted at a mid-load operating condition using a gasoline-diesel dual-fuel operating strategy. The impact on dual-fuel engine performance and emissions with respect to varying effective compression ratio is quantified within this study. As effective compression ratio is reduced, overall massflow through the engine decreases, yielding both higher gas exchange efficiencies and increased heat transfer losses. With constant combustion phasing gasoline/diesel fueling fraction, and NOx emissions held constant, overall brake thermal efficiency remains relatively constant across effective compression ratios.

Ickes, Andrew↗

Effects of Ignition and Injection Perturbation under Lean and Dilute GDI Engine Operation

Turbocharged gasoline direct injection (GDI) engines are quickly becoming more prominent in light-duty automotive applications because of their potential improvements in efficiency and fuel economy. While EGR dilute and lean operation serve as potential pathways to further improve efficiencies and emissions in GDI engines, they also pose challenges for stable engine operation. Tests were performed on a single-cylinder research engine that is representative of current automotive-style GDI engines. Baseline cases were performed under steady-state operating conditions where combustion phasing and dilution were varied to determine the effects on indicated efficiency and combustion stability. Sensitivity studies were then carried out by introducing binary low-high perturbation of spark timing and injection duration on a cycle-by-cycle basis under EGR dilute and lean operation to determine dominant feedback mechanisms. Ignition perturbation was phased early/late of MBT timing, and injection perturbation was set fuel rich/lean of the given air-fuel ratio. COVIMEP was used to define acceptable operation limits when comparing different perturbation cases. Overall results suggests that combustion phasing is very important for dilute operation while the impact of perturbation is reduced due to increased burn duration compared to the stoichiometric baseline without EGR. Lean operation was found to be very sensitive to injection perturbation, with the effect of perturbations amplified by next-cycle feedback. Due to the longer timescale EGR operation was shown to be less sensitive to next-cycle changes in fueling.

Wallner, Thomas↗

Experimental investigation of a DISI production engine fuelled with methanol, ethanol, butanol, and iso-stoichiometric alcohol blends

Stricter CO2 and emissions regulations are pushing spark ignition engines more and more towards downsizing, enabled through direct injection and turbocharging. The advantages which come with direct injection, such as increased charge density and an elevated knock resistance, are even more pronounced when using low carbon number alcohols instead of gasoline. This is mainly due to the higher heat of vaporization and the lower air-to-fuel ratio of light alcohols such as methanol, ethanol and butanol. These alcohols are also attractive alternatives to gasoline because they can be produced from renewable resources. Because they are liquid, they can be easily stored in a vehicle. In this respect, the performance and engine-out emissions (NOx, CO, HC and PM) of methanol, ethanol and butanol were examined on a 4 cylinder 2.4 DI production engine and are compared with those on neat gasoline. Additionally, measurements were done for E85 and a methanol-gasoline blend with the same air-to-fuel ratio as E85 because this ‘iso-stoichiometric’ methanol-gasoline blend shows very few differences in physical properties to E85 and has the potential to be used as ‘drop-in’ fuel for flex-fuel vehicles. It is shown that the brake thermal efficiency when running on alcohol fuels is significantly better than with gasoline while emitting fewer emissions. In a knock limited case for gasoline, the brake thermal efficiency on methanol was more than 5 percentage points better than on gasoline. The engine test results also confirm that, from an engine control point of view, the ‘iso-stoichiometric’ methanol-gasoline blend can indeed be used as a ‘drop-in’ fuel for E85.

Sileghem, Louis↗

In-Cylinder Oxygen Mass Fraction Estimation Method for Minimizing Cylinder-to-Cylinder Variations

Recent developments in advanced combustion engines have demonstrated the potential increases in efficiency and reductions in emissions through low temperature combustion (LTC). These combustion modes often rely on high exhaust gas recirculation (EGR), early fuel injection systems, and in some cases a combination of fuels with different reactivities. Despite the advantages of LTC, such operations are highly sensitive to the in-cylinder pre-combustion conditions and face significant challenges in multi-cylinder operation due to cylinder-to-cylinder variations of the combustion process. The cause of cylinder-to-cylinder variations is strongly tied to non-uniform trapped mass. In particular, in-cylinder oxygen concentration plays a critical role in the combustion process of each cylinder and can be leveraged to predict combustion characteristics and to develop control algorithms that mitigate cylinder-to-cylinder variation. This paper discusses a control-oriented model for estimating the in-cylinder oxygen mass fraction of each individual cylinder. The method relies on an Arrhenius correlation that establishes a relation between oxygen mass fraction, ignition delay, fuel activation energy, and in-cylinder average temperature and pressure during the ignition delay period. The scope of this study is the investigation of this relation on a single injection diesel fuel combustion in a multi-cylinder engine where the main characteristics of LTC operation, early fuel injection and high EGR, are realized. The model developed in this work accurately estimates the oxygen mass fraction of an individual cylinder in the 20 operating conditions studied with a standard deviation of 0.47% O2.

Kassa, Mateos↗

Air-to-Fuel Ratio Calculation Methods for Oxygenated Fuels in Two-Stroke Engines

In 1990, Roy Douglas developed an analytical method to calculate the global air-to-fuel ratio of a two-stroke engine from exhaust gas emissions. While this method has considerable application to two-stroke engines, it does not permit the calculation of air-to-fuel ratios for oxygenated fuels. This study proposed modifications to the Roy Douglas method such that it can be applied to oxygenated fuels. The ISO #16183 standard, the modified Spindt method, and the Brettschneider method were used to evaluate the modifications to the Roy Douglas method. In addition, a trapped air-to-fuel ratio, appropriate for two-stroke engines, was also modified to incorporate oxygenated fuels. To validate the modified calculation method, tests were performed using a two-stroke carbureted and two-stroke direct injected marine outboard engine over a five-mode marine test cycle running indolene and low level blends of ethanol and iso-butanol fuels. Results indicate that the modified air-fuel ratio method closely relates to the ISO #16183 standard. The modified Spindt method over-estimated the global air-to-fuel ratio. While the Brettschneider is considered an advancement over the Spindt method, it still provided an over-estimate of the air-to-fuel ratio. Applying a trapped air-to-fuel ratio calculation to the modified Roy Douglas method provided a calculation for trapped air-to-fuel ratio for two-stroke engine operation, which correlated with engine-out CO emissions. The trapped air-to-fuel ratio calculation also provided improvements in air-to-fuel ratio predictions, especially during idle conditions.

Sevik, James Michael↗

Effects of Ignition and Injection Perturbation under Lean and Dilute GDI Engine Operation

Turbocharged gasoline direct injection (GDI) engines are quickly becoming more prominent in light-duty automotive applications because of their potential improvements in efficiency and fuel economy. While EGR dilute and lean operation serve as potential pathways to further improve efficiencies and emissions in GDI engines, they also pose challenges for stable engine operation. Tests were performed on a single-cylinder research engine that is representative of current automotive-style GDI engines. Baseline cases were performed under steady-state operating conditions where combustion phasing and dilution levels were varied to determine the effects on indicated efficiency and combustion stability. Sensitivity studies were then carried out by introducing binary low-high perturbation of spark timing and injection duration on a cycle-by-cycle basis under EGR dilute and lean operation to determine dominant feedback mechanisms. Ignition perturbation was phased early/late of MBT timing, and injection perturbation was set fuel rich/lean of the given air-to-fuel ratio. COVIMEP was used to define acceptable operation limits when comparing different perturbation cases. Overall sensitivity data shows COVIMEP is more sensitive to injection perturbation over ignition perturbation. This is because of the greater effect injection perturbation has on combustion phasing, ignition delay, and combustion duration.

Wallner, Thomas↗