Search NASA⌕ Search

Engineering topics

Walsh, M. J.

Publications and source records attributed to Walsh, M. J..

At least 19 records

Progress in ITER ECE diagnostic design and integration

The ITER electron cyclotron emission (ECE) diagnostic system has primary roles in providing measurements of the core electron temperature profile and the electron temperature fluctuation associated with the neoclassical tearing modes. The ITER ECE system includes a radial and oblique line-of-sight. Four 43-meter long low-loss transmission lines (TLs) are designed to transmit millimeter wave power in the frequency range of 70–1000 GHz in both X- and O-mode polarization from the port plug to the ECE instrumentation room in the diagnostic building. The measurement instrumentation includes two Fourier transform spectrometer (FTS) systems and two radiometer systems. The Indian Domestic Agency (IN-DA) and United States Domestic Agency share the responsibility. The IN-DA scope excluding instrumentation and control has passed its preliminary design review and is progressing towards the final design review (FDR). In parallel, the diagnostic integration in different areas is ongoing. Furthermore, several captive components for the TLs have passed FDR and will be manufactured for installation in the tokamak building soon. A peer review meeting has been held on the prototype hot calibration source, and its integration and new thermal analysis in the diagnostic shield module are continuing. A prototype TL is being tested. A prototype polarizing Martin-Puplett type FTS, operating in the frequency range 70–1000 GHz, features an in-vacuo fast scanning mechanism and a cryo-cooled dual-channel THz detector system. Its performance has been assessed in detail against ITER requirements.

47 OTHER INSTRUMENTATION↗

Engineering aspects of design and integration of ECE diagnostic in ITER

ITER ECE diagnostic [1] needs not only to meet measurement requirements, but also to withstand various loads, such as electromagnetic, mechanical, neutronic and thermal, and to be protected from stray ECH radiation at 170 GHz and other millimeter wave emission, like Collective Thomson scattering which is planned to operate at 60 GHz. Same or similar loads will be applied to other millimetre-wave diagnostics [2], located both in-vessel and in-port plugs. These loads must be taken into account throughout the design phases of the ECE and other microwave diagnostics to ensure their structural integrity and maintainability. The integration of microwave diagnostics with other ITER systems is another challenging activity which is currently ongoing through port integration and in-vessel integration work. Port Integration has to address the maintenance and the safety aspects of diagnostics, too. Engineering solutions which are being developed to support and to operate ITER ECE diagnostic, whilst complying with safety and maintenance requirements, are discussed in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Edge Thomson scattering diagnostic on COMPASS tokamak: Installation, calibration, operation, improvements

The core Thomson scattering diagnostic (TS) on the COMPASS tokamak was put in operation and reported earlier. Implementation of edge TS, with spatial resolution along the laser beam up to ∼1/100 of the tokamak minor radius, is presented now. The procedure for spatial calibration and alignment of both core and edge systems is described. Several further upgrades of the TS system, like a triggering unit and piezo motor driven vacuum window shutter, are introduced as well. The edge TS system, together with the core TS, is now in routine operation and provides electron temperature and density profiles.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-resolution Thomson scattering system on the COMPASS tokamak: Evaluation of plasma parameters and error analysis

The electron density and temperature profiles measured by the Thomson scattering diagnostic on the COMPASS tokamak are used for estimation of electron kinetic energy, energy confinement time, and effective charge number Z{sub eff}. Data are compared with the line-integrated electron density measured by a microwave interferometer in an ohmically heated plasma with a circular cross section. An error analysis of both electron temperature and density are performed by two methods-a constant chi-square boundaries method and a Monte Carlo simulation, determining asymmetrical error bars for the electron temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Combined Devices for Turbulent-Drag Reduction

Aircraft skin-friction drag reduced as much as 15 percent. One effective drag-reduction technique involves use of riblets. Riblets are longitudinal striations or grooves machined on originally smooth surface. Grooves alined with flow. Grooves have depths and spacings on order of turbulent wallstreak and burst dimensions and designed to change near-wall structure of turbulent boundary layer. Another approach, using large-eddy-breakup (LEBU) devices, or turbulence manipulators or ribbons also demonstrated reductions in local skin friction and net drag in air. LEBU device consists of thin, ribbonlike strips or airfoils suspended parallel to test surface and positioned within turbulent boundary layer. Technique potentially reduce net skin-friction drag by at least 15 percent on turbulent boundary layer of aircraft, representing possible annual savings in fuel costs of $300 to $400 million for U.S. commercial fleet. Also applicable to frictionloss reduction inside pipes and ducts, contributing to increased efficiency of pumps, heat exchangers, air conditioners, and other devices involving fluid flow.

Walsh, M. J.↗

Turbulent roughness drag due to surface waviness at low roughness Reynolds numbers

The current investigation has the objective to provide data which will make it possible to obtain a better estimate regarding the roughness drag for surface waviness. The data employed for this investigation were acquired in connection with a wavy wall study which was conducted as part of an overall program to reduce the skin friction of turbulent boundary layers in external flows. The results of the present investigation show that the low-speed roughness drag of small-amplitude sinusoidal wave trains having wavelengths of the order of the boundary-layer thickness is not only a function of h/lambda (h = total wave height, lambda = wavelength), but, in addition, is also a function of the roughness Reynolds number.

Lin, J. C.↗

Turbulent drag reduction research

Research in the area of turbulent drag reduction for attached flows is summarized. The most promising passive techniques utilize non-planar geometry. Of particular interest is the suitability of these devices for retrofit of existing vehicles. Five methods for reducing turbulent skin friction drag on bodies/fuselages are discussed. They are: (1) large-eddy breakup devices; (2) riblets; (3) slot injection optimization; (4) control of Emmons spot generation; and (5) relaminarization through massive suction. Except for the Emmons spot work these methods all indicate the possibility of sizable net reductions in skin friction for laboratory conditions.

Bushnell, D. M.↗

Drag of two-dimensional small-amplitude symmetric and asymmetric wavy walls in turbulent boundary layers

Included are results of an experimental investigation of low-speed turbulent flow over multiple two-dimensional transverse rigid wavy surfaces having a wavelength on the order of the boundary-layer thickness. Data include surface pressure and total drag measurements on symmetric and asymmetric wall waves under a low-speed turbulent boundary-layer flow. Several asymmetric wave configurations exhibited drag levels below the equivalent symmetric (sine) wave. The experimental results compare favorably with numerical predictions from a Reynolds-averaged Navier-Stokes spectral code. The reported results are of particular interest for the estimation of drag, the minimization of fabrication waviness effects, and the study of wind-wave interactions.

Lin, J. C.↗

Optimization and application of riblets for turbulent drag reduction

Riblet surfaces have been tested in boundary layers having different upstream histories and at higher Reynolds numbers than previously reported. The drag reduction for the riblet surfaces was found to be dependent on the height and spacing of the riblets in law-of-the-wall variables regardless of the free-stream Reynolds number or upstream boundary-layer history. Micro-photographs of the actual riblet geometries are examined to determine the effect of rib details on the riblet drag-reduction performances. To further increase drag-reduction performance, riblet surfaces are combined with another drag-reduction concept, the large-eddy breakup device (LEBU). In addition, the yaw sensitivity of riblets is evaluated, as well as the characteristics of riblet surfaces manufactured out of a thin vinyl sheet.

Walsh, M. J.↗

Axisymmetric bluff-body drag reduction using circumferential grooves

The effect of shoulder radiusing and circumferentially grooving the afterbodies of bluff bodies to reduce the base drag at low speeds is discussed. Shoulder radii as large as 2.75 body diameters are examined. Reynolds number based on body diameter varied from 20,000 to 200,000. Results indicate that increasing the shoulder radius to 2.75 body diameters can reduce the drag levels to those of a streamline body having 67 percent greater fineness ratio. For zero shoulder radius, circumferential grooves were found to be effective in reducing body drag for zero shoulder radius in both laminar and tripped flow. Circumferential grooves on the afterbody with a shoulder radius of one-half the body diameter were only effective in reducing drag for laminar flow.

Howard, F. G.↗

Research on non-planar wall geometries for turbulence control and skin-friction reduction

Eight turbulence-control/drag-reduction concepts under study at NASA Langley Research Center are discussed. These concepts include: slot injection, ion wind, large-eddy breakup devices, riblets, relaminarization, convex curvature, passive porous walls, and rigid wavy walls. Of these concepts, passive porous walls and small wavelength wavy walls are found to increase drag. Riblets, slot injection, and large-eddy breakup devices reduce net turbulent drag, at least for some conditions. The ion wind, relaminarization, and convex curvature studies are still in the early stages and require further work to evaluate their applicability for drag reduction.

Hefner, J. N.↗

Turbulent drag characteristic of small amplitude rigid surface waves

The paper discusses an experimental and theoretical investigation of low speed turbulent flow over transverse rigid wavy surfaces having a wavelength on the order of the boundary layer thickness. In addition the results of theoretical investigations of laminar flow over short wavelength waves and turbulent flow over long wavelength (wavelength much greater than the boundary layer thickness) wavy walls are presented. Surface pressure and net drag measurements obtained for the short wavelength symmetric and asymmetric waves in a turbulent flow agreed with the results obtained with a Navier-Stokes spectral code and indicated no significant drag reduction. Several asymmetric wave configurations did significantly reduce the pressure drag compared to sine wave geometries, but these waves still did not produce a net drag reduction. The Navier-Stokes calculations for laminar flow indicated a drag reduction of up to 17 percent for certain short wavelength waves. Boundary layer calculations for turbulent flow over long wavelength surface waves indicated that net drag reductions on the order of 10 percent may be possible for large-radius waisted bodies.

Lin, J. C.↗

Toward autonomous spacecraft

Ways in which autonomous behavior of spacecraft can be extended to treat situations wherein a closed loop control by a human may not be appropriate or even possible are explored. Predictive models that minimize mean least squared error and arbitrary cost functions are discussed. A methodology for extracting cyclic components for an arbitrary environment with respect to usual and arbitrary criteria is developed. An approach to prediction and control based on evolutionary programming is outlined. A computer program capable of predicting time series is presented. A design of a control system for a robotic dense with partially unknown physical properties is presented.

Fogel, L. J.↗

Turbulent boundary layer drag reduction using riblets

An experimental study of low-speed turbulent boundary layer flow over longitudinally grooved surfaces (i.e., riblets) is discussed. Results obtained with a highly accurate drag balance indicate that v-groove riblet surfaces can produce consistent net drag reductions as large as 8 percent provided the height and spacing of the grooves in terms of law of the wall variables are less than 25 wall units. Momentum balances confirmed these direct drag measurements. Conditionally sampled data indicate that the burst frequency for riblets is approximately the same as that for a flat plate but turbulence intensity is reduced. Attempts to optimize the net drag reduction by varying riblet cross-sectional geometry and alignment are also discussed.

Walsh, M. J.↗

Grooves reduce aircraft drag

Aerodynamic drag can be reduced by many small longitudinal grooves machined in aircraft skin. Experiments show that grooves parallel to airflow reduce drag by 4 to 7 percent. Reduced drag translates into reduced engine power required to overcome drag and ultimately to lower fuel consumption.

Walsh, M. J.↗

Drag characteristics of V-groove and transverse curvature riblets

The paper examines the drag characteristics of longitudinally ribbed surfaces where the rib dimensions are the order of the initial turbulent wall burst region near the wall. Direct drag measurements are presented for symmetric and unsymmetric V-groove, and (larger wavelength) transverse curvature riblets. The direct drag data indicate net drag reductions as large as 7% for certain V-groove riblets with heights in terms of law of the wall coordinates h+ less than 30. For one of the riblet models, the drag reduction is confirmed by reductions in the momentum thickness, turbulent velocity fluctuations, and Reynolds stress profiles. Although the direct drag data for the transverse curvature riblets showed drag increases, certain models did show that the drag increase diminished with increasing velocity. This trend is opposite to the normal one found for rough surfaces and should be investigated further.

Walsh, M. J.↗

Criteria for asymptotic supersonic two-dimensional turbulent wakes

Indicators used to determine the fully developed mean flow for two dimensional turbulent supersonic wakes are examined. The similarity variables for velocity temperature and the transverse coordinate used by Demetriades (1969) and Wagner (1972) are shown not to adequately distinguish transition from developed turbulent flows. The growth rate of the two dimensional turbulent wake as the wake develops from laminar to turbulent are shown to be low in the laminar region, increase at transition, and level off as fully developed turbulence is attained, demonstrating that wake growth rates are better indicators of a fully developed mean flow than are similarity variables.

Walsh, M. J.↗