Search NASA⌕ Search

Engineering topics

Waluyo, Iradwikanari

Publications and source records attributed to Waluyo, Iradwikanari.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Understanding improved cycling and thermal stability of compositionally graded Ni-rich layered LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode materials

The concentration gradient is a strategic design, adjusting the distribution of Ni, typically with a higher Ni content in the core and a higher Mn content toward the surface. This design leverages the pivotal role of the Ni/Mn ratio, seeking to optimize cathode performance by balancing Ni's high capacity with Mn's stabilizing effects, particularly at the surface where degradation commonly occurs during cycling. Here, our study delves into the intricate structural and chemical transformations within concentration gradient cathode materials during electrochemical cycling. Utilizing advanced synchrotron X-ray techniques, including hard and soft X-ray absorption spectroscopy (hXAS, sXAS), and nanoscale X-ray imaging, we investigate buried changes in concentration gradient LiNi 0.6 Mn 0.2 Co 0.2 O 2 (CG NMC622). Contrary to conventional assumptions, our findings challenge the notion that cycling stability relies solely on Mn stability. Unraveling the roles of Ni and Mn, we uncover how their individual and collective contributions impact the cathode's overall performance. This investigation transcends established paradigms, shedding light on the crucial mechanisms governing the enhanced cycling stability of Nirich layered cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2024

MgO Nanostructures on Cu(111): Understanding Size- and Morphology-Dependent CO 2 Binding and Hydrogenation

To design and optimize cost-effective technologies for the capture, utilization, and storage of carbon dioxide (CO 2 ), we need a fundamental knowledge and control of chemical interactions associated with the capture and conversion of the molecule into high-value chemicals, minerals, and all kinds of materials. Bulk magnesium oxide (MgO) is frequently used for the trapping and storage of CO 2 by generation of magnesium carbonates. In this study, the growth and reactivity of MgO nanostructures on a Cu 2 O/Cu(111) substrate were investigated using scanning tunneling microscopy (STM) and synchrotron-based ambient-pressure X-ray photoelectron spectroscopy (AP-XPS). For extremely small concentrations of Mg (~ 0.01 monolayer (ML)), a well-ordered film of copper oxide with small clusters (0.2-0.5 nm in width, 0.4-0.6 Å in height) of embedded MgO was seen. At a coverage of 0.1 ML, MgO nanoparticles with a width of 0.4 to 1 nm and a height of ~ 1.5 Å were randomly distributed on the copper oxide. Further, random distribution was also observed when the MgO coverage was raised to 0.25 ML, with the width of the MgO particles increasing to 2-2.5 nm and the height reaching 2 Å. These oxide nanostructures displayed a high reactivity towards CO 2 and H 2 that is not seen for bulk MgO. Dissociation of H 2 was observed at room temperature with reaction of the H adatoms with CuO x and C-containing groups. On the small MgO nanostructures (< 1 nm in width), instead of plain carbonate formation, there was dissociation of CO 2 into CO and C species, opening reaction channels for the conversion of this harmful molecule into oxygenates and light alkanes.

03 NATURAL GAS↗
DOE OSTI2024

Tuning Strong Metal–Support Interactions via Synergistic Alloying

The encapsulation phenomenon associated with strong metal-support interaction (SMSI) has been largely restricted to catalyst systems consisting of group VIII metals with high surface energy and reducible transition metal oxide supports with low surface energy. Here, we demonstrate an encapsulation phenomenon that, while sharing morphological similarities with conventional SMSI, follows a distinctive pathway. This is shown by the encapsulation of CuAu nanoparticles (NPs) supported on highly ordered pyrolytic graphite (HOPG). Through dynamic monitoring of Cu, Au, and Cu 50 Au 50 NPs in an oxidizing atmosphere using ambient-pressure X-ray photoelectron spectroscopy, we show that this spontaneous encapsulation is achieved through the synergistic effect of the alloying elements. Specifically, the surface segregation of Cu promotes dissociative O 2 adsorption, leading to the formation of atomic O species, while the subsurface enrichment of Au hinders O incorporation into the bulk of CuAu NPs. Consequently, O spillover onto the graphite support occurs, resulting in the oxidation of the HOPG surface into graphitic oxide species. The higher affinity of the graphitic oxide species toward the Cu-segregated surface prompts their migration from the HOPG support to encapsulate the CuAu NPs. Finally, these results transcend the conventional SMSI and bear practical implications for the design and development of heterogeneous catalysts, particularly in carbon-supported alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Morphology Dependent Reactivity of CsO $x$ Nanostructures on Au(111): Binding and Hydrogenation of CO 2 to HCOOH

Cesium oxide (CsO $x$ ) nanostructures grown on Au(111) behave as active centers for CO 2 binding and hydrogenation reactions. The morphology and reactivity of these CsO $x$ systems were investigated as a function of alkali coverage using scanning tunnelling microscopy (STM), ambient pressure X-ray photoelectron spectroscopy (AP-XPS), and density functional theory (DFT) calculations. STM results show that initially (0.05 - 0.10 ML) cesium oxide clusters (Cs 2 O 2 ) grow at the elbow sites of the herringbone of Au(111), subsequently transforming into two-dimensional islands with increasing cesium coverage (> 0.15 ML). XPS measurements reveal the presence of suboxidic (Cs $y$ O; $y$ ≥ 2) species for the island structures. The higher coverages of cesium oxide nanostructures contain a lower O/Cs ratio resulting in a stronger binding of CO 2 . Moreover, the O atoms in the Cs $y$ O structure undergo a rearrangement upon the adsorption of CO 2 which is a reversible phenomenon. Under CO 2 hydrogenation conditions, the small Cs 2 O 2 clusters are hydroxylated, thereby preventing the adsorption of CO 2 . However, the hydroxylation of the higher coverages of Cs $y$ O did not prevent CO 2 adsorption, and the adsorbed CO 2 transformed to HCOO species that eventually yield HCOOH. DFT calculations further confirm that the dissociated H 2 attacks the C in the adsorbate to produce formate, which is both thermodynamically and kinetically favored during the CO 2 reaction with hydroxylated Cs $y$ O. These results demonstrate that cesium oxide by itself is an excellent catalyst for CO 2 hydrogenation that could produce formate, an important intermediate for the generation of value-added species. The role of the alkali oxide nanostructures as active centers, not merely as promoters, may have broad implications wherein the alkali oxides can be considered in the design of materials tuned for specific applications in heterogeneous catalysis.

03 NATURAL GAS↗
DOE OSTI2023

Oxidation of NiCr and NiCrMo Alloys at Low Temperatures

Oxidation of Ni-Cr and Ni-Cr-Mo was studied in operando with near ambient pressure x-ray photoelectron spectroscopy in the Cabrera-Mott regime. The oxidation temperature was 200 °C - a severely diffusion limited regime. The near-surface alloy is Cr-enriched after reduction of natives oxide in vacuum, and especially so for Ni-15Cr-6Mo. Mo-cations are integrated in the oxide and Mo(VI) dominates at the surface. The surface chemistry driven promotion of chromia by Mo predicted by theory is negated by the limited surface diffusion of reactants. Furthermore, pre-oxidation processing is proposed to control the oxide properties for use of Ni-Cr superalloys at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microscopic Investigation of H 2 Reduced CuO x /Cu(111) and ZnO/CuO x /Cu(111) Inverse Catalysts: STM, AP-XPS, and DFT Studies

Understanding the reduction mechanism of ZnO/CuO x interfaces by hydrogen is of great importance for advancing the performance of industrial catalysts for CO 2 hydrogenation to methanol. Here, the reduction of pristine and ZnO-modified CuO x /Cu(111) by H 2 was investigated using ambient pressure scanning tunnelling microscopy (AP-STM), ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and density functional theory (DFT). The morphological changes and reaction rates seen for the reduction of CuO x /Cu(111) and ZnO/CuO x /Cu(111) are very different. On CuO x /Cu(111), perfect "44" and "29" structures displayed a very low reactivity towards H 2 at room temperature. A long induction period associated with an autocatalytic process was observed to enable the reduction by the removal of chemisorbed non-lattice oxygen initially and lattice oxygen sequentially at the CuO x -Cu interface, which led to formation of oxygen deficient "5-7" hex and honeycomb structures. In the final stages of the reduction process, regions of residual oxygen species and metallic Cu were seen. The addition of ZnO particles to CuO x /Cu(111) opened new reaction channels. On the ZnO sites, the dissociation of H 2 was fast and H adatoms easily migrated to adjacent regions of copper oxide. This hydrogen spillover substantially enhanced the rate of oxygen removal, resulting in the rapid reduction of the copper oxide located in the periphery of the zinc oxide islands with no signs for the reduction of ZnO. The deposited ZnO completely modified the dynamics for H 2 dissociation and hydrogen migration, providing an excellent source for CO 2 hydrogenation processes on the inverse oxide/metal system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Effect of Surface Temperature on the Distribution and Reactivity of Rh Active Sites for CO Oxidation

Single–atom catalysts are a fast–emerging area in which late–transition metal atoms are supported on oxides, metals, and carbonaceous supports. They show great promise for selective chemical reactions due to their well–defined active sites, and significantly reduce precious metal loading. However, oxide–supported single–atom catalysts have drawbacks such as deactivation due to sintering, and there are on–going debates about the exact nature of the active sites. Herein we report a model system where the surface temperature during Rh deposition on a copper oxide support dictates the Rh size distribution. Here our temperature–programmed desorption experiments reveal that Rh clusters perform CO oxidation at lower temperature than single atoms, and isotopic labelling demonstrates differences in the mechanism in that the C–O bond is broken and reformed on clusters, as opposed to a pure Mars van Krevelen mechanism for CO oxidation at the single–atom Rh sites. We further examine the cluster size distributions with scanning tunneling microscopy and X–ray photoelectron spectroscopy which confirm the presence of both clusters and single atoms for the lower temperature deposition and only single atoms for the higher temperature deposition. Together, these results provide a fundamental understanding of the differences in the CO oxidation mechanism on Rh atoms and clusters.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Chemical Profiles of the Oxides on Tantalum in State of the Art Superconducting Circuits

Abstract Over the past decades, superconducting qubits have emerged as one of the leading hardware platforms for realizing a quantum processor. Consequently, researchers have made significant effort to understand the loss channels that limit the coherence times of superconducting qubits. A major source of loss has been attributed to two level systems that are present at the material interfaces. It is recently shown that replacing the metal in the capacitor of a transmon with tantalum yields record relaxation and coherence times for superconducting qubits, motivating a detailed study of the tantalum surface. In this work, the chemical profile of the surface of tantalum films grown on c‐plane sapphire using variable energy X‐ray photoelectron spectroscopy (VEXPS) is studied. The different oxidation states of tantalum that are present in the native oxide resulting from exposure to air are identified, and their distribution through the depth of the film is measured. Furthermore, it is shown how the volume and depth distribution of these tantalum oxidation states can be altered by various chemical treatments. Correlating these measurements with detailed measurements of quantum devices may elucidate the underlying microscopic sources of loss.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structural and Interphasial Stabilities of Sulfurized Polyacrylonitrile (SPAN) Cathode

Sulfurized polyacrylonitrile (SPAN) has attracted a lot of attention because of its low cost, high capacity, and great reversibility. Due to its structural complexity and amorphous nature, reaction mechanism of SPAN is little understood. Here, for this paper, we study the structural and interphasial changes of SPAN using synchrotron-based pair distribution function (PDF) analysis and soft X-ray absorption spectroscopy (sXAS). PDF identifies key structural features, including C–S bond, sulfur dimer, and sulfur chain in SPAN. The sulfur dimer bridging the pyridine network partially converts to sulfur chain during the first charging. In the following cycles, sulfur chain goes through lithiation and delithiation with reversibility dependent on the electrolytes. SXAS reveals surface changes of SPAN. After the first cycle, a negatively charged carbon or fused benzene layer is formed, on top of which is another layer formed by the electrolyte decomposition. The layer formed by localized high concentration electrolyte is stable during cycling.

25 ENERGY STORAGE↗
DOE OSTI2023

Assessing factors that determine adatom migration and clustering on a thin film oxide; Pt 1 and Rh 1 on the “29” Cu x O/Cu(1 1 1) surface

The dynamical nature of single-site catalysts under non-equilibrium conditions poses significant challenges in the full characterization of their active sites. The “29” oxide is a thin Cu x O film grown on Cu(111) which provides a well-defined surface on which to study the structure and chemistry of atomically dispersed precious metals. A combination of experimental and first-principles approaches is used to investigate the factors that influence the mobility of metal adatoms and their clustering tendencies. Our work elucidates how a homogenous coordination environment of neutral single-atoms can be obtained when its tendency to break oxide bonds within its vicinity is low. Herein we demonstrate that this in turn affects the chemical atomically dispersed species on thin-film oxides, as defects on the oxide would in fact allow such species to be more accessible to CO. We thus highlight the importance of understanding the relationship between defects and atomically dispersed active sites upon designing single-site catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Atomic Structural Origin of the High Methanol Selectivity over In 2 O 3 –Metal Interfaces: Metal–Support Interactions and the Formation of a InO x Overlayer in Ru/In 2 O 3 Catalysts during CO 2 Hydrogenation

CO 2 hydrogenation to methanol is of great environmental and economic interest due to its potential to reduce carbon emissions and produce valuable chemicals in one single reaction. Compared with the unmodified traditional Cu/ZnO/Al 2 O 3 catalyst, an indium oxide (In 2 O 3 )-based catalyst can double the methanol selectivity from 30–50 to 60–100%. It is worth noting that over catalysts involving various active metals dispersed on indium oxide (M/In 2 O 3 , M = Pd, Ni, Au, etc.), although the methanol yield is boosted, the selectivity remains similar to that of plain In 2 O 3 despite the distinct chemical properties of the added metals. Here, to investigate the phenomena behind this behavior, we used RuO 2 /In 2 O 3 as a test catalyst. The results of ambient pressure photoelectron spectroscopy, in situ X-ray absorption fine structure, and time-resolved X-ray diffraction indicate that the structure of the RuO 2 /In 2 O 3 catalyst is highly dynamic in the presence of a reactive environment. Specifically, under CO 2 hydrogenation conditions, Ru clusters facilitate the reduction of In 2 O 3 to generate In 2 O 3–x aggregates, which encapsulate the Ru systems in a migration driven by thermodynamics. In this way, the Ru O sites for CH 4 production are blocked while creating RuO x –In 2 O 3–x interfacial sites with tunable metal–oxide interactions for selective methanol production. In an inverse oxide/metal configuration, indium oxide has properties not seen in its bulk phase that are useful for the binding and conversion of CO 2 . This work reveals the dynamic nature of In 2 O 3 -based catalysts, providing insights for a rational design of materials for the selective synthesis of methanol.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fast Surface Oxygen Release Kinetics Accelerate Nanoparticle Exsolution in Perovskite Oxides

Exsolution is a recent advancement for fabricating oxide-supported metal nanoparticle catalysts via phase precipitation out of a host oxide. A fundamental understanding and control of the exsolution kinetics are needed to engineer exsolved nanoparticles to obtain higher catalytic activity toward clean energy and fuel conversion. Since oxygen release via oxygen vacancy formation in the host oxide is behind oxide reduction and metal exsolution, we hypothesize that the kinetics of metal exsolution should depend on the kinetics of oxygen release, in addition to the kinetics of metal cation diffusion. In this report we probe the surface exsolution kinetics both experimentally and theoretically using thin-film perovskite SrTi 0.65 Fe 0.35 O 3 (STF) as a model system. We quantitatively demonstrated that in this system the surface oxygen release governs the metal nanoparticle exsolution kinetics. As a result, by increasing the oxygen release rate in STF, either by reducing the sample thickness or by increasing the surface reactivity, one can effectively accelerate the Fe 0 exsolution kinetics. Fast oxygen release kinetics in STF not only shortened the prereduction time prior to the exsolution onset, but also increased the total quantity of exsolved Fe 0 over time, which agrees well with the predictions from our analytical kinetic modeling. The consistency between the results obtained from in situ experiments and analytical modeling provides a predictive capability for tailoring exsolution, and highlights the importance of engineering host oxide surface oxygen release kinetics in designing exsolved nanocatalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conversion of CO 2 to Methanol and Ethanol on Pt/CeO x /TiO 2 (110): Enabling Role of Water in C–C Bond Formation

The surface chemistry of alcohol synthesis from CO 2 hydrogenation has been investigated using kinetic testing, ambient pressure x-ray photoelectron spectroscopy (AP-XPS) and DFT calculations over a multicomponent system where Pt and ceria nanoparticles coexisted on a titania template, Pt/CeO x /TiO 2 (110). Due to its high ability to bind and activate CO 2 , not seen for typical Cu-ZnO catalysts, the Pt-CeO x -TiO 2 interface is excellent for the hydrogenation of CO 2 to methanol with some ethanol also being produced (21% selectivity). The results of AP-XPS and DFT calculations indicate that the active state involves a mixture of Ti 4+ /Ti 3+ , Ce 3+ and Pt 0 /Pt + . A fast pathway for the formation of CH 3 O species is only plausible when Ce 3+ and Pt are present. The addition of water to the reaction feed facilitates the first hydrogenation of CO 2 and substantially enhances the surface coverage of C-containing species (CH 3 O, HCOO, CO 3 , CH x ), facilitating the formation of C-C bonds and the production of ethanol (38% selectivity).

36 MATERIALS SCIENCE↗
DOE OSTI2022

The Interaction of K and O 2 on Au(111): Multiple Growth Modes of Potassium Oxide and Their Catalytic Activity for CO Oxidation

Abstract In industrial catalysis, alkali cations are frequently used to promote activity or selectivity. Scanning tunneling microscopy, ambient‐pressure X‐ray photoelectron spectroscopy, and density‐functional calculations were used to study the structure and reactivity of potassium oxides in contact with the Au(111) surface. Three different types of oxides (K 2 O 2 , K 2 O and KO y with y <0.5) were observed on top of the gold substrate at 300–525 K. Initially, small aggregates of K 2 O 2 /K 2 O (1–2 nm in size) were seen at the elbows of the herringbone structure. After increasing the K coverage (>0.15 ML), large islands of the oxide (20–40 nm in size) appeared. These islands contained a mixture of K 2 O and KO y ( y <0.5). A key correlation was found involving the structure, oxidation state, and chemical activity of the alkali oxide. The small aggregates of potassium oxide had a very high catalytic activity for the oxidation of CO, being much more than plain promoters.

Shi, Rui↗
DOE OSTI2022

The Interaction of K and O 2 on Au(111): Multiple Growth Modes of Potassium Oxide and Their Catalytic Activity for CO Oxidation

Abstract In industrial catalysis, alkali cations are frequently used to promote activity or selectivity. Scanning tunneling microscopy, ambient‐pressure X‐ray photoelectron spectroscopy, and density‐functional calculations were used to study the structure and reactivity of potassium oxides in contact with the Au(111) surface. Three different types of oxides (K 2 O 2 , K 2 O and KO y with y <0.5) were observed on top of the gold substrate at 300–525 K. Initially, small aggregates of K 2 O 2 /K 2 O (1–2 nm in size) were seen at the elbows of the herringbone structure. After increasing the K coverage (>0.15 ML), large islands of the oxide (20–40 nm in size) appeared. These islands contained a mixture of K 2 O and KO y ( y <0.5). A key correlation was found involving the structure, oxidation state, and chemical activity of the alkali oxide. The small aggregates of potassium oxide had a very high catalytic activity for the oxidation of CO, being much more than plain promoters.

Shi, Rui↗
DOE OSTI2022

CO 2 Hydrogenation to Methanol over Inverse ZrO 2 /Cu(111) Catalysts: The Fate of Methoxy under Dry and Wet Conditions

Understanding the surface chemistry of CH 3 O species is essential for the production of methanol by CO 2 hydrogenation over Cu-based heterogeneous catalysts, as it facilitates the rational design of more efficient conversion processes. Recent research has identified inverse ZrO 2 /Cu catalysts as highly active and selective systems for the transformation of CO 2 to methanol with a performance that can be better than that of commercial Cu/ZnO catalysts. Here, we employed synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and calculations based on density functional theory (DFT) to understand the fate of CH 3 O groups under dry and wet environments. AP-XPS spectra revealed that under CO 2 hydrogenation conditions, formate and methoxy are two key intermediates to produce methanol. Furthermore, there are three different types of reactive sites on the surface: One is active for methoxy adsorption, which is stable and responsible for the methanol synthesis; Another one transforms CO 2 into CO; and a third one is active for CO 2 and methoxy dissociation, leading to C and methane formation. The theoretical calculations indicate that CH 3 OH readily dissociates to CH 3 O species following a highly exothermic (ΔE = -20.99 kcal/mol) and barrierless process. The water produced by the reverse water-gas shift reaction (CO 2 + H 2 → H 2 O + CO) can prevent the decomposition of CH 3 O species. We discovered that by introducing a tiny amount of water vapor (2 × 10 -6 Torr) into the reaction chamber, the energy barrier for the reaction CH 3 O(ads) + H(ads) → CH 3 OH(gas) is dramatically reduced. AP-XPS and computational modelling showed that water is quite capable of extracting adsorbed methoxy to form gaseous methanol. With this in mind, one could boost the methanol selectivity by adding appropriate amounts of water or steam, which is an inexpensive and feasible solution for industrial operations.

36 MATERIALS SCIENCE↗