Engineering topics
Wang, Bo
Publications and source records attributed to Wang, Bo.
Formation of Nitrogen Bubbles During Solidification of Duplex Stainless Steels
The nucleation and growth of nitrogen bubbles for duplex stainless steels are of great significance for the formation mechanism of bubbles during solidification. In the current study, numerical method and theoretical analysis of formula derivation were used to study the formation of nitrogen bubbles during solidification. The critical sizes of the bubble for homogeneous nucleation and heterogeneous nucleation at the solid–liquid interface during solidification were derived theoretically by the classical nucleation theory. The results show that the calculated values for the solubility of nitrogen in duplex stainless steel are in good agreement with the experimental values which are quoted by references: for example, when the temperature T = 1823 K and the nitrogen partial pressure P{sub N 2 =40P Θ , the calculated value (0.8042 wt pct) for the solubility of Fe-12Cr alloy nitrogen in molten steel is close to the experimental value (0.780 wt pct). Moreover, the critical radii for homogeneous nucleation and heterogeneous nucleation are identical during solidification. On the one hand, with the increasing temperature or the melt depth, the critical nucleation radius of bubbles at the solid–liquid interface increases, but the bubble growth rate decreases. On the other hand, with the decreasing initial content of nitrogen or the cooling rate, the critical nucleation radius of bubbles at the solid–liquid interface increases, but the bubble growth rate decreases. Furthermore, when the melt depth is greater than the critical depth, which is determined by the technological conditions, the change in the Gibbs free energy for the nucleation is not conducive enough to form new bubbles.
Unlocking the photobiological conversion of CO 2 to ( R )-3-hydroxybutyrate in cyanobacteria
Mitigation of a bottleneck significantly improved ( R )-3HB productivity, and metabolic flux analysis delineated dramatic metabolic flux changes in cyanobacterium Synechocystis .
Comparative investigation on microstructures and mechanical properties of (TiB + TiC)/Ti-6Al-4V composites from Ti-B4C-C and Ti-TiB2-TiC systems
Highlights: • The (TiB{sub w}+TiC{sub p})/Ti-6Al-4V composites were fabricated from Ti-B{sub 4}C-C and Ti-TiB{sub 2}-TiC systems by reactive hot-pressed sintering. • Microstructures and mechanical properties of the two kinds of composites were comparatively investigated. • The composites from Ti-TiB{sub 2}-TiC system possess higher elastic modulus and Vickers hardness than those from Ti-B{sub 4}C-C system. • The composites from Ti-TiB{sub 2}-TiC system have higher bending strength than the other system while employing same conditions. • The composites from Ti-B{sub 4}C-C system present better abrasion resistance than those from Ti-TiB{sub 2}-TiC system. - Abstract: Two percentages of TiB + TiC reinforced Ti-6Al-4V composites from Ti-B{sub 4}C-C and Ti-TiB{sub 2}-TiC systems were fabricated by reactive hot-pressed sintering. Their microstructures and mechanical properties involving elastic modulus, Vickers hardness, bending strength and wear property were investigated comparatively. The experimental results show that needle-like TiB whiskers and near-equiaxed TiC particles are evenly distributed in the Ti-6Al-4V matrix. The mechanical properties of the (TiB + TiC)/Ti-6Al-4V composites are closely related with the nominal composition and synthesis system of TiB + TiC reinforcement and the microstructures of composites. With increasing the nominal volume fraction of reinforcement, both elastic modulus and Vickers hardness increase more or less and the bending strength decreases in varying degrees. A certain increase of pores in the composites with the sintering temperature increasing to 1300 °C can markedly affect the bending strength. Moreover, no matter what the sintering temperature and nominal volume fraction of reinforcement, the elastic modulus and Vickers hardness of composites from the Ti-TiB{sub 2}-TiC system are higher than those from the Ti-B{sub 4}C-C system. Similarly, the composites from the Ti-B{sub 4}C-C system present better abrasion resistance than those from the Ti-TiB{sub 2}-TiC system due to the difference of interfacial bonding between the TiC particles and Ti-6Al-4V matrix in the two kinds of composites.
Conductive open frameworks
The disclosure relates generally to materials that comprise conductive covalent organic frameworks. The disclosure also relates to materials that are useful to store and separate gas molecules and sensors.
Defect-Induced Photoluminescence Enhancement and Corresponding Transport Degradation in Individual Suspended Carbon Nanotubes
The utilization of defects in carbon nanotubes to improve their photoluminescence efficiency has become a widespread study towards the realization of efficient light emitting devices. Here, we report a detailed comparison of defects in nanotubes (quantified by Raman spectroscopy) and photoluminescence (PL) intensity of individual suspended carbon nanotubes (CNTs). We have also the evaluated the impact of these defects on the electron/hole transport in the nanotubes, which is crucial for the ultimate realization of optoelectronic devices. We find that brightly luminescent nanotubes exhibit a pronounced D-band in their Raman spectra, and vice versa, dimly luminescent nanotubes exhibit almost no D-band. Here, defects are advantageous for light emission by trapping excitons, which extends their lifetimes. We quantify this behavior by plotting the PL intensity as a function of the I D /I G band Raman intensity ratio, which exhibits a Lorentz distribution peaked at I D /I G =0.17. For CNTs with a I D /I G ratio >0.25, the PL intensity decreases, indicating that, above some critical density, non-radiative recombination at defect sites dominates over the advantages of exciton trapping. In an attempt to fabricate optoelectronic devices based on these brightly luminescent CNTs, we transferred these suspended CNTs to platinum electrodes and found that the brightly photoluminescent nanotubes exhibit nearly infinite resistance due to these defects while those without bright photoluminescence exhibit finite resistance. These findings indicate a potential limitation in the use of brightly luminescent CNTs for optoelectronic applications.
Two Distinct Mechanisms for C–C Desaturation by Iron(II)- and 2-(Oxo)glutarate-Dependent Oxygenases: Importance of α-Heteroatom Assistance
Abstract not provided
Efficiently enhanced photoluminescence in Eu3+-doped Lu2(MoO4)3 by Gd3+ substituting
Highlights: • The Gd{sup 3+} doped samples had been discovered to show much better luminescent properties than Lu{sub 2}(MoO{sub 4}){sub 3}:0.02Eu{sup 3+}. • The influence of Gd{sup 3+} ions on luminescence behavior was discussed. • The DFT calculation indicates that the structure of Gd{sub 2}(MoO{sub 4}){sub 3} is more propitious for luminescence than that of Lu{sub 2}(MoO{sub 4}){sub 3}. - Abstract: A series of Lu{sub 2-x}Gd{sub x}(MoO{sub 4}){sub 3}:0.02Eu{sup 3+} (x = 0–2) red-emitting phosphors have been synthesized by the standard solid-state reaction method. Interestingly, the Gd concentration plays a profound role to influence the luminescence property. A conspicuous monotonic increase could be found in the influence of Gd{sup 3+} concentration to the emission intensity, and finally Gd{sub 2}(MoO{sub 4}){sub 3}:0.02Eu{sup 3+} exhibits the strongest red light emission with the intensifying factor even reaching 3.04-fold compared to Lu{sub 2}(MoO{sub 4}){sub 3}:0.02Eu{sup 3+}. Careful structural analysis suggested that up to about 80% (x = 1.6) Lu can be substituted by Gd with the same crystal structure of Lu{sub 2}(MoO{sub 4}){sub 3} being retained, while a higher Gd concentration would lead to it crystallizing in the Gd{sub 2}(MoO{sub 4}){sub 3} structure. We believe that the variation of crystal structure is responsible for the photoluminescence enhancing process.
Biological production of organic compounds
Methods of producing ethylene oxide and ethylene glycol are disclosed herein. Ethylene produced by cyanobacteria engineered to express ethylene-forming enzymes may be converted to ethylene oxide by bacteria engineered to express a monooxygenase enzyme. Ethylene oxide may be converted to ethylene glycol by exposure to an acidic solution. The methods may be performed in a bioreactor.
Study on anisotropy of n-type Mg 3 Sb 2 -based thermoelectric materials
The recent discovery of a high thermoelectric figure of merit (ZT) in an n-type Mg 3 Sb 2 -based Zintl phase triggered an intense research effort to pursue even higher ZT. Based on our previous report on Mg 3.1 Nb 0.1 Sb 1.5 Bi 0.49 Te 0.01 , we report here that partial texturing in the (001) plane is achieved by double hot pressing, which is further confirmed by the rocking curves of the (002) plane. The textured samples of Mg 3.1 Nb 0.1 Sb 1.5 Bi 0.49 Te 0.01 show a much better average performance in the (00l) plane. Hall mobility is significantly improved to ~105 cm 2 V -1 s -1 at room temperature in the (00l) plane due to texturing, resulting in higher electrical conductivity, a higher power factor of ~18 μW cm -1 K -2 at room temperature, and also higher average ZT. This work shows that texturing is good for higher thermoelectric performance, suggesting that single crystals of n-type Mg 3 Sb 2 -based Zintl compounds are worth pursuing.
Tunneling Hot Spots in Ferroelectric SrTiO 3
Strontium titanate (SrTiO 3 ) is the “silicon” in the emerging field of oxide electronics. While bulk properties of this material have been studied for decades, new unexpected phenomena have recently been discovered at the nanoscale, when SrTiO 3 forms an ultrathin film or an atomically sharp interface with other materials. One of the striking discoveries is room-temperature ferroelectricity in strain-free ultrathin films of SrTiO 3 driven by the TiSr antisite defects, which generate a local dipole moment polarizing the surrounding nanoregion. Here, we demonstrate that these polar defects are not only responsible for ferroelectricity, but also propel the appearance of highly conductive channels, “hot spots”, in the ultrathin SrTiO 3 films. Using a combination of scanning probe microscopy experimental studies and theoretical modeling, we show that the hot spots emerge due to resonant tunneling through localized electronic states created by the polar defects and that the tunneling conductance of the hot spots is controlled by ferroelectric polarization. Our finding of the polarization-controlled defect-assisted tunneling reveals a new mechanism of resistive switching in oxide heterostructures and may have technological implications for ferroelectric tunnel junctions. It is also shown that the conductivity of the hot spots can be modulated by mechanical stress, opening a possibility for development of conceptually new electronic devices with mechanically tunable resistive states.
A Genetic Toolbox for Modulating the Expression of Heterologous Genes in the Cyanobacterium Synechocystis sp. PCC 6803
Cyanobacteria, genetic models for photosynthesis research for decades, have recently become attractive hosts for producing renewable fuels and chemicals, owing to their genetic tractability, relatively fast growth, and their ability to utilize sunlight, fix carbon dioxide, and in some cases, fix nitrogen. Despite significant advances, there is still an urgent demand for synthetic biology tools in order to effectively manipulate genetic circuits in cyanobacteria. In this study, we have compared a total of 17 natural and chimeric promoters, focusing on expression of the ethylene-forming enzyme (EFE) in the cyanobacterium Synechocystis sp. PCC 6803. We report the finding that the E. coli σ 70 promoter Ptrc is superior compared to the previously reported strong promoters, such as PcpcB and PpsbA, for the expression of EFE. In addition, we found that the EFE expression level was very sensitive to the 5'-untranslated region upstream of the open reading frame. A library of ribosome binding sites (RBSs) was rationally designed and was built and systematically characterized. We demonstrate a strategy complementary to the RBS prediction software to facilitate the rational design of an RBS library to optimize the gene expression in cyanobacteria. Our results show that the EFE expression level is dramatically enhanced through these synthetic biology tools and is no longer the rate-limiting step for cyanobacterial ethylene production. Furthermore, these systematically characterized promoters and the RBS design strategy can serve as useful tools to tune gene expression levels and to identify and mitigate metabolic bottlenecks in cyanobacteria.
Avalanche Photoemission in Suspended Carbon Nanotubes: Light without Heat
Not provided.
The plasticity of cyanobacterial carbon metabolism
This opinion article aims to raise awareness of a fundamental issue which governs sustainable production of biofuels and bio-chemicals from photosynthetic cyanobacteria. Discussed is the plasticity of carbon metabolism, by which the cyanobacterial cells flexibly distribute intracellular carbon fluxes towards target products and adapt to environmental/genetic alterations. This intrinsic feature in cyanobacterial metabolism is being understood through recent identification of new biochemical reactions and engineering on low-throughput pathways. We focus our discussion on new insights into the nature of metabolic plasticity in cyanobacteria and its impact on hydrocarbons (e.g. ethylene and isoprene) production. Here, we discuss approaches that need to be developed to rationally rewire photosynthetic carbon fluxes throughout primary metabolism. We also outline open questions about the regulatory mechanisms of the metabolic network that remain to be answered, which might shed light on photosynthetic carbon metabolism and help optimize design principles in order to improve the production of fuels and chemicals in cyanobacteria.
Radiation-induced direct bandgap transition in few-layer MoS 2
We report photoluminescence (PL) spectroscopy of air-suspended and substrate-supported molybdenum disulfide (MoS 2 ) taken before and after exposure to proton radiation. For 2-, 3-, and 4-layer MoS 2 , the radiation causes a substantial (>10×) suppression of the indirect bandgap emission, likely due to a radiation-induced decoupling of the layers. For all samples measured (including the monolayer), we see the emergence of a defect-induced shoulder peak at around 1.7 eV, which is redshifted from the main direct bandgap emission at 1.85 eV. Here, defects induced by the radiation trap the excitons and cause them to be redshifted from the main direct band emission. After annealing, the defect-induced sideband disappears, but the indirect band emission remains suppressed, indicating a permanent transition into a direct bandgap material. While suspended 2-, 3-, and 4-layer MoS 2 show no change in the intensity of the direct band emission after radiation exposure, substrate-supported MoS 2 exhibits an approximately 2-fold increase in the direct bandgap emission after irradiation. Suspended monolayer MoS 2 shows a 2–3× drop in PL intensity; however, substrate-supported monolayer MoS 2 shows a 2-fold increase in the direct band emission.
Controlled manipulation of oxygen vacancies using nanoscale flexoelectricity
Oxygen vacancies, especially their distribution, are directly coupled to the electromagnetic properties of oxides and related emergent functionalities that have implications for device applications. Here using a homoepitaxial strontium titanate thin film, we demonstrate a controlled manipulation of the oxygen vacancy distribution using the mechanical force from a scanning probe microscope tip. By combining Kelvin probe force microscopy imaging and phase-field simulations, we show that oxygen vacancies can move under a stress-gradient-induced depolarisation field. When tailored, this nanoscale flexoelectric effect enables a controlled spatial modulation. In motion, the scanning probe tip thereby deterministically reconfigures the spatial distribution of vacancies. Finally, the ability to locally manipulate oxygen vacancies on-demand provides a tool for the exploration of mesoscale quantum phenomena and engineering multifunctional oxide devices.
Phase-field based Multiscale Modeling of Heterogeneous Solid Electrolytes: Applications to Nanoporous Li 3 PS 4
Modeling the effective ion conductivities of heterogeneous solid electrolytes typically involves the use of a computer-generated microstructure consisting of randomly or uniformly oriented fillers in a matrix. But, the structural features of the filler/matrix interface, which critically determine the interface ion conductivity and the microstructure morphology, have not been considered during the microstructure generation. In using nanoporous β-Li 3 PS 4 electrolyte as an example, we develop a phase-field model that enables generating nanoporous microstructures of different porosities and connectivity patterns based on the depth and the energy of the surface (pore/electrolyte interface), both of which are predicted through density functional theory (DFT) calculations. Room-temperature effective ion conductivities of the generated microstructures are then calculated numerically, using DFT-estimated surface Li-ion conductivity (3.14×10 -3 S/cm) and experimentally measured bulk Li-ion conductivity (8.93×10 -7 S/cm) of β-Li 3 PS 4 as the inputs. We also use the generated microstructures to inform effective medium theories to rapidly predict the effective ion conductivity via analytical calculations. Furthemore, when porosity approaches the percolation threshold, both the numerical and analytical methods predict a significantly enhanced Li-ion conductivity (1.74×10 -4 S/cm) that is in good agreement with experimental data (1.64×10 -4 S/cm). The present phase-field based multiscale model is generally applicable to predict both the microstructure patterns and the effective properties of heterogeneous solid electrolytes.
Taguchi analysis of parameters for small-diameter single wall carbon nanotube growth
Not Available