Search NASA⌕ Search

Engineering topics

Wang, Chongmin

Publications and source records attributed to Wang, Chongmin.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗
DOE OSTI2021

A Polymer-in-Salt Electrolyte with Enhanced Oxidative Stability for Lithium Metal Polymer Batteries

Lithium (Li) metal polymer batteries (LMPBs) are a promising candidate of solid-state batteries with high safety. However, rare progress has been demonstrated so far in high voltage stability of polyethylene oxide (PEO) based polymer electrolytes for LMPBs. Herein, we revived the polymer-in-salt electrolyte (PISE) strategy based on the PEO-LiFSI system with EO/Li = 8 through a dry process to avoid the contamination of the residual solvent. The obtained PISEs exhibit quite different morphologies and coordination structures which greatly enhance the oxidative stability of polymer electrolytes. P(EO)1LiFSI has a low melting temperature, a high ionic conductivity at 60 ?C and an oxidative stability of ~4.5 V vs. Li/Li+ (overcoming the inherent low oxidative stability of PEO). With an effective interphase rich in inorganic species, in combination with good stability of the hybrid polymer electrolyte towards Li metal, the cycling stability of Li||LiNi1/3Co1/3Mn1/3O2 is greatly improved. The LMPB can retain 74.4% of capacity after 186 cycles at 60 ?C under the charge cutoff voltage of 4.3 V. The findings point out a promising strategy to develop high-voltage stable polymer electrolytes for high energy-density and safe LMPBs.

Polymer-in-salt electrolyte, lithium metal battery↗
DOE OSTI2021

Labile Fe(III) supersaturation controls nucleation and properties of product phases from Fe(II)-catalyzed ferrihydrite transformation

We report Fe(II)-catalyzed ferrihydrite (Fh) transformation to more crystalline iron (oxyhydr)oxide phases is a widely occurring geochemical process which has been extensively studied as a function of Fe(II)/Fh ratios at fixed Fh loadings. However, recent isolation of an intermediate Fe(III) species resulting from Fe(II)-Fh contact that facilitates transformation by dissolution/reprecipitation suggests that the kinetics and properties of product phases will instead depend mostly on its rate of accumulation to a critical concentration, consistent with principles in the classical nucleation theory (CNT). This suggests a dependence both on the loading of Fe(II) on the surface, which controls the rate of labile Fe(III) formation, as well as the available volume of solution, which also impacts how fast it can achieve its critical concentration to nucleate product phases. To specifically examine the latter effect, here we studied transformation of 15 mg Fh in 1 mM FeSO 4 solutions at pH 7.2 in batch suspensions of 30 mL, 150 mL, and 450 mL volumes. Time-dependent concentrations of aqueous Fe(II), surface-associated Fe(II), and resulting labile Fe(III) were monitored along with bulk solids characterization as a function of time. Transmission electron microscopy (TEM) was used to visualize the evolution of phases at identical locations on TEM grids. The collective results show that the rates of Fh loss and emergence of product lepidocrocite (Lp) and goethite (Gt) as well as their phase proportions, nucleation mode and morphological properties depend directly on the rate of accumulation of the labile Fe(III) precursor to its critical concentration, which in our experiments was controlled simply by varying the available volume of solution into which it enters. Statistical analyses of TEM image data suggest that while both heterogeneous and homogeneous nucleation occurred in all experiments, the former was increasingly favored at lower Fh/solution ratio due to its lower nucleation barrier being more favorable at attendant lower supersaturations of Fe(III).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Fluorination-Enhanced Surface Stability of Cation-Disordered Rocksalt Cathodes for Li-Ion Batteries

Cation-disordered rocksalt (DRX) materials have emerged as a class of novel high-capacity cathodes for Li-ion batteries. However, commercialization of DRX cathodes will require reducing their capacity decay, which has been associated with oxygen loss during cycling. Recent studies have shown that fluorination of DRX cathodes can effectively reduce the oxygen loss and improve the cycling stability; however, the underlying atomic-scale mechanisms remain elusive. Herein, using a combination of electrochemical measurements, scanning transmission electron microscopy, and electron energy loss spectroscopy, we examine the correlation between the electrochemical properties and structural evolution in Mn-redox-based DRX cathodes, Li1.2Ti0.4-xMn0.4+xO2.0-xFx (x = 0 and 0.2). We find that fluorination strongly suppresses structural amorphization and void formation initiated from the particle surface, therefore greatly enhancing the cyclability of the cathode. We further reveal a novel rocksalt-to-spinel-like structural transformation in the DRX bulk, which surprisingly contributes to a gradual capacity increase during cycling. Our results provide important insight for the design of novel DRX cathodes with high capacity and long cycle life.

Li, Linze↗
DOE OSTI2021

Advanced Low‐Flammable Electrolytes for Stable Operation of High‐Voltage Lithium‐Ion Batteries

Abstract Despite being an effective flame retardant, trimethyl phosphate (TMP a ) is generally considered as an unqualified solvent for fabricating electrolytes used in graphite (Gr)‐based lithium‐ion batteries as it readily leads to Gr exfoliation and cell failure. In this work, by adopting the unique solvation structure of localized high‐concentration electrolyte (LHCE) to TMP a and tuning the composition of the solvation sheaths via electrolyte additives, excellent electrochemical performance can be achieved with TMP a ‐based electrolytes in Gr∥LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells. After 500 charge/discharge cycles within the voltage range of 2.5–4.4 V, the batteries containing the TMP a ‐based LHCE with a proper additive can achieve a capacity retention of 85.4 %, being significantly higher than cells using a LiPF 6 ‐organocarbonates baseline electrolyte (75.2 %). Meanwhile, due to the flame retarding effect of TMP a , TMP a ‐based LHCEs exhibit significantly reduced flammability compared with the conventional LiPF 6 ‐organocarbonates electrolyte.

Jia, Hao↗
DOE OSTI2021

Advanced Low-Flammable Electrolytes for Stable Operation of High-Voltage Lithium-Ion Batteries

Despite being an effective flame retardant, trimethyl phosphate (TMP a ) is generally considered as an unqualified solvent for fabricating electrolytes used in graphite (Gr) based lithium ion batteries as it readily leads to Gr exfoliation and cell failure. In this work, by adopting the unique solvation structure of localized high-concentration electrolyte (LHCE) to TMP a and tuning the composition of the solvation sheath via electrolyte additive, excellent electrochemical performance can be achieved with TMPa based electrolytes in Gr||LiNi 0.8 Mn 0.1 Co 0.1 O 2 cells. After 500 charge/discharge cycles within the voltage range of 2.5-4.4 V, the batteries containing TMPa based LHCEs with proper additive can achieve a capacity retention of 85.4%, being significantly higher than cells using a LiPF 6 -organocarbonates baseline electrolyte (75.2%). Meanwhile, due to the flame retarding effect of TMP a , TMP a based LHCEs exhibit significantly reduced flammability compared with the conventional LiPF 6 -organocarbonates electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Origin, nature, and the dynamic behavior of nanoscale vacancy clusters in Ni-rich layered oxide cathodes

Oxygen and transition metal (TM) vacancies in transition metal oxides (TMOs) play an important role in materials functionalities. For TMO cathodes of Li-ion batteries, vacancies can be introduced, either deliberately or inevitably, during materials synthesis or upon electrochemical cycling. Effects of vacancies on the electrochemical properties of cathodes critically depend on the dynamic characteristics of vacancies during the battery cycling. However, a fundamental understanding of such characteristics in the layer structured cathode remains elusive. Here, using scanning transmission electron microscopy (STEM), we reveal a cycling-induced aggregation behavior of oxygen and TM vacancies in a Ni-rich layer structured cathode of secondary particles. We discover that during the initial charging, vacancies aggregate to form visible vacancy-rich nanoregions (vacancy clusters) firstly at the outer layer of the secondary particle, and then the vacancy-cluster populated region extends to the inner part of particle upon fully charged. The spatial distinction of preferential nucleation of vacancy clusters at the outer layer indicates that the vacancy migration and clustering is associated with Li migration flux, which is larger at the outer layer, as all the Li from the inner part has to go through the outer layer. With extended cycling (> 50), these vacancy clusters become immobilized. We further reveal that the generation of these vacancy clusters is correlated to the material-synthesis conditions. Our findings solve a long-standing puzzle on the origin, nature, and behavior of the commonly visible vacancy clusters in the NMC cathode, providing insights on correlation between properties and dynamic behaviors of atomic-scale defects in layered oxide cathodes.

Li-ion batteries, layered oxide cathodes, NMC, cat↗
DOE OSTI2021

Polymer-ceramic composite electrolytes for all-solid-state lithium batteries: Ionic conductivity and chemical interaction enhanced by oxygen vacancy in ceramic nanofibers

Perovskite Li 3x La 2/3-x TiO3 (LLTO) nanofibers have been heat-treated in the hydrogen-containing atmosphere and then incorporated with the poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) polymer to form a composite electrolyte. Hydrogen treatment has created oxygen vacancies in the LLTO nanofibers, which has reduced the activation energy of Li ion transport along intra-grains and inter-grains, leading to improvement in the ion conductivity of LLTO nanofibers. Hydrogen treatment of the LLTO nanofibers has also enhanced the chemical interaction between the LLTO nanofibers and the polymer matrix in the composite electrolyte, and favored the Li ion transport at the nanofiber/polymer interface, improving the ion conductivity of the composite electrolyte to 3.4×10- 4 S/cm at room temperature. As a result, the Li|composite-electrolyte|Li half-cell exhibits good stability during lithium plating/stripping cycling at room temperature, showing an overpotential of ~91 mV at a constant current density of 0.5 mA/cm 2 . Finally, the full-cell battery with the composite electrolyte, lithium metal anode and lithium iron phosphate cathode shows excellent rate capacity and cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2021

Electrolyte Regulating toward Stabilization of Cobalt-Free Ultrahigh-Nickel Layered Oxide Cathode in Lithium-Ion Batteries

Cobalt (Co)-free ultrahigh-nickel (Ni) layered oxides exhibit a double-edged competitive advantages in reducing the cathode cost and boosting the energy density, promising the sustainable development of batteries for electric vehicles. However, the increased Ni content, resultantly more highly oxidative Ni 4+ , potentially induces severe capacity fading due to the aggravated side reactions, limiting the practical applications. Here, we evaluate the compatibility of two localized high-concentration electrolytes (LHCEs) with LiNi 0.96 Mg 0.02 Ti 0.02 O 2 (NMT) cathode under a high charging voltage of 4.4 V in lithium ion batteries. The LHCE with EC additive enables the formation of stable interfacial layers on both NMT cathode and graphite anode, thus realizing a capacity retention of 97.2% over 200 cycles at 25 °C and high reversible capacities of ~180.2 and ~185.8 mAh g -1 , respectively, at 5C charge rate and 5C discharge rate. This study offers a promising approach to enable Co-free ultrahigh-Ni layered oxides for practical applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Effects of fluorinated solvents on electrolyte solvation structures and electrode/electrolyte interphases for lithium metal batteries

Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next generation high-density energy storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structure. Types of fluorinated co-solvents used in LHCEs are investigated here in searching for the most suitable diluent for high concentration electrolytes (HCEs). Non-solvating solvents (including fluorinated ethers, fluorinated borate and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through co-participation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery-performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.

Cao, Xia↗
DOE OSTI2021

Recent progress in understanding solid electrolyte interphase on lithium metal anode

Lithium (Li) metal batteries (LMBs) are among the most promising candidates of next-generation high-energy-density rechargeable batteries. Solid electrolyte interphase (SEI) on Li metal anode plays a significant role which influences the Li deposition morphology and the cycle life of LMBs. Although SEI is the most important part, a thorough understanding of SEI is inadequate. In this review, we focus on the progresses of understanding on structures, properties and influencing factors of SEI as well as efficient strategies of tailoring SEI. First, the compositions, models and recent progresses on characterizing atomic structure of SEI are summarized. Second, the properties of SEI, including electronic conduction, ionic conduction, stability and mechanical properties are elucidated. Structures and properties of SEI are greatly influenced by multiple factors such as solvent, salt, additive, solvation structure, impurity, current density, temperature, pressure and capacity utilization. Thus, interactions between these factors and SEI are comprehensively discussed. Correlations of SEI with Li deposition morphology, rate capability and cycle life are further summarized. Moreover, efficient strategies of tailoring SEI with desired properties, including in-situ SEI and ex-situ SEI are also reviewed. Despite the significant progresses that have been achieved in the researches of SEI, better understanding of SEI is still highly demand. Finally, future directions especially in-operando techniques, multi-modality approaches for characterization of SEI and artificial intelligence assisted understanding of correlation between electrolyte components and SEI properties are proposed.

Wu, Haiping↗
DOE OSTI2021

Oxygen Vacancies Enriched Bi Based Catalysts for Enhancing Electrocatalytic CO2 Reduction to Formate

The practical application of CO2 conversion through electrochemical reduction is still hindered by the lack of high performance and cost-effective catalysts. It is thus imperative to explore feasible strategies for scalable fabrication of catalysts for CO2 reduction to targeting products with high efficiency. Herein, for the first time, a hybrid of BiOx encapsulated in carbon thin layer is developed as high active electrocatalyst for CO2 conversion, which is synthesized by pyrolysis using Bi MOF as precursor and sacrificial template. The carbon layer overcoating BiOx catalyst exhibits superior performance for CO2 reduction to formate, achieving a maximum Faradaic efficiency of 89.3 % and a maximum current density of 37.8 mA cm-2. It is found that the as-prepared BiOx catalyst is enriched with oxygen vacancies stabilized by the encapsulating carbon layer. Both the carbon layer and oxygen vacancies improve the charge transfer of the catalyst, in favor of the high formate current density. The defects of oxygen vacancies play a vital role in CO2 adsorption and activation and thereby further enhancing the electrocatalytic ability for formate production.

oxygen vacancy, bismuth, carbon coating, CO2 elect↗
DOE OSTI2021

Mesoscale-architecture-based crack evolution dictating cycling stability of advanced lithium ion batteries

The cracking phenomenon of Ni-rich NMC (LiNixMnyCo1-x-yO2, x = 0.6) secondary particles is frequently discovered and believed to be one of critical reasons deteriorating the long-term cycling stability of NMC cathode in lithium ion batteries (LIBs). However, the initiation and evolution of those cracks is still controversial due to the limited quantification especially by in situ monitoring, leading to the challenge of identifying an efficient approach to inhibit the formation of the fractures during repeated cycling. Herein, the irreversible, anisotropic cycling lattice and mesoscale expansion/shrinkage of nano-grain during the first cycle, as revealed by in situ X-ray diffraction (XRD) and in situ atomic force microscopy (AFM), have been quantified and confirmed to be the dominant driving forces of microcracks initiation at the grain boundaries. These microcracks preferentially nucleates at the core region with random oriented nano-grains in early stage. The further growth and aggregation of microcracks into macrocrack eventually results in microfracture propagation radially outward to the periphery region with more uniform nano-grain orientation. This mesoscale nano-grain architecture controlled cracking process highlight the importance of predictive synthesis of cathode materials with controllable multiscale crystalline architecture for high-performance LIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Understanding Reactivities of Ni-rich Li[NixMnyCo1-x-y]O2 Single-Crystal Cathode Materials

While Ni-rich Li[NixMnyCo1-x-y]O2 (NMC, x ? 0.8) compounds are considered the most promising cathode materials for high-energy lithium-ion batteries (LIBs), a significant challenge is the higher reactivities caused by the increased Ni content, especially under high-voltage operation conditions. In the present study, we synthesize three single-crystal NMC (SC-NMC) samples with the same particle size and morphology: LiNi0.8Mn0.1Co0.1O2 (NMC811), LiNi0.80Mn0.15Co0.05O2 (NMC80155) and LiNi0.85Mn0.10Co0.05O2 (NMC85105). By systematically varying the composition while controlling other properties, the role of each transition metal during air exposure, thermal treatment and long-term cycling is clearly demonstrated. We reveal that while higher Ni content leads to an overall increased reactivities, the presence of Mn provides a stabilizing effect on thermal, structural and chemical properties. In the absence of cycling-induced particle cracking, surface reconstruction is shown to be the dominating contributor to cathode capacity fade. Our study provides key insights needed for the development of better-performing Ni-rich NMC cathode materials.

Kim, Minkyung↗