Engineering topics

Wang, Daiwei

Publications and source records attributed to Wang, Daiwei.

8 records

DOE OSTI2024

Hybrid polymer network cathode-enabled soluble-polysulfide-free lithium–sulfur batteries

Among the emerging 'beyond lithium-ion' technologies for maximized sustainability, lithium-sulfur (Li-S) is a favoured chemistry because of its exceptional energy density from the conversion of sulfur, an element in abundant supply. However, the dissolution of several intermediate polysulfides formed during conversion leads to rapid performance degradation over cycling. Here, in this study, we address this issue by sulfurizing a hybrid polymer network with polyphosphazene and carbon as a cathode for Li-S batteries. With rich sites to re-bond and adsorb dissociative sulfur species, this hybrid polymer network circumvents the formation of soluble polysulfides and enables a unique, reversible inserting conversion reaction. Thus, our cathode delivers both high capacity (~900 mAh g -1 cathode ) and excellent cycling stability in Li-S coin cells, with a pouch cell demonstration of projected energy density of ~300 Wh kg -1 and 84.9% capacity retention after 150 cycles. The strategy can be extended to other cost-effective, recyclable polymers, advancing sulfur-based batteries towards practical energy storage application.

25 ENERGY STORAGE↗

DOE OSTI2024

All‐Solid‐State Lithium–Sulfur Batteries of High Cycling Stability and Rate Capability Enabled by a Self‐Lithiated Sn‐C Interlayer

Abstract All‐solid‐state lithium–sulfur batteries (ASSLSBs) have attracted intense interest due to their high theoretical energy density and intrinsic safety. However, constructing durable lithium (Li) metal anodes with high cycling efficiency in ASSLSBs remains challenging due to poor interface stability. Here, a compositionally stable, self‐lithiated tin (Sn)‐carbon (C) composite interlayer (LSCI) between Li anode and solid‐state electrolyte (SSE), capable of homogenizing Li‐ion transport across the interlayer, mitigating decomposition of SSE, and enhancing electrochemical/structural stability of interface, is developed for ASSLSBs. The LSCI‐mediated Li metal anode enables stable Li plating/stripping over 7000 h without Li dendrite penetration. The ASSLSBs equipped with LSCI thus exhibit excellent cycling stability of over 300 cycles (capacity retention of ≈80%) under low applied pressure (<8 MPa) and demonstrate improved rate capability even at 3C. The enhanced electrochemical performance and corresponding insights of the designed LSCI broaden the spectrum of advanced interlayers for interface manipulation, advancing the practical application of ASSLSBs.

Ye, Lei↗

DOE OSTI2024

Interfacial solvation-structure regulation for stable Li metal anode by a desolvation coating technique

Rechargeable lithium (Li) metal batteries face challenges in achieving stable cycling due to the instability of the solid electrolyte interphase (SEI). The Li-ion solvation structure and its desolvation process are crucial for the formation of a stable SEI on Li metal anodes and improving Li plating/stripping kinetics. This research introduces an interfacial desolvation coating technique to actively modulate the Li-ion solvation structure at the Li metal interface and regulate the participation of the electrolyte solvent in SEI formation. Through experimental investigations conducted using a carbonate electrolyte with limited compatibility to Li metal, the optimized desolvation coating layer, composed of 12-crown-4 ether-modified silica materials, selectively displaces strongly coordinating solvents while simultaneously enriching weakly coordinating fluorinated solvents at the Li metal/electrolyte interface. This selective desolvation and enrichment effect reduce solvent participation to SEI and thus facilitate the formation of a LiF-dominant SEI with greatly reduced organic species on the Li metal surface, as conclusively verified through various characterization techniques including XPS, quantitative NMR, operando NMR, cryo-TEM, EELS, and EDS. The interfacial desolvation coating technique enables excellent rate cycling stability (i.e., 1C) of the Li metal anode and prolonged cycling life of the Li||LiCoO 2 pouch cell in the conventional carbonate electrolyte (E/C 2.6 g/Ah), with 80% capacity retention after 333 cycles.

42 ENGINEERING↗

DOE OSTI2022

Stable all-solid-state sodium-sulfur batteries for low-temperature operation enabled by sodium alloy anode and confined sulfur cathode

All-solid-state sodium-sulfur (Na-S) batteries are promising for stationary energy storage devices because of their low operating temperatures (less than 100 °C), improved safety, and low-cost fabrication. Using Na alloy instead of Na metal as an anode in Na-S batteries can prevent dendrite growth and improve interfacial stability between the anode and solid electrolytes to achieve long-cycling stability. A high-sulfur content cathode possessing high sulfur utilization is also important to enable an energy-dense Na-S battery. In this work, we studied Na-Sb and Na- Sn alloy anodes and demonstrated the superiority of Na 3 Sb alloy undergoing a stable Na alloying/dealloying process at 0.04 mA cm -2 for over 500 hours. Combining the optimized Na3Sb alloy anode with sulfur-carbon composites prepared by the vapor deposition approach, the full cell shows a high sulfur specific capacity and improved rate performance. Moreover, the all-solid-state Na alloy-S battery can deliver a high initial discharge specific capacity of 1377 mAh g -1 and maintain good capacity retention of 70 % after 180 cycles at 60 °C. Further, post-cycle characterizations show that both the anode and cathode perform a reversible discharge/charge process after the 1st cycle, and the cathode undergoes significantly rearranged distributions of carbon and solid-state electrolytes after 180 cycles due to severe volume change induced by repeated sodiation/desodiation process.

25 ENERGY STORAGE↗

DOE OSTI2022

A Superior Carbonate Electrolyte for Stable Cycling Li Metal Batteries Using High Ni Cathode

Li metal batteries pairing Li metal anode with high-nickel layer structured oxide cathode are a promising energy storage technology to achieve high energy density. To obtain long cycling life for Li metal batteries, the electrolyte plays a pivotal role in stabilizing both the Li metal anode and the high-nickel cathode upon electrochemical cycling. Herein, we report a carbonate electrolyte that enables a Li||LiNi 0.8 Mn 0.1 Co 0.1 O 2 pouch cell to achieve a high gravimetric energy density of 366 Wh/kg and unprecedented cycling stability with 80% capacity retention after 335 cycles. Here, the 19 F quantitative nuclear magnetic resonance spectroscopy and interface characterization demonstrate that FEC and LiDFOB can reduce the consumption rate of each other and the electrolyte, form a robust LiF-rich SEI on Li metal anode, and improve the microstructure integrity of the high-nickel cathode.

25 ENERGY STORAGE↗

DOE OSTI2020

Stable metal anodes enabled by a labile organic molecule bonded to a reduced graphene oxide aerogel

Significance Rechargeable batteries based on metal anodes are highly desirable due to their high energy density. However, the electrochemical interface is generally not favorable for metal deposition, resulting in dendritic metal growth and an unstable solid–electrolyte interphase (SEI). We altered the interface using a labile organic molecule, benzenesulfonyl fluoride. This molecule was bonded to the surface of a reduced graphene oxide aerogel, which not only guides uniform metal deposition but also enables formation of a stable SEI layer. The lithium metal batteries showed stable cycling and excellent tolerance to low-temperature operation. Stable sodium and zinc anodes were also realized, demonstrating the versatility of this concept.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Low-temperature and high-rate-charging lithium metal batteries enabled by an electrochemically active monolayer-regulated interface

Stable operation of rechargeable lithium (Li)-based batteries at low temperatures is vital for cold-climate applications but is plagued with dendritic Li plating and unstable solid-electrolyte interphase (SEI). Here we report high-performance Li-metal batteries under low-temperature and high-rate-charging conditions. This is realized by utilizing a self-assembled monolayer of electrochemically active molecules on current collectors that regulates the nanostructure and composition of SEI and deposition morphology of Li metal anodes. A multilayer SEI containing a LiF-rich inner phase and amorphous outer layer effectively seals the Li surface in contrast to the conventional impassive SEI at low temperatures. As a result, galvanic Li corrosion and self-discharge were suppressed; stable Li deposition was realized from -60º to 45ºC; and a Li|LiCoO 2 cell with a capacity of 2.0 mAh cm -2 displayed a 200-cycle life at -15ºC with a recharge time of 45 minutes.

25 ENERGY STORAGE↗

DOE OSTI2020

A new approach to both high safety and high performance of lithium-ion batteries

We present a novel concept to achieve high performance and high safety simultaneously by passivating a Li-ion cell and then self-heating before use. By adding a small amount of triallyl phosphate in conventional electrolytes, we show that resistances of the passivated cells can increase by ~5×, thereby ensuring high safety and thermal stability. High power before battery operation is delivered by self-heating to an elevated temperature such as 60°C within tens of seconds. The present approach of building a resistive cell with highly stable materials and then delivering high power on demand through rapid thermal stimulation leads to a revolutionary route to high safety when batteries are not in use and high battery performance upon operation.

36 MATERIALS SCIENCE↗