Search NASA⌕ Search

Engineering topics

Wang, H. Q.

Publications and source records attributed to Wang, H. Q..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Observation of fully detached divertor integrated with improved core confinement for tokamak fusion plasmas

Integration of divertor detachment with a high-performance (β N ~ 3, β p > 2, H 98 ~ 1.5) core plasma has been demonstrated in DIII-D high-β p (poloidal beta) plasmas associated with a sustained core internal transport barrier (ITB) and an H-mode edge transport barrier (ETB). Such good core-edge integration has been achieved for both neon and nitrogen seeding, for both favorable and unfavorable B-field directions, independently from the impurity puffing locations, though these variations play important roles on divertor characteristics. Compared to the standard H-mode plasmas, the high-β p plasma exhibits a much wider window of detachment compatible with high confinement core. Fully detached divertor plasmas with low plasma temperature (Te < 5 eV), low particle flux, and low heat flux across the entire divertor target plate were obtained by using nitrogen seeding. This detached high-β p plasma is compatible with a newly developed detachment control system which can help optimize the nitrogen gas flow rate. Several features, i.e., the high edge safety factor in the high-β p scenario, impurity injection, closed divertor and reduced heating power requirement due to the high confinement, facilitate the achievement of full divertor detachment at lower density. Instead of degrading global performance, the divertor detachment facilitates the access to an even stronger ITB at large radius with a relatively weak ETB through self-organized synergy between ITB and ETB, leading to sustained high confinement. The strengthening of the large-radius ITB compensates for the ETB degradation associated with divertor detachment. In addition, a weak ETB naturally has smaller edge localized modes (ELMs). In particular, with neon injection, a long-period no-ELM H-mode phase has been achieved simultaneously with high-performance core and partially detached divertor plasmas. Furthermore, these results demonstrate the possibility of integrating excellent core plasma performance with an effective divertor solution, an essential step toward steady-state operation of reactor-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Observation of quasi-coherent density fluctuation in scrape-off layer enhancing boundary transport in high-βN hybrid plasmas on DIII-D

In this work, we report the observation of a quasi-coherent density fluctuation (QCF) by the Doppler backscattering system in the scrape-off layer (SOL) region of the DIII-D tokamak. This QCF is observed in high power, high performance hybrid plasmas with near double-null divertor (DND) shape during the electron cyclotron heating period. This mode is correlated with a steepened SOL density profile, and leads to significantly elevated particle and heat fluxes between ELMs. The SOL QCF is a long-wavelength ion-scale fluctuation (k θ ρ s ≈0.2-0.4 and k r ρ s ≈0.03), and propagates in the ion diamagnetic direction in the plasma frame. Its radial expanse is about 1.5–2 cm, well beyond the typical width of heat flux λ q on DIII-D. Also, the SOL QCF does not show any clear dependence on the effective SOL collisionality, and thus may raise issues on the control of plasma-material interactions in low collisionality plasmas in which the blob-induced transport is reduced. A linear simulation using BOUT++ with a 5-field reduced model is performed and compared with experimental observations. In simulation results, an interchange-like density perturbation can be driven by the SOL density gradient, and its peak location and the radial width of the density perturbation are in agreement with the experimental observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Advances in physics understanding of high poloidal beta regime toward steady-state operation of CFETR

Experimental and modeling investigations of the high βp scenarios on the DIII-D and EAST tokamaks show advantages in high energy confinement, avoidance of n = 1 MHD, and core-edge integration with reduced heat flux, making this scenario an attractive option for CFETR steady-state operation. Experiments show that plasmas with high confinement and high density can be achieved with neutral beam injection on DIII-D (β p ~ 2.2, β N ~ 3.5, f BS ~ 50%, f Gw ~ 1.0, H 98y2 ~ 1.5) and pure RF power on EAST (β P ~ 2.0, β N ~ 1.6, f BS ~ 50%, f Gw ~ 0.8, H 98y2 > 1.3). By tailoring the current density profile, a q-profile with local (off-axis) negative shear is achieved that yields improved confinement and MHD stability. Transport analysis and simulation suggest that the combination of high density gradient and high Shafranov shift allows turbulence stabilization and higher confinement. Using on-axis ECH injection, tungsten accumulation is avoided on EAST, and this is reproduced in modeling. Reduced heat flux (by >40%) and maintenance of high core confinement is achieved with active feedback control of the radiated divertor, an important result for long pulse operation in tokamaks. In conclusion, the improved physics understanding and validated modeling tools are used to design a 1GW steady-state scenario for CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Progress of Divertor Heat and Particle Flux Control in EAST for Advanced Steady-State Operation in the Last 10 Years

Active control of the excessively high heat and particle fluxes on the divertor target plates is of fundamental importance to the steady state operation of tokamaks, especially for fusion reactors. A series of experiments have been carried out on this critical issue to relieve the plasma-wall interactions in the experimental advanced superconducting tokamak (EAST) in the last ten years, not only contributing to the long pulse operation of EAST itself, but also providing physical understandings and potential techniques to the next-generation devices like ITER. Here we have characterized the power deposition pattern and broadened the divertor footprint width effectively. The plasma-wetted area is actively handled using either 3-dimentional edge magnetic topology or advanced plasma equilibrium, thereby peak heat flux around the strike point is reduced. Active control of detachment or radiation compatible with core plasma performance has progressed significantly in very recent years, with a series of active feedback control modules developed and utilized successfully, based on the divertor physics advances with both experiments and simulation. The upper divertor of EAST was upgraded from graphite to active water-cooling ITER-like tungsten in 2014, exhibiting much enhanced heat removal capability. As for the particle exhaust including both fueling and impurity particles, in addition to wall conditioning and impurity source control, the efficiency of particle flux exhaust is optimized by making full use of the divertor closure and the plasma drifts in both scrape-off layer and divertor volume. These heat and particle exhaust advances contribute greatly to a series of EAST achievements like H-mode operation over 100 s. A brief near-term plan on the integrated control of divertor plasma-wall interactions in long-time scale will also be introduced, aiming to provide favorable divertor operation solution for ITER and CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

An analysis of controlled detachment by seeding various impurity species in high performance scenarios on DIII-D and EAST

Experiments at DIII-D and EAST have demonstrated simultaneous high confinement, divertor detachment, and active control of detachment level, all of which are required for ITER. Comparing detachment control via T e and J sat , it appears that is the most straightforward sensor to use for accessing detachment onset, while J sat offers more precise control of degree of detachment. Based on these results, control using nitrogen seeding has so far shown the best ability to follow a target value with the low disruptivity and little to no degradation of performance when an Internal Transport Barrier (ITB) is present, but not all facilities allow its use. Neon seeding also can be paired with feedback control with low impact on core performance as long as there is no disruption, however shots with neon seeding commonly disrupted during these experiments. Argon is effective in EAST, but tends to degrade performance (by ≈ 10%β p ) when detachment is achieved. With ideal conditions and strike point position control, data from a single Langmuir probe are an acceptable input to the control algorithm, but this simple system is easily defeated by strike point displacement comparable to the T e or J sat scale lengths. The presence of an ITB seems to be critical to retaining core performance in detachment in these parameter ranges, as the pedestal pressure tends to decrease as a result of impurity seeding.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Integration of full divertor detachment with improved core confinement for tokamak fusion plasmas

Divertor detachment offers a promising solution to the challenge of plasma-wall interactions for steady-state operation of fusion reactors. Here, we demonstrate the excellent compatibility of actively controlled full divertor detachment with a high-performance (β N ~ 3, H 98 ~ 1.5) core plasma, using high-β p (poloidal beta, β p > 2) scenario characterized by a sustained core internal transport barrier (ITB) and a modest edge transport barrier (ETB) in DIII-D tokamak. The high-β p high-confinement scenario facilitates divertor detachment which, in turn, promotes the development of an even stronger ITB at large radius with a weaker ETB. This self-organized synergy between ITB and ETB, leads to a net gain in energy confinement, in contrast to the net confinement loss caused by divertor detachment in standard H-modes. These results show the potential of integrating excellent core plasma performance with an efficient divertor solution, an essential step towards steady-state operation of reactor-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Grassy ELM regime at low pedestal collisionality in high-power tokamak plasma

Spontaneous mitigation of giant ELMs and appearance of grassy ELMs have been observed repeatedly at low pedestal collisionality (${\nu }_{\mathrm{e},\mathrm{p}\mathrm{e}\mathrm{d}}^{{\ast}}\sim 0.15$) in the high-power (P inj > 13 MW) hybrid scenario in DIII-D. Higher β p and higher q 95 appear to be beneficial to achieving the grassy ELM regime. The grassy ELM H-mode plasma shows high energy confinement performance (H 98y2 up to over 1.5) under the conditions of high neutral beam torque and high core rotation. The pedestal width appears to exceed the EPED1.0 model prediction by more than 50%. Pedestal stability analysis performed with the ELITE code indicates that the stability against low-n kink/peeling modes is improved with increased auxiliary heating power and the operational point in the grassy ELM regime is located near the ballooning boundary. The pedestal stability characteristics during the grassy ELM crashes have been investigated in comparison with the giant ELM crashes based on plasma profiles experimentally measured with high resolution and accuracy. It has been found that the underlying mechanism for the observed small-amplitude ELM crashes is mainly the expansion of the ballooning stability boundary induced by an initial radially localized collapse in the pedestal, which helps to stop the growth of instabilities and further collapse of the pedestal. The effect of electron density pedestal on mitigating edge localized instabilities has been analyzed by numerical simulation, suggesting that the electron density pedestal characterized by high n e,sep /n e,ped and low density gradient helps to stabilize peeling-ballooning modes because of a low pressure pedestal gradient and to lower the ballooning boundary mainly because of a low ion diamagnetic frequency in the pedestal region, thus triggering ballooning instabilities and producing the intrinsic grassy ELMs. Numerical simulation of the Chinese fusion engineering test reactor (CFETR) with the SOLPS code indicates that the separatrix density might be insensitive to the electron diffusivity in the pedestal region and increase with the power flowing from the core region to the edge region. Furthermore, pedestal stability analysis suggests that the flat density pedestal with high separatrix density obtained in the high-power plasma in CFETR would make the operational point close to the ballooning boundary, which is considered to help destabilize ballooning instabilities and facilitate the access to the grassy ELM regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Suppression of edge localized modes with real-time boron injection using the tungsten divertor in EAST

We report an observation of robust suppression of edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST), enabled by continuous boron (B) powder injection. Edge harmonic oscillations appear during B powder injection, providing sufficient particle transport to maintain constant density and avoid impurity accumulation in ELM-stable plasmas. Here, quasi-steady ELM suppression discharges are demonstrated with modest energy confinement improvement and over a wide range of conditions: heating power and technique variation, electron density range over a factor ~3.5, deuterium or helium ion species, and with either direction of the toroidal magnetic field. ELM suppression is observed above a threshold edge B intensity and ceases within 0.5 s of termination of the B injection. In contrast to ELM suppression accompanied by recycling reduction during Li powder injection in NSTX and EAST (Maingi et al 2018 Nucl. Fusion 58 024003), reduced recycling due to hydrogenic species retention is unnecessary for the ELM suppression with B powder injection, paving the way for its consideration as an ELM control tool for future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

First Evidence of Local E × B Drift in the Divertor Influencing the Structure and Stability of Confined Plasma near the Edge of Fusion Devices

The structure of the edge plasma in a magnetic confinement system has a strong impact on the overall plasma performance. Here we uncover for the first time a magnetic-field-direction dependent density shelf, i.e., local flattening of density radial profile near the magnetic separatrix, in high confinement plasmas with low edge collisionality in the DIII-D tokamak. The density shelf is correlated with a doubly peaked density profile near the divertor target plate, which tends to occur for operation with the ion BX∇B drift direction away from the X-point, as currently employed for DIII-D advanced tokamak scenarios. This double-peaked divertor plasma profile is connected via the EXB drifts, arising from a strong radial electric field induced by the radial electron temperature gradient near the divertor target. The drifts lead to the reversal of the poloidal flow above the divertor target, resulting in the formation of the density shelf. The edge density shelf can be also enhanced at higher heating power, preventing large, periodic bursts of the plasma, i.e. Edge-localized Modes, in the edge region, consistent with ideal magnetohydrodynamics calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

H-mode pedestal improvements with neon injection in DIII-D

Improvements in the H-mode pedestal pressure and global energy confinement were determined on DIII-D with both 3 and 6 MW of neutral beam (NBI) heating with neon injection. The pedestal pressure increased, primarily associated with a significant increase in the pedestal density with a relatively smaller decrease in the pedestal temperature. At the same neon injection rate, a rapid decrease in edge localized mode (ELM) frequency and ~35% increase in plasma stored energy were observed in the 3 MW discharge, while in the 6 MW discharge, the ELM frequency was gradually decreased and the plasma stored energy gradually increased by up to 20%. The measured pedestal widths from both 3 and 6 MW discharges matched the EPED1.0 width scaling, ${\Delta _{{\psi _N}}} = 0.089\beta _{p,ped}^{1/2}$ ,data-, within 20% deviations before and after neon injection. The peeling-ballooning mode (PBM) stability analysis showed that after neon injection, the ballooning stability boundary was increased, while the peeling stability boundary only dropped once the neon level was relatively high. The ballooning stability boundary increase with neon injection is consistent with increase of the ion diamagnetic stabilization (i.e. including the contribution from carbon, neon as well as deuterium ions) which is used in the criterion to determine when the calculated linear growth rates of PBM are unstable. Consequently, the new ELITE computed PBM boundaries were more consistent with the operating points than when only deuterium was included. This in turn suggests that the impurity may help to improve pedestal pressure through affecting ion diamagnetic frequency in the pedestal region, which could positively lead to the ballooning stability boundary extension.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Impact of divertor material on neutral recycling and discharge fueling in DIII-D

We report that experiments with the lower divertor of DIII-D during the Metal Rings Campaign (MRC) show that the fraction F of atomic D in the total recycling flux is material-dependent and varies through the ELM cycle, which may affect divertor fueling. Between ELMs, F C ~ 10% and FW ~ 40%, consistent with expectations if all atomic recycling is due to reflections. During ELMs, F C increases to 50% and F W to 60%. In contrast, the total D recycling coefficient including atoms and molecules R stays close to unity near the strike point where the surface is saturated with D. During ELMs, R can deviate from unity, increasing during high energy ELM-ion deposition (net D release) and decreasing at the end of the ELM which leads to ability of the target to trap the ELM-deposited D. The increase of R > 1 in response to an increase in ion impact energy Ei has been studied with small divertor target samples using Divertor Materials Evaluation System (DiMES). An electrostatic bias was applied to DiMES to change E i by 90 eV. On all studied materials including C, Mo, uncoated and W-coated TZM (>99% Mo, Ti, and Zr alloy), W, and W fuzz, an increase of E i transiently increased the D yield (and R) by ~10%. On C there was also an increase in the molecular D 2 yield, probably due to ion-induced D 2 desorption. Despite the measured increase in F on W compared to C, attached H-mode shots with OSP on W during MRC did not demonstrate a higher pedestal density. About 8% increase in the edge density could be seen only in attached L-mode scenarios. The difference can be explained by higher D trapping in the divertor and lower divertor fueling efficiency in H- versus L-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Separating divertor closure effects on divertor detachment and pedestal shape in DIII-D

Comparison between an open divertor and a more-closed divertor in DIII-D demonstrates detachment at an up to 40% lower pedestal density (n e,ped ) in the closed divertor, due to a combination of decreased fueling of the pedestal and increased dissipation in the scrape off layer (SOL) in the closed divertor, both resulting from increased neutral trapping in the divertor. Predicting whether the relationship between divertor closure and detachment will hold for an opaque SOL, in which the contribution of ionizing neutrals to fueling the pedestal is lessened, requires separating out the different mechanisms contributing to the density difference at detachment. A series of experiments on DIII-D characterizes matched discharges using various divertor configurations to isolate the effects of divertor closure. These experiments show detachment at up to 25% lower n e,sep in the closed divertor than the open, supported by simulations showing increased neutral trapping, and hence increased dissipation, in the closed divertor. A difference in n e,ped /n e,sep is also seen: for matched n e,sep , the closed divertor has up to 20% lower ne,ped, consistent with modeling showing a smaller ionization fraction inside the separatrix in this case. Understanding how these pieces fit together will help in develop of predictive models of pedestal density and detached divertors compatible with a high-performance core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Progress in DIII-D towards validating divertor power exhaust predictions

In this study, UEDGE simulations highlight the role of cross-field drifts on the onset of detached conditions, and new calibrated divertor vacuum ultra violet (VUV) spectroscopy is used to challenge the predictions of radiative constituents in these simulations. UEDGE simulations for DIII-D H-mode plasmas with the open divertor with the ion ∇B-drift towards the X-point show a bifurcated onset of the low field side (LFS) divertor detachment, consistent with experimentally observed step-like detachment onset (Jaervinen A.E. et al 2018 Phys. Rev. Lett. 121 075001). The divertor plasma in the simulations exhibits hysteresis in upstream separatrix density between attached and detached solution branches. Reducing the drift magnitude by a factor of 3 eliminates the step-like detachment onset in the simulations, confirming the strong role of drifts in the bifurcated detachment onset. When measured local plasma densities and temperatures are within proximity of predicted values in the simulations, there is no shortfall of the local emission of the dominant resonant radiating lines. However, the simulations systematically predict a factor of two lower total integrated radiated power than measured by the bolometer with the difference lost through radial heat flow out of the computational domain. Even though there is no shortfall in the emission of the dominant lines, a shortfall of total radiated power can be caused by underpredicted spatial extent of the radiation front, indicating a potential upstream or divertor transport physics origin for the radiation shortfall, or shortfall of radiated power in the spectrum between the dominant lines. In addition to the underpredicted spatial extent, in detached conditions, the simulations overpredict the peak radiation and dominant carbon lines near the X-point, which can be alleviated by manually increasing divertor diffusivity in the simulations, highlighting the ad hoc cross-field transport as one of the key limitations of the predictive capability of these divertor fluid codes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗