Search NASA⌕ Search

Engineering topics

Wang, Hansen

Publications and source records attributed to Wang, Hansen.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Onboard early detection and mitigation of lithium plating in fast-charging batteries

Fast-charging is considered as one of the most desired features needed for lithium-ion batteries to accelerate the mainstream adoption of electric vehicles. However, current battery charging protocols mainly consist of conservative rate steps to avoid potential hazardous lithium plating and its associated parasitic reactions. A highly sensitive onboard detection method could enable battery fast-charging without reaching the lithium plating regime. Here, we demonstrate a novel differential pressure sensing method to precisely detect the lithium plating event. By measuring the real-time change of cell pressure per unit of charge (dP/dQ) and comparing it with the threshold defined by the maximum of dP/dQ during lithium-ion intercalation into the negative electrode, the onset of lithium plating before its extensive growth can be detected with high precision. In addition, we show that by integrating this differential pressure sensing into the battery management system (BMS), a dynamic self-regulated charging protocol can be realized to effectively extinguish the lithium plating triggered by low temperature (0 °C) while the conventional static charging protocol leads to catastrophic lithium plating at the same condition. We propose that differential pressure sensing could serve as an early nondestructive diagnosis method to guide the development of fast-charging battery technologies.

25 ENERGY STORAGE↗
DOE OSTI2022

Cold-Starting All-Solid-State Batteries from Room Temperature by Thermally Modulated Current Collector in Sub-Minute

All-solid-state batteries (ASSBs) show great potential as high-energy and high-power energy storage devices but their attainable energy/power density at room temperature is severely reduced because of the sluggish kinetics of lithium-ion transport. Here we first reported a thermally modulated current collector (TMCC), which can rapidly cold-start ASSBs from room temperature to operating temperatures (70–90 °C) in less than one minute, and simultaneously enhance the transient peak power density by 15-fold compared to one without heating. This TMCC is prepared by integrating a uniform, ultrathin (~200 nm) nickel layer as a thermal modulator within an ultralight polymer-based current collector. By isolating the thermal modulator from the ion/electron pathway of ASSBs, it can provide fast, stable heat control yet does not interfere with regular battery operation. Moreover, this ultrathin (13.2 μm) TMCC effectively shortens the heat transfer pathway, minimizes heat losses, and mitigates the formation of local hot spots. The simulated heating energy consumption can be as low as ~3.94% of total battery energy. This TMCC design with good tunability opens new frontiers towards smart energy storage devices in the future from the current collector perspective.

25 ENERGY STORAGE↗
DOE OSTI2022

Suspension electrolyte with modified Li + solvation environment for lithium metal batteries

Designing a stable solid–electrolyte interphase on a Li anode is imperative to developing reliable Li metal batteries. In this work, we report a suspension electrolyte design that modifies the Li + solvation environment in liquid electrolytes and creates inorganic-rich solid–electrolyte interphases on Li. Li 2 O nanoparticles suspended in liquid electrolytes were investigated as a proof of concept. Through theoretical and empirical analyses of Li 2 O suspension electrolytes, the roles played by Li 2 O in the liquid electrolyte and solid–electrolyte interphases of the Li anode are elucidated. Also, the suspension electrolyte design is applied in conventional and state-of-the-art high-performance electrolytes to demonstrate its applicability. Based on electrochemical analyses, improved Coulombic efficiency (up to ~99.7%), reduced Li nucleation overpotential, stabilized Li interphases and prolonged cycle life of anode-free cells (~70 cycles at 80% of initial capacity) were achieved with the suspension electrolytes. We expect this design principle and our findings to be expanded into developing electrolytes and solid–electrolyte interphases for Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Rational solvent molecule tuning for high-performance lithium metal battery electrolytes

Electrolyte engineering improved cycling of Li metal batteries and anode-free cells at low current densities; however, high-rate capability and tuning of ionic conduction in electrolytes are desirable yet less-studied. In this study, we design and synthesize a family of fluorinated-1,2-diethoxyethanes as electrolyte solvents. The position and amount of F atoms functionalized on 1,2-diethoxyethane were found to greatly affect electrolyte performance. Partially fluorinated, locally polar –CHF 2 is identified as the optimal group rather than fully fluorinated –CF 3 in common designs. Paired with 1.2 M lithium bis(fluorosulfonyl)imide, these developed single-salt-single-solvent electrolytes simultaneously enable high conductivity, low and stable overpotential, >99.5% Li||Cu half-cell efficiency (up to 99.9%, ±0.1% fluctuation) and fast activation (Li efficiency >99.3% within two cycles). Combined with high-voltage stability, these electrolytes achieve roughly 270 cycles in 50-μm-thin Li||high-loading-NMC811 full batteries and >140 cycles in fast-cycling Cu||microparticle-LiFePO 4 industrial pouch cells under realistic testing conditions. The correlation of Li + –solvent coordination, solvation environments and battery performance is investigated to understand structure–property relationships.

25 ENERGY STORAGE↗
DOE OSTI2022

Capturing the swelling of solid-electrolyte interphase in lithium metal batteries

Although liquid-solid interfaces are foundational in broad areas of science, characterizing this delicate interface remains inherently difficult because of shortcomings in existing tools to access liquid and solid phases simultaneously at the nanoscale. This leads to substantial gaps in our understanding of the structure and chemistry of key interfaces in battery systems. We adopt and modify a thin film vitrification method to preserve the sensitive yet critical interfaces in batteries at native liquid electrolyte environments to enable cryo–electron microscopy and spectroscopy. We report substantial swelling of the solid-electrolyte interphase (SEI) on lithium metal anode in various electrolytes. Here, the swelling behavior is dependent on electrolyte chemistry and is highly correlated to battery performance. Higher degrees of SEI swelling tend to exhibit poor electrochemical cycling.

25 ENERGY STORAGE↗
DOE OSTI2021

Dynamic spatial progression of isolated lithium during battery operations

The increasing demand for next-generation energy storage systems necessitates the development of high-performance lithium batteries. Unfortunately, current Li anodes exhibit rapid capacity decay and a short cycle life, owing to the continuous generation of solid electrolyte interface and isolated Li (i-Li). The formation of i-Li during the nonuniform dissolution of Li dendrites leads to a substantial capacity loss in lithium batteries under most testing conditions. Because i-Li loses electrical connection with the current collector, it has been considered electrochemically inactive or ‘dead’ in batteries. In this work, contradicting this commonly accepted presumption, we show that i-Li is highly responsive to battery operations, owing to its dynamic polarization to the electric field in the electrolyte. Simultaneous Li deposition and dissolution occurs on two ends of the i-Li, leading to its spatial progression toward the cathode (anode) during charge (discharge). Revealed by our simulation results, the progression rate of i-Li is mainly affected by its length, orientation and the applied current density. Moreover, we successfully demonstrate the recovery of i-Li in Cu–Li cells with >100% Coulombic efficiency and realize LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC)–Li full cells with extended cycle life.

25 ENERGY STORAGE↗
DOE OSTI2021

Free-standing ultrathin lithium metal–graphene oxide host foils with controllable thickness for lithium batteries

Thin (≤20 μm) and free-standing Li metal foils would enable precise prelithiation of anode materials and high-energy-density Li batteries. Existing Li metal foils are too thick (typically 50 to 750 μm) or too mechanically fragile for these applications. Here, we developed a facile and scalable process for the synthesis of an ultrathin (0.5 to 20 μm), free-standing and mechanically robust Li metal foil within a graphene oxide host. In addition to low areal capacities of ~0.1 to 3.7 mAh cm –2 , this Li foil also has a much-improved mechanical strength over conventional pure Li metal foil. Our Li foil can improve the initial Coulombic efficiency of graphite (93%) and silicon (79.4%) anodes to around 100% without generating excessive Li residue, and increases the capacity of Li-ion full cells by 8%. In conclusion, the cycle life of Li metal full cells is prolonged by nine times using this thin Li composite anode.

25 ENERGY STORAGE↗
DOE OSTI2021

Dual-Solvent Li-Ion Solvation Enables High-Performance Li-Metal Batteries

Novel electrolyte designs to further enhance the lithium (Li) metal battery cyclability are highly desirable. Here, fluorinated 1,6-dimethoxyhexane (FDMH) is designed and synthesized as the solvent molecule to promote electrolyte stability with its prolonged –CF 2 – backbone. Meanwhile, 1,2-dimethoxyethane is used as a co-solvent to enable higher ionic conductivity and much reduced interfacial resistance. Combining the dual-solvent system with 1 m lithium bis(fluorosulfonyl)imide (LiFSI), high Li-metal Coulombic efficiency (99.5%) and oxidative stability (6 V) are achieved. Using this electrolyte, 20 µm Li||NMC batteries are able to retain ≈80% capacity after 250 cycles and Cu||NMC anode-free pouch cells last 120 cycles with 75% capacity retention under ≈2.1 µL mAh -1 lean electrolyte conditions. Such high performances are attributed to the anion-derived solid-electrolyte interphase, originating from the coordination of Li-ions to the highly stable FDMH and multiple anions in their solvation environments. This work demonstrates a new electrolyte design strategy that enables high-performance Li-metal batteries with multisolvent Li-ion solvation with rationally optimized molecular structure and ratio.

25 ENERGY STORAGE↗
DOE OSTI2021

Corrosion of lithium metal anodes during calendar ageing and its microscopic origins

Rechargeable lithium (Li) metal batteries must have long cycle life and calendar life (retention of capacity during storage at open circuit). Particular emphasis has been placed on prolonging the cycle life of Li metal anodes, but calendar ageing is less understood. Here, we show that Li metal loses at least 2–3% of its capacity after only 24 hours of ageing, regardless of the electrolyte chemistry. These losses of capacity during calendar ageing also shorten the cycle life of Li metal batteries. Cryogenic transmission electron microscopy shows that chemical corrosion of Li and the continuous growth of the solid electrolyte interphase—a passivation film on Li—cause the loss of capacity. Electrolytes with long cycle life do not necessarily form a solid electrolyte interphase with more resistance to chemical corrosion, so functional electrolytes must simultaneously minimize the rate of solid electrolyte interphase growth and the surface area of electrodeposited Li metal.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Efficient Lithium Metal Cycling over a Wide Range of Pressures from an Anion-Derived Solid-Electrolyte Interphase Framework

Advanced electrolytes were developed to improve the cyclability of lithium (Li) metal anodes, yet their working mechanisms remain unclear. Here, we study the Li cycling performance under different pressures in a 1 M Li bis(fluorosulfonyl)imide/fluorinated 1,4-dimethoxybutane electrolyte. A consistently long cycle life is achieved over a wide range of pressures (30–600 psi). We find that this is due to a completely different Li plating mode with more favorable deposition morphologies compared to that in a conventional carbonate electrolyte, which exhibits increasing cycle stability with increased pressure. We show that this is enabled by the properties of an anion-derived residual solid-electrolyte interphase (rSEI) framework on the electrode surface, an undercharacterized structure with profound implications for Li metal cycling. This anion-derived rSEI chemistry is likely the key to a prolonged cycle life of Li metal batteries and should be vigorously addressed in future electrolyte designs.

25 ENERGY STORAGE↗
DOE OSTI2021

Correlating Li-Ion Solvation Structures and Electrode Potential Temperature Coefficients

Temperature coefficients (TCs) for either electrochemical cell voltages or potentials of individual electrodes have been widely utilized to study the thermal safety and cathode/anode phase changes of lithium (Li)-ion batteries. However, the fundamental significance of single electrode potential TCs is little known. Here, we discover that the Li-ion desolvation process during Li deposition/intercalation is accompanied by considerable entropy change, which significantly contributes to the measured Li/Li + electrode potential TCs. To explore this phenomenon, we compare the Li/Li + electrode potential TCs in a series of electrolyte formulations, where the interaction between Li-ion and solvent molecules occurs at varying strength as a function of both solvent and anion species as well as salt concentrations. As a result, we establish correlations between electrode potential TCs and Li-ion solvation structures and further verify them by ab initio molecular dynamics simulations. We show that measurements of Li/Li + electrode potential TCs provide valuable knowledge regarding the Li-ion solvation environments and could serve as a screening tool when designing future electrolytes for Li-ion/Li metal batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Designing a Nanoscale Three-phase Electrochemical Pathway to Promote Pt-catalyzed Formaldehyde Oxidation

Gas-phase heterogeneous catalysis is a process spatially constrained on the two-dimensional surface of a solid catalyst. Here, we introduce a new toolkit to open up the third dimension. We discovered that the activity of a solid catalyst can be dramatically promoted by covering its surface with a nanoscale-thin layer of liquid electrolyte while maintaining efficient delivery of gas reactants, a strategy we call three-phase catalysis. Introducing the liquid electrolyte converts the original surface catalytic reaction into an electrochemical pathway with mass transfer facilitated by free ions in a three-dimensional space. Furthermore, we chose the oxidation of formaldehyde as a model reaction and observed a 25000-times enhancement in the turnover frequency of Pt in three-phase catalysis as compared to conventional heterogeneous catalysis. We envision three-phase catalysis as a new dimension for catalyst design and anticipate its applications in more chemical reactions from pollution control to the petrochemical industry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Organic wastewater treatment by a single-atom catalyst and electrolytically produced H2O2

The presence of organic contaminants in wastewater poses considerable risks to the health of both humans and ecosystems. Although advanced oxidation processes that rely on highly reactive radicals to destroy organic contaminants are appealing treatment options, substantial energy and chemical inputs limit their practical applications. Here we demonstrate that Cu single atoms incorporated in graphitic carbon nitride can catalytically activate H 2 O 2 to generate hydroxyl radicals at pH 7.0 without energy input, and show robust stability within a filtration device. We further design an electrolysis reactor for the on-site generation of H 2 O 2 from air, water and renewable energy. Coupling the single-atom catalytic filter and the H 2 O 2 electrolytic generator in tandem delivers a wastewater treatment system. These findings provide a promising path toward reducing the energy and chemical demands of advanced oxidation processes, as well as enabling their implementation in remote areas and isolated communities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ultralight and fire-extinguishing current collectors for high-energy and high-safety lithium-ion batteries

Inactive components and safety hazards are two critical challenges in realizing high-energy lithium-ion batteries. Metal foil current collectors with high density are typically an integrated part of lithium-ion batteries yet deliver no capacity. Meanwhile, high-energy batteries can entail increased fire safety issues. Here we report a composite current collector design that simultaneously minimizes the ‘dead weight’ within the cell and improves fire safety. An ultralight polyimide-based current collector (9 μm thick, specific mass 1.54 mg cm-2) is prepared by sandwiching a polyimide embedded with triphenyl phosphate flame retardant between two superthin Cu layers (~500 nm). Compared to lithium-ion batteries assembled with the thinnest commercial metal foil current collectors (~6 µm), batteries equipped with our composite current collectors can realize a 16-26% improvement in specific energy and rapidly self-extinguish fires under extreme conditions such as short circuits and thermal runaway.

25 ENERGY STORAGE↗
DOE OSTI2020

Revealing and Elucidating ALD-Derived Control of Lithium Plating Microstructure

The practical implementation of Li metal batteries is hindered by difficulties in controlling the Li metal plating microstructure. While previous atomic layer deposition (ALD) studies have focused on directly coating Li metal with thin films for the passivation of the electrode–electrolyte interface, a different approach is adopted, situating the ALD film beneath Li metal and directly on the copper current collector. Here, a mechanistic explanation for this simple strategy of controlling the Li metal plating microstructure using TiO 2 grown on copper foil by ALD is presented. In contrast to previous studies where ALD-grown layers act as artificial interphases, this TiO 2 layer resides at the copper–Li metal interface, acting as a nucleation layer to improve the Li metal plating morphology. Upon lithiation of TiO 2 , a Li x TiO 2 complex forms; this alloy provides a lithiophilic surface layer that enables uniform and reversible Li plating. The reversibility of lithium deposition is evident from the champion cell (5 nm TiO 2 ), which displays an average Coulombic efficiency (CE) of 96% after 150 cycles at a moderate current density of 1 mA cm –2 . This simple approach provides the first account of the mechanism of ALD-derived Li nucleation control and suggests new possibilities for future ALD-synthesized nucleation layers.

25 ENERGY STORAGE↗