Search NASA⌕ Search

Engineering topics

Wang, Hao

Publications and source records attributed to Wang, Hao.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Perovskite Catalysts for Pure-Water-Fed Anion-Exchange-Membrane Electrolyzer Anodes: Co-design of Electrically Conductive Nanoparticle Cores and Active Surfaces

Anion-exchange-membrane water electrolyzers (AEMWEs) are a possible low-capital-expense, efficient, and scalable hydrogen-production technology with inexpensive hardware, earth-abundant catalysts, and pure water. However, pure-water-fed AEMWEs remain at an early stage of development and suffer from inferior performance compared with proton-exchange-membrane water electrolyzers (PEMWEs). One challenge is to develop effective non-platinum-group-metal (non-PGM) anode catalysts and electrodes in pure-water-fed AEMWEs. We show how LaNiO3-based perovskite oxides can be tuned by cosubstitution on both A- and B-sites to simultaneously maintain high metallic electrical conductivity along with a degree of surface reconstruction to expose a stable Co-based active catalyst. The optimized perovskite, Sr0.1La0.9Co0.5Ni0.5O3, yielded pure-water AEMWEs operating at 1.97 V at 2.0 A cm-2 at 70 °C with a pure-water feed, thus illustrating the utility of the catalyst design principles.

Zhai, Tingting↗
DOE OSTI2025

Search for Solar Boosted Dark Matter Particles at the PandaX-4T Experiment

We present a novel constraint on light dark matter utilizing 1.54 metric ton/year of data acquired from the PandaX-4T dual-phase xenon time projection chamber. This constraint is derived through detecting electronic recoil signals resulting from the interaction with solar-enhanced dark matter flux. Low-mass dark matter particles, lighter than a few MeV / c 2 , can scatter with the thermal electrons in the Sun. Consequently, with higher kinetic energy, the boosted dark matter component becomes detectable via contact scattering with xenon electrons, resulting in a few keV energy deposition that exceeds the threshold of PandaX-4T. We calculate the expected recoil energy in PandaX-4T considering the Sun’s acceleration with heavy mediators and the detection capabilities of the xenon detector. The first experimental search results using the xenon detector yield the most stringent upper limits cross section of 3.51 × 10 − 39 cm 2 at 0.08 MeV / c 2 for a solar boosted dark matter mass ranging from 0.02 to 10 MeV / c 2 , achieving a 23-fold improvement compared with earlier experimental studies. Published by the American Physical Society 2025

Shen, Guofang↗
DOE OSTI2024

Regulating catalyst and ionomer interactions to promote oxygen transport in fuel cells

The cost of proton exchange membrane fuel cells (PEMFCs) has been a major impediment to their widespread commercialization. Reducing platinum (Pt) usage in PEMFC represents an essential step in lowering the cost. However, decreasing Pt loading in the cathode catalyst layer (CCL) often leads to a significant increase in the local oxygen transport resistance (R Local ), which not only slows the oxygen reduction reaction but also causes a higher polarization overpotential. The poisoning of Pt by perfluorosulfonic acid ionomers also becomes more predominant at low Pt loadings. Therefore, regulating catalyst and ionomer interactions by optimizing their interface in the CCL is crucial to improving PEMFC performance. Here, in this review, the strategies of improving oxygen transport by controlling Pt-ionomer interactions and interfaces through catalyst design, ionomer structure, and incorporation of additives are summarized. Finally, perspectives on future optimization of catalyst and ionomer interactions are proposed.

25 ENERGY STORAGE↗
DOE OSTI2024

Enhancing carbon dioxide capture under humid conditions by optimizing the pore surface structure

Metal–organic frameworks (MOFs) exhibit significant potential for mitigating carbon emissions due to their high porosity and tunability. Despite numerous reports on CO 2 capture by MOF sorbents, a common challenge is their poor selectivity for CO 2 over water. Moreover, in-depth studies are much needed to elucidate the relationships among the pore surface structure, hydrophobicity, and CO 2 uptake capacity/selectivity. In this work, we investigate the factors influencing CO 2 adsorption capacity and selectivity under humidity in a series of isoreticular pillar-layer structures, Ni 2 (L) 2 (dabco) (L = bdc, ndc, adc). Our study shows that increasing ligand conjugation not only results in increased hydrophobicity, decreased pore size and BET surface area, but also leads to the change of primary binding sites of water molecules and higher binding energy of CO 2 , all of which contribute to largely increased CO 2 uptake capacity under humid conditions. Additionally, increasing ligand conjugation and consequently hydrophobicity slow down and reduce competitive water adsorption drastically. Notably, the MOF made of ligand with the highest conjugation, Ni 2 (adc) 2 (dabco), exhibits significantly enhanced CO 2 adsorption in N 2 /CO 2 binary mixtures under relatively high humidity (50% RH), with an increase of ~31% and ~36% for the composition of 15/85 and 50/50, respectively, compared to dry conditions. An experimental FTIR study and DFT theoretical calculations confirm that H 2 O occupies different primary binding site in Ni 2 (bdc) 2 (dabco) and Ni 2 (adc) 2 (dabco), and under humid conditions a higher binding energy of CO 2 is achieved with preferential H 2 O/CO 2 co-adsorption in Ni 2 (adc) 2 (dabco), potentially creating additional adsorption sites for CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Water-induced surface ordering facilitating the microcutting of ductile metals

Metal cutting is a crucial process in modern manufacturing. Enhancing the machinability of metals can significantly improve their production efficiency and surface integrity. Coating surface-active media (SAM) on the free surface of the metals before cutting is an easy method to improve machinability, which usually pertains to the category of the renowned Rehbinder effect. However, the existing SAM is usually hazardous and complex materials. Besides, the effect of SAM on the local structure of the metal surface remains unclear. In this study, water is employed as a simple yet often overlooked SAM in the microcutting of copper. Using water as SAM also allows the employment of X-ray absorption fine structure spectroscopy (XAFS) to study the local structure of copper with and without water coating. Results show that water coating on the free surface of copper can significantly reduce the cutting force and chip thickness, and improve the surface finish. Interestingly, removing the water coating enables the recovery of the cutting force, demonstrating a reversible effect. Based on the XAFS results and molecular dynamics simulation, a water-induced surface ordering mechanism is proposed to explain the findings from the microcutting experiments. This mechanism suggests that water molecules can induce surface ordering in copper, resulting in reduced surface energy and fracture toughness of copper, thus enhancing machinability. In conclusion, this work provides valuable insights into the comprehension of the Rehbinder effect and shows that picometer-scale modifications of the surface atom arrangement can considerably alter the deformation mode of metals, paving the way for the development of new manufacturing processes.

36 MATERIALS SCIENCE↗