Synthesis and Characterization of Ternary Cobalt Spinel Oxides for Photoelectrochemical Water Splitting to Produce Hydrogen
No abstract prepared.
Engineering topics
Publications and source records attributed to Wang, Heli.
No abstract prepared.
No abstract prepared.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Abstract not provided
Explore the source record for details and available documents.
Ga–N co-doped ZnO thin films with reduced bandgaps were deposited on F-doped tin-oxide-coated glass by radio-frequency magnetron sputtering at different substrate temperatures in mixed N2 and O2 gas ambient. We found that Ga–N co-doped ZnO films exhibited enhanced crystallinity when compared to undoped ZnO films grown under the same conditions. Furthermore, Ga–N co-doping ensured enhanced N-incorporation ZnO thin films as the substrate temperature is increased. As a result, Ga–N co-doped ZnO thin films exhibited much improved photoelectrochemical (PEC) response, compared to ZnO thin films. Our results therefore suggest that the passive co-doping approach could be a means to improve PEC response for bandgap-reduced wide-bandgap oxides through impurity incorporation.
Explore the source record for details and available documents.
An austenite 349 stainless steel was nitrided via nitrogen plasma. Glancing angle X-ray diffraction patterns suggest that the nitrided layer is amorphous. X-ray photoelectron spectroscopy analysis indicated that the plasma nitridation process produced bulk-type nitrides in the surface layer. In general, the nitrided layer was composed of iron oxide in the outer layer and chromium oxide in the inner layers. Contaminations of vanadium and tin were detected in the as-grown nitrided layer; these dissolved away after polarization. The influence of these contaminants on the corrosion resistance of the nitrided layer in polymer electrolyte membrane fuel cell (PEMFC) environments is not considered significant. The nitrided sample had a much higher contact resistance than the bare one and the contact resistance increased with the nitriding time. The high interfacial contact resistance values can be related to the thicker oxide film after plasma nitridation. The corrosion resistances obtained for the 1 h nitrided and bare stainless steels in simulated PEMFC environments were similar. The outmost nitrided layer dissolved after polarization in the PEMFC environments leaving a passive film (modified with nitrides), similar to that of bare stainless steel under the same conditions. The passive film thickness was 3.7 nm for nitrided steel in PEMFC cathode environment and 4.2 nm for nitrided steel in PEMFC anode environment.
Thermal (gas) nitridation of stainless steels can yield low interfacial contact resistance (ICR), electrically-conductive and corrosion-resistant nitride containing surfaces (Cr2N, CrN, TiN, V2N, VN, etc) of interest for fuel cells, batteries, and sensors. This paper presents the results of scale up studies to determine the feasibility of extending the nitridation approach to thin 0.1 mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. A major emphasis was placed on selection of alloy foil composition and nitidation conditions potentially capable of meeting the stringent cost goals for automotive PEMFC applications. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. Promising behavior was observed under simulated aggressive anode- and cathode- side bipolar plate conditions for both materials. Variation in ICR values were observed for treated 2205 foil, with lower (better) values generally observed for the treated Fe-20Cr-4V. This behavior was linked to the nature of the pre-oxidized and nitrided surface structure, which contained through surface layer thickness V-nitride particles in the case of Fe-20Cr-4V but near continuous chromia in the case of 2205 stainless steel. The implications of these findings for stamped bipolar plate foils are discussed.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Effort devoted to scale up and demonstration of thin stamped metallic bipolar plates. Overall goal is to demonstrate potential for metallic bipolar plates to meet 5000 h automotive durability goal at a cost of less than $5/kW.