Search NASA⌕ Search

Engineering topics

Wang, Hsin

Publications and source records attributed to Wang, Hsin.

At least 91 records · Page 5

Overcharge-to-thermal-runaway behavior and safety assessment of commercial lithium-ion cells with different cathode materials: A comparison study

In this paper, overcharge behaviors and thermal runaway (TR) features of large format lithium-ion (Li-ion) cells with different cathode materials (LiFePO 4 (LFP), Li[Ni 1/3 Co 1/3 Mn 1/3 ]O 2 (NCM111), Li[Ni 0.6 Co 0.2 Mn 0.2 ]O 2 (NCM622) and Li[Ni 0.8 Co 0.1 Mn 0.1 ]O 2 (NCM811)) were investigated. The results showed that, under the same overcharge condition, the TR of LFP Li-ion cell occurred earlier compared with the NCM Li-ion cells, indicating its poor overcharge tolerance and high TR risk. However, when TR occurred, LFP Li-ion cell exhibited lower maximum temperature and mild TR response. All NCM Li-ion cells caught fire or exploded during TR, while the LFP Li-ion cell only released a large amount of smoke without fire. According to the overcharge behaviors and TR features, a safety assessment score system was proposed to evaluate the safety of the cells. In short, NCM Li-ion cells have better performance in energy density and overcharge tolerance (or low TR risk), while LFP Li-ion cell showed less severe response to overcharging (or less TR hazards). For NCM Li-ion cells, as the ratio of nickel in cathode material increases, the thermal stability of the cathode materials becomes poorer, and the TR hazards increase. Such a comparison study on large format Li-ion cells with different cathode materials can provide deeper insights into the overcharge behaviors and TR features, and provide guidance for engineers to reasonably choose battery materials in automotive applications.

25 ENERGY STORAGE↗

Microscopic analysis of copper current collectors and mechanisms of fragmentation under compressive forces

Extensive fragmentation of copper current collectors was observed after spherical indentation on prismatic and large-format pouch Li-ion cells by 3D X-ray computed tomography (XCT). Microscopic analysis including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and x-ray photoelectron microscopy (XPS) was carried out on copper current collectors from used commercial cells and pristine anodes. The copper-graphite cross-section images showed rough interface areas affected by reactions and diffusion in the used cell. Electron probe micro-analyzer (EPMA) element mapping showed the interface area was rich in oxygen and phosphorus. A detectable amount of phosphorus was also uniformly distributed inside the current collector. The same oxygen and phosphorus distributions were confirmed by STEM/EDS analysis. XPS depth profiles on multiple elements revealed the interface area of the aged anode was rich in Li, F, P, O and C and diffused at least 50 nm into the copper. In comparison, the pristine anode showed a very smooth C/Cu interface. No other elements were detected. For commercial cells, the reactions in the interface area and diffusion of multiple elements into the lattice and grain boundaries were responsible for the embrittlement of the copper current collectors. Finally, permanent cell capacity loss was observed in electrochemical performance of the indented cells.

36 MATERIALS SCIENCE↗

Determination of neutron irradiation temperatures of SiC using electrical resistivity method

The irradiation temperature of silicon carbide (SiC) was determined post-irradiation by examination of the recovery of the electrical resistivity due to thermal annealing in a rapid heating/cooling optical furnace. High-purity, high-resistivity grade SiC is routinely used as a passive temperature monitor in neutron irradiation studies at the High Flux Isotope Reactor (HFIR), and this paper presents an alternative automated technique for determination of the irradiation temperature the SiC experienced. Neutron collisions with the atoms results in displaced lattice atoms (interstitials) that act as electron donors yielding a significant decrease in electrical resistivity. The irradiation defects become thermodynamically unstable and start to recombine, when annealed above the irradiation temperature, resulting in a recovery of the electrical resistivity. The resistivity is measured at a fixed elevated temperature above ambient, which is below the target irradiation temperature. When the resistivity is plotted as a function of annealing temperatures, a clear increase is observed due to the recovery of irradiation defects. We have demonstrated that this electrical resistivity measurement of SiC is effective to determine irradiation temperature of SiC. In conclusion, energy levels of various defects in SiC were calculated from Arrhenius plots of electrical conductivity versus inverse temperature.

36 MATERIALS SCIENCE↗

Mechanical and Thermophysical Properties of 3D-Printed SiC-FY20

In the Transformational Challenge Reactor (TCR), the fuel blocks consist of an additively-manufactured silicon carbide (SiC) matrix and uranium nitride tristructural isotropic (UN TRISO) fuel particles, which are stacked to form fuel columns. The SiC matrix is manufactured using binderjet 3D printing followed by loading the TRISO fuel particles and the chemical vapor infiltration (CVI) process. Because the fuel matrix is a primary component of the TCR core and its response to mechanical and thermal loads during operation is one of the most influential factors on the integrity of TCR core, testing and evaluation have focused on producing mechanical and thermophysical properties data for the binderjet/CVI SiC. Mechanical and thermophysical properties were measured from various types of specimens printed for two or three orientations, which included equibiaxial flexural failure strength, elastic constants, thermal diffusivity and conductivity, density, and the coefficient of thermal expansion. Flexural failure strength datasets showed similar Weibull distributions regardless of sample variants including different orientations. The mean failure strengths of the 3D-printed SiC variants were in the range of 286–306 MPa, which are 22–27% lower than that of the CVD SiC. Thermophysical test results showed that specific heat and thermal expansion are not sensitive to the build directions of SiC samples, while thermal diffusivity is highly dependent on the build direction and can be correlated to the anisotropic character of the 3D-printed SiC. This report also includes discussions on the uniaxial tensile properties of the as-printed SiC before CVI and on ongoing efforts for irradiation effects studies.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Thermal Properties of the Very Low Thermal Conductivity Ternary Chalcogenide Cu 4 Bi 4 M 9 (M = S, Se)

Temperature-dependent thermal properties of phase-pure polycrystalline ternary chalcogenides Cu 4 Bi 4 S 9 and Cu 4 Bi 4 Se 9 are reported. The structure and bonding in these materials result in very low thermal conductivity values (<0.8 W m -1 K -1 at room temperature) for both materials. The lattice contribution, Debye temperatures, and Sommerfeld coefficient are obtained from low-temperature heat capacity data that also indicate very small electronic contributions to the heat capacity for these materials. This study aids in the identification of new nontoxic, earth-abundant resistive ternary chalcogenide materials with low thermal conductivity for potential thermal barrier coating and rewriteable storage applications.

36 MATERIALS SCIENCE↗

Investigation on capacity loss mechanisms of lithium-ion pouch cells under mechanical indentation conditions

Capacity loss was observed in Li-ion cells after mechanical deformation approaching the onset of internal short circuit (ISCr). In this paper, a series of indentation tests were carried out on commercial Li-ion cells of three capacities (500, 1500 and 2000 mAh). Both in-situ and ex-situ methods were used to investigate the mechanisms of indentation-induced capacity loss. We note after indentation test, the cell capacity reduced by 0.5%–6% of its original value. The incremental capacity (IC) analysis results showed that IC curves generally shifted to lower voltage region, indicating the increase in cell internal resistance. In addition, the fitting results of electrochemical impedance spectroscopy (EIS) indicated that mechanical indentation can result in a reduction in ohmic resistance and the increase in polarization resistance. Scanning electron microscopy (SEM) and X-ray computed tomography (XCT) results showed crushing of graphite, mud cracking of copper current collectors and enlarged pores in separator, which is proposed to be the main reasons for the increase in polarization resistance and permanent capacity loss. The rapid capacity loss due to mechanical abuse was compared with the long-term capacity fading.

25 ENERGY STORAGE↗

Kinetics of the functionalization of mesoporous silica nanoparticles: Implications on surface group distributions, adsorption and catalysis

The post-synthesis functionalization (grafting) kinetics of mesoporous silica nanoparticles (MSN) with organotrimethoxysilanes (R-TMS) is studied via solution 1 H NMR spectroscopy. The process involves a rapid adsorption/ desorption pre-equilibrium followed by reaction of R-TMS with surface silanols. Grafting rates are affected by the functional group in R-TMS. For example, the grafting rate of aminopropyl-trimethoxysilane (AP-TMS) is one order of magnitude higher than other R-TMS. High concentrations of AP-TMS result in substrate-inhibition kinetics, likely due to steric and mobility constraints for reactant alignment at high coverage. The higher rates of AP-TMS grafting indicate a catalytic effect of amine groups. This effect depends on the amine’s basicity and can be used to control the grafting rates and degree of condensation of other R-TMS. Adjusting the rate of mercaptopropyl-trimethoxysilane (MP-TMS) grafting using amines gives MP-MSN materials of varying adsorptive and catalytic activities, illustrated by Pd scavenging experiments and use of Pd@MP-MSN as catalysts for a Suzuki-Miyaura cross-coupling reaction.

36 MATERIALS SCIENCE↗

Fabrication of films and coatings used to activate shear thickening, impact resistant electrolytes

A method of making a passively impact resistant composite electrolyte and separator layer includes providing a suspension composition including electrically non-conducting particles that enable shear thickening. The particles can have a polydispersity index of no greater than 0.1, an average particle size in a range of from 50 nm to 1 um, and an absolute zeta potential of greater than ±40 mV. A particle suspension solvent is provided for suspending the particles. The suspension composition is applied to a porous separator material. A portion of the particles and suspension solvent penetrate the pores and the remainder of the particles in the suspension composition are distributed across the surface of the separator material. The suspension solvent is evaporated from the separator material to provide a shear thickening particle loaded separator. A separator assembly and a passivated battery are also disclosed.

25 ENERGY STORAGE↗

Toward hydrogen economy: Selective guaiacol hydrogenolysis under ambient hydrogen pressure

The conversion of guaiacol into the nylon precursors, cyclohexanol and cyclohexanone, is catalyzed by palladium supported on high surface area ceria (Pd/HS CeO 2 ) under mild conditions (100 °C, ≤1 bar H 2 ) via sequential hydrodemethoxylation and hydrogenation. In contrast, the 2-methoxycyclohexanol side product is generated by direct guaiacol hydrogenation. Reaction selectivity is determined by competing CO bond hydrogenolysis versus arene hydrogenation. Hydrogenolysis selectivity increases as H 2 pressure decreases, and over 80 % H 2 is incorporated into the products at 1 bar H 2 . Higher reactivity of guaiacol than anisole implies that the hydroxyl group is essential in Pd/HS CeO 2 catalysis. Participation of water in the conversion is evidenced by deuterium incorporation at non-exchangeable positions when the reaction is performed in D 2 O. Here, the combination of near quantitative mass balance of H 2 , high recyclability, and use of water as a solvent offers a simple, green and efficient conversion of lignin-derived aromatics into commercial products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Internal short circuit and failure mechanisms of lithium-ion pouch cells under mechanical indentation abuse conditions: An experimental study

Electromechanical structural integrity and thermal stability dictate the safety performance of lithium-ion batteries. Progressive deformation and failure across microscopic and macroscopic lengths scales that are responsible for internal short circuit (ISC) in lithium-ion cells under mechanical abuse conditions remains elusive. In this study, a series of indentation tests were conducted on lithium-ion cells with different capacities up to the occurrence of ISC. The external response and internal configuration of these cells were investigated. It is discovered that cells with different capacities and state of charges exhibited different behaviors. Maximum temperature, which is often regarded as the most important parameter related to thermal runaway (TR), varied considerably due to the complicated contact configurations. X-ray computed tomography (XCT) showed that ISC was a collective result of shear band or other strain-localization modes in the electrode assembly, shear offsets in the granular coatings of electrodes, and the accompanying ductile fracture in the metal foils. We believe that the irregular strain-localization modes (kinks, cusps, and buckles), radical mismatches in mechanical properties of different layers, and geometric features of the indenter eventually lead to the tearing/puncture of cell separator at various locations. Furthermore, the results could provide useful guidance for the micromechanical modeling of lithium-ion cells.

25 ENERGY STORAGE↗

Structural, Electronic, and Thermal Properties of CdSnAs 2

Structural, electrical, and thermal properties of CdSnAs 2 , with analyses from temperature-dependent transport properties over a large temperature range, are reported. Phase-pure microcrystalline powders were synthesized that were subsequently densified to a high-density homogeneous polycrystalline specimen for this study. Temperature-dependent transport indicates n-type semiconducting behavior with a very high and nearly temperature independent mobility over the entire measured temperature range, attributed to the very small electron effective mass of this material. The Debye model was successfully applied to model the thermal conductivity and specific heat. Furthermore, this work contributes to the fundamental understanding of this material, providing further insight and allowing for investigations into altering this and related physical properties of these materials for technological applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of Urbix Resources Natural Flake Graphite Material for Nuclear Applications (CRADA NFE-18-07340 Final Report)

Urbix Resources is a company specializing in graphite powder processing and purification. Urbix is looking to become the first domestic supplier of nuclear-grade graphite in the United States. This has led to a Cooperative Research and Development Agreement (CRADA) being established between the Oak Ridge National Laboratory (ORNL) and Urbix Resources, with the goal of characterizing a purified graphite feedstock supplied by Urbix Resources. The resulting data will then be used to determine the viability of a large-scale nuclear graphite production and qualification campaign. These characterization methods have been performed on the as-received graphite feedstock, a heat-treated batch of the feedstock, a milled batch of the feedstock, and a nuclear-grade graphite powder historically used in fuel production. The data from the heat-treated and milled feedstock will determine how different processing methods affect the powder’s physical properties, whereas the data from the nuclear grade graphite will provide information about the characteristics of a graphite previously accepted for nuclear applications. All of these powders have been characterized individually and as part of a resin-graphite blend (herein referred to as matrix) that has been used in past fuel experiments. The results of these experiments show that the Urbix powder and nuclear-grade graphite powder display notably different properties from one another in many cases, but this discrepancy may have been the result of the typical particle size of each powder. This hypothesis is supported by tests conducted on the milled powder, which showed a closer resemblance in properties to the nuclear-grade graphite than the as-received powder. The method for pressing the graphite matrix also had a noticeable effect on the measured properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synthesis, transport properties and electronic structure of p-type Cu 1+x Mn 2–x InTe 4 ( x = 0, 0.2, 0.3)

The synthesis, electronic structure and temperature dependent transport properties of polycrystalline Cu 1+x Mn 2–x InTe 4 (x = 0, 0.2, 0.3) are reported for the first time. These quaternary chalcogenides were synthesized by direct reaction of the elements, followed by solid state annealing and hot press densification. The thermal conductivity is low for all specimens and intrinsic to the material system. Furthermore, the off-stoichiometry specimens illustrate the sensitivity of the transport properties to stoichiometry, with a greater than two-orders-of magnitude increase in carrier concentration with increased Cu content. First principles calculations of the electronic structure are also reported, and are in agreement with the experimental data. Here, this fundamental investigation shows the potential towards further optimization of the electrical properties that, in addition to the intrinsically low thermal conductivity, provides a basis for further research into the viability of this material system for potential energy-related applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Binder jet printed WC infiltrated with pre-made melt of WC and Co

WC-Co was made via binder jet additive manufacturing of tungsten carbide followed by melt infiltration with a Co-WC infiltrant. The goal of the study was to achieve fully densified parts in near-net shape with minimal shrinkage while keeping the Co content low. The exact amount of infiltrant was determined in order to fully densify with minimum shrinkage based on the actual volume taken up by WC powder in the preform based on theoretical density, the bounding volume of prints after shrinkage, and the volume from the infiltrant. The eutectic nature of the infiltrant enabled melting at much lower temperature compared to the melting temperature of pure Co. The density, microstructure, grain size, hardness, and fracture toughness were characterized. The shrinkage and net shaping were assessed with light scans. A detailed look at the fracture mechanics was assessed. Here, this approach achieved highly dense WC-Co parts in net-shape with Co vol% of near 29 (Co wt% ~19), density of 96.2% theoretical, hardness of 8.34 GPa, grain size of 7.7 μm, magnetic saturation of 0.5 T, room temperature thermal conductivity of 125 W/mK, and fracture toughness of 24.7 = MPa·m 1/2 .

36 MATERIALS SCIENCE↗

Micromechanical and microstructure analysis of strain-induced phenomena in ultrasonic additively-manufactured Al-6061 alloy

This work investigates the anisotropic mechanical behavior (both macro and micro) of Al6061 alloy samples manufactured using ultrasonic additive manufacturing. Samples from both sonotrode travel and vibration directions (TD and VD, respectively) were investigated in the as-built and aged (8 h at 180 °C under Argon gas) conditions. The aged VD-specimens showed appearance and propagation of Luders-like band, which did not exist in the TD-specimens, deformed at the same strain rate. X-ray diffraction, x-ray computed tomography, scanning electron microscopy, laser flash technique and in-situ loading with neutron diffraction were used to characterize the material and its hardening behavior during straining. Furthermore, aging was mainly found to lead to relaxation of stresses, induced by the build process, some decrease in yield stress, and potential secondary phase reprecipitation. Stress partitioning, revealed via in situ neutron diffraction, showed that one of grain families, (110) || tensile axis, revealed strain softening at small strain range. This texture component, (110) || tensile axis, dominated the structure of VD-specimens, and was one of key factors stimulating band appearance and propagation.

36 MATERIALS SCIENCE↗

Fundamental Science and Technology of Flash Processing Robustness for Advanced High Strength Steels (AHSS)

“Flash processed” low carbon steel sheets were characterized using in-situ IR imaging, ex-situ dome deformation testing and microscopy. Due to flash processing set-up, cooling water flow and steam interfered with robust infrared temperature measurements. Though preliminary, rapidly heating the steel sheet to greater than 1170°C and then water quenching a few seconds later can result in through thickness microstructural gradients, where the center is harder than the exterior surfaces. This microstructural configuration sometimes results in a dome displacement ~75% relative to that observed in the more ductile as-received material. The presence of aluminum nitride (AlN) inclusions was confirmed, a likely byproduct from a de-oxidization reaction, and may reduce dome displacement (similar to strain to failure) significantly. Based on thermodynamic calculations, a high flash processing temperature (>1170°C) is recommended to dissolve these AlN inclusions in the austenite phase.

36 MATERIALS SCIENCE↗