Search NASA⌕ Search

Engineering topics

Wang, Huiping

Publications and source records attributed to Wang, Huiping.

Activation of Transition Metal (Fe, Co and Ni)-Oxide Nanoclusters by Nitrogen Defects in Carbon Nanotube for Selective CO 2 Reduction Reaction

The electrochemical carbon dioxide reduction reaction (CO2RR), which can produce value-added chemical feedstocks, is a proton-coupled-electron process with sluggish kinetics. Thus, highly efficient, cheap catalysts are urgently required. Transition metal oxides such as CoO x , FeO x , and NiO x are low-cost, low toxicity, and abundant materials for a wide range of electrochemical reactions, but are almost inert for CO 2 RR. Here, we report for the first time that nitrogen doped carbon nanotubes (N-CNT) have a surprising activation effect on the activity and selectivity of transition metal-oxide (MO x where M = Fe, Ni, and Co) nanoclusters for CO 2 RR. MO x supported on N-CNT, MOx/N-CNT, achieves a CO yield of 2.6–2.8 mmol cm -2 min -1 at an overpotential of -0.55V, which is two orders of magnitude higher than MO x supported on acid treated CNTs (MOx/O-CNT) and four times higher than pristine N-CNT. The faraday efficiency for electrochemical CO 2 -to-CO conversion is as high as 90.3% at overpotential of 0.44V. Both in-situ XAS measurements and DFT calculations disclose that MO x nanoclusters can be hydrated in CO 2 saturated KHCO 3 , and the N defects of N-CNT effectively stabilize these metal hydroxyl species under carbon dioxide reduction reaction conditions, which can split the water molecules and provide local protons to inhibit the poisoning of active sites under carbon dioxide reduction reaction conditions.

36 MATERIALS SCIENCE↗

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗

Zn/ZnO dendrites arising the heat-treatment of Zn dendrites and their photocatalytic reduction of Cr(VI)

Highlights: • Zn/ZnO dendrites are prepared by an electrodeposition and subsequent annealing route. • The annealing temperature strongly affects the molar ratio of Zn/ZnO in the product. • As-prepared products can be used as the photocatalysts for the reduction of Cr(VI). • Zn/ZnO-200 presents the strongest photocatalytic activity for the reduction of Cr(VI). - Abstract: An electrodeposition-calcination route was designed for the preparation of Zn/ZnO dendrites in this work. Zn dendrites were first deposited at room temperature via a potentiostatic electrodeposition route at the potential of −1.5 V for 10 min. Then, Zn/ZnO dendrites were obtained through calcining Zn dendrites in air at 100–400 °C for 30 min. The produced Zn/ZnO dendrites were labeled as Zn/ZnO-N (N = 100, 200, 300 and 400). The investigations showed that the as-obtained Zn/ZnO-200 dendrites exhibited the strongest photocatalytic activity for the reduction of Cr (VI)–Cr (III) under the radiation of 460 mW cm{sup −2} white light from a Xenon lamp. Within 16 min, ∼92% of Cr (VI) was reduced when Zn/ZnO-200 was used as the photocatalyst. Also, the as-obtained Zn/ZnO-200 catalyst owned good stability. After six cycles, the catalytic efficiency had only slight decrease, which is favorable for reducing the cost in the practical application.

36 MATERIALS SCIENCE↗

Prediction of residual stresses in a multipass pipe weld by a novel 3D finite element approach

Due to enormous computation cost, current residual stress simulation of multipass girth welds are mostly performed using two-dimensional (2D) axisymmetric models. The 2D model can only provide limited estimation on the residual stresses by assuming its axisymmetric distribution. In this study, a highly efficient thermal-mechanical finite element code for three-dimensional (3D) model has been developed based on high performance Graphics Processing Unit (GPU) computers. Our code is further accelerated by considering the unique physics associated with welding processes that are characterized by steep temperature gradient and a moving arc heat source. It is capable of modeling large-scale welding problems that cannot be easily handled by the existing commercial simulation tools. To demonstrate the accuracy and efficiency, our code was compared with a commercial software by simulating a 3D multi-pass girth weld model with over 1 million elements. Our code achieved comparable solution accuracy with respect to the commercial one but with over 100 times saving on computational cost. Moreover, the three-dimensional analysis demonstrated more realistic stress distribution that is not axisymmetric in hoop direction.

Huang, Hui↗

STRESS AND DISTORTION SIMULATION OF ADDITIVE MANUFACTURING PROCESS BY HIGH PERFORMANCE COMPUTING

Numerical simulation is an efficient way to better understand the thermal and mechanical evolution during additive manufacturing (AM) and to design and optimize the process. However, with today’s computational tools, pass-by-pass thermal-mechanical numerical simulation of the AM process is extremely time-consuming. In this study, a new finite element code recently developed in house at Oak Ridge National Lab was used for additive manufacturing simulation. Our new code effectively utilizes GPU based high-performance computers to allow for realistic simulation of the transient thermal and mechanical response of materials during additive manufacturing. A benchmark study on a cylinder model by powder bed selective laser melting was carried out and distortion profile was compared to the experimental measurements. The accuracy and efficiency of the code was also demonstrated by analyzing a wire and arc additive manufacturing (WAAM) model which consists of a base plate and four deposited layers.

Huang, Hui↗