Search NASA⌕ Search

Engineering topics

Wang, Junpeng

Publications and source records attributed to Wang, Junpeng.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Chemically and Mechanically Recyclable Vitrimers from Carbon Dioxide-Based Polycarbonates

Designing thermoset materials with dynamic crosslinks is an important strategy to mitigate rising global carbon dioxide emission levels. The development of polymers from sustainable feedstocks, with efficient manufacturing methods, for high-value applications, and with circular end-of-use solutions is essential for advancing material technologies. One approach involves exploiting carbon dioxide itself as feedstock to create high performance, sustainable materials, by enchaining 50 mol% CO2 via copolymerization with epoxides to yield polycarbonates. This work describes the synthesis, end-functionalization, and curing of poly(propylene carbonate) (PPC) and poly(cyclohexene carbonate) (PCHC) into beta-hydroxy ester vitrimers. These vitrimers demonstrate the ability to be mechanically reprocessed up to 3 times with retention of the material’s properties through dynamic transesterification exchange reactions. The polycarbonate vitrimers with gel fractions exceeding 90 % exhibit high tensile strength (> 50 MPa) and Young’s modulus (> 2 GPa), achieved by varying repeat unit structure in the polymer backbone from the low Tg PPC to the more rigid high Tg PCHC structures. Owing to an entropically favorable chain back-biting mechanism, the network chains can be cleaved and depolymerized into cyclic small molecules. In the case of PCHC, this process enables repolymerization back to polycarbonates with 69 wt.% CO2 retention through life-cycles. The promising mechanical performance and recyclability of these CO2-based polycarbonate vitrimers indicate their potential for sustainable, high-performance materials, paving the way for future innovations in circular polymer technologies and carbon capture utilization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Utah FORGE 5-2419: Seismicity-Permeability Relationships Probed via Nonlinear Acoustic Imaging - 2024 Annual Workshop Presentation

This is a presentation on Seismicity-Permeability Relationships Probed via Nonlinear Acoustic Imaging by Pennsylvania State University, presented by Derek Elsworth. This video slide presentation discussed controls and acoustic signatures of aseismic through seismic evolution of relocation-stability-permeability on fractures in shear-reactivation as a precursor to, and a key predictor of, seismic moment magnitude of prospective triggered-seismicity. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 13, 2024.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Utah FORGE: Fluid Injection Induced Shearing Experiments on Fractured Granitoid at Elevated Temperatures

This repository contains experimental data from a series of fluid injection-induced shearing tests conducted on Utah FORGE granitoid. The experiments were performed using an aluminum triaxial pressure vessel (TEMCO) apparatus at Pennsylvania State University. The primary aim was to investigate the impact of temperature on fault seismicity and to explore how different pre-stress ratios influence shearing behavior. The data includes results from experiments conducted under varying conditions of temperature, pre-stress ratios, and pore pressure increments. The rock samples used in these experiments were 60-grit granitoid with a single inclined fracture oriented at 60 degrees with respect to the horizontal cross-section. The dataset also includes measurements of normal stiffness at different temperatures and images of the experimental apparatus. The included README file details each experiential setup and outlines which data files represent which experimental conditions.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Utah FORGE: Temperature-Dependent Fracture Seismicity from Fluid Injection Experiments

This dataset contains experimental data from fluid injection experiments conducted to investigate the influence of temperature on fracture seismicity. The experiments were performed on granite samples from Utah FORGE. The samples were prepared with a 30-degree inclined fracture and subjected to controlled stress and temperature conditions. Data were collected under three distinct temperature settings: 24 C, 78 C, and 137 C. During the experiments, a constant confining pressure of 10 MPa and a constant shear stress at 80% of the shear strength of the sample were maintained. Pore pressure was incrementally increased at a rate of 300 kPa every three minutes to simulate fluid injection. Temperature was raised rapidly and then stabilized for the duration of each test. The dataset includes shear stress and displacement measurements under each temperature condition, along with supplementary figures illustrating the experimental setup and time-series plots of pressures and temperature.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Utah FORGE: Fault Shear Reactivation Experimental Data for Fluid Injection-Rate Controls on Seismic Moment

Included are experimental data recorded from shear experiments that specifically explore the link between fluid-injection rate and seismic moment resulting from shear reactivation of laboratory faults. Raw mechanical data from three experiments are included alongside corresponding MATLAB scripts that import and plot the data, as well as use it to calculate shear and normal stress. Experiments are performed on 2.5-3 inch long granitoid cores from the Utah FORGE EGS demonstration site, containing a single inclined fracture with small-scale roughness added to the fracture surface. The raw data included here were recorded from an aluminum triaxial pressure vessel (TEMCO) configured with three independent servo-controlled pumps, with distilled water used as the working fluid. The pumps control confining pressure, upstream pore pressure, and axial pressure, with each pump connected to a LabView interface to record applied pressures, cumulative injected water volumes, and pump flow rates. The downstream outlet from the fracture is closed to allow pressurization, which is measured by an external pressure transducer. A linear variable differential transformer (LVDT) attached to the axial piston measures axial displacement, from which we calculate shear displacement along the fracture. Additionally, P-wave transducers are used to record acoustic signatures, where acoustic emission events and maximum amplitudes are compared against seismic moment and shear slip velocity. Fluid injection rates range between 0.05 mL/min, 0.25 mL/min, and 0.75 mL/min for each experiment. Along-fault pressure distributions are progressively less uniform as injection rates increase, representing a switch from steady-state to transient conditions. Triggered shear displacement is used as a proxy for seismic moment and is indexed against cumulative injection volume and rate. Each experiment is performed under constant shear stress conditions, and the sample is fully saturated with DI water. Axial and confining stresses are applied to 3 MPa through pressure-stepping in 500 kPa increments. The pore pressure is held constant at 200 kPa prior to initiating the experiment, and initial axial displacement is recorded. The axial stress is then increased to initiate shear mobilization during the loading phase (run-in) until a peak steady state is achieved. The initial shear stress is reduced to approximately 80% of the peak shear stress by decreasing the axial stress, then held constant for the duration of each experiment.

15 GEOTHERMAL ENERGY↗