Active Material Interfacial Chemistry and Its Impact on Composite Magnetite Electrodes
Not provided.
Chemistry↗
Engineering topics
Wang, Lei
Publications and source records attributed to Wang, Lei.
Propagation of Cryogenic Thermal Fractures from Unconfined PMMA Boreholes
In cryogenic fracturing, a rock surface exposed to cryogenic fluids undergoes a large thermal gradient, and the resultant local tensile stress overcomes rock strength and initiates fractures. This study investigates the development of cracks generated from the cryogenic treatment of a borehole under no external confining stress on specimens. The experiments were performed on transparent PMMA specimens to observe fracture proliferation around boreholes. Liquid nitrogen was flowed through the boreholes to cool the borehole surface. The results show that initial fracture growth is characterized by abrupt starts and stops, and as the fracture propagates outward, the growth appears more continuous. In an early stage, horizontal/radial fractures and vertical fractures are the defining patterns. Horizontal fractures tend to be separated by a specific exclusion distance (i.e., spacing between cracks). While distinct horizontal/vertical fractures and exclusion distance manifest themselves at an early stage, fractures resulting from fracture interactions and curvatures can develop into complex shapes at later stages. Cryogenic thermal loading induces distinctively curved fractures. The tendency of curvature may prevent greater penetration. An increase in the borehole pressure during liquid nitrogen flow, however, can lessen fracture tortuosity and facilitate radial propagation. A high flow pressure and rate are also advantageous in that they accelerate cooling and fracture propagation.
42 ENGINEERING↗
Multiple Metrics Informed Projections of Future Precipitation in China
Predicting how regional precipitation will respond to future warming is among the most challenging undertaking in climate change projection. Despite sustained efforts to improve modeling and understanding of precipitation, the overall uncertainty in projecting regional precipitation has not been reduced substantially. In this work, the potential for more robust precipitation projections is demonstrated through the use of discriminating metrics to subsample the multimodel ensemble. Using a two-dimensional metric of precipitation and its relationship with large-scale circulation indices in East Asia, 31 models in the Coupled Model Intercomparison Project Phase 5 (CMIP5) are classified into three groups. Models in the top performing group projected statistically significant increasing trends in precipitation and the regional precipitation patterns are more similar to each other than to the patterns in the bottom performing group. In contrast, models in the bottom performing group projected diverse responses, with overall small drying or no significant trends in precipitation.
54 ENVIRONMENTAL SCIENCES↗
Electrolyte-Guided Design of Electroreductive CO Coupling on Copper Surfaces
Engineering the interfacial distribution of electrolytic ions can aid in modulating the electrocatalyst performance and efficiency. Using a hybrid quantum-classical modeling approach, we describe how predictive tuning of the solution microenvironment on copper can enhance the efficiency of CO 2 reduction (CO 2 R) to C 2 products. We elucidate how competing electrolyte constituents in mixed electrolyte solutions stimulate restructuring of the electrochemical double layer (EDL) and stabilize the OCCO* dimer (* denotes surface adsorbed), with predictions validated in flow reactors using copper gas diffusion electrodes (Cu-GDEs). Furthermore, our findings highlight how molecular-scale electrolyte engineering with informed models of the EDL can be leveraged to tailor CO 2 R activity and selectivity toward C 2 products.
36 MATERIALS SCIENCE↗
Molecular basis for lipid recognition by the prostaglandin D 2 receptor CRTH2
Significance Many amphipathic lipids, including cannabinoids, lysophospholipids, prostanoids, and leukotrienes, bind to G protein–coupled receptors (GPCRs) through the lipid bilayer. How these lipid ligands get anchored to their receptors and enter ligand-binding pockets is largely elusive. Our results revealed a distinctive lipid recognition mechanism for the prostaglandin D 2 (PGD 2 ) receptor CRTH2 that is not shared by other prostanoid receptors. Based on the structural analysis, we propose two representative binding modes of lipids in GPCRs. We also identified critical structural motifs and conformational changes of CRTH2 for capturing lipids from the lipidic environment and lipid transition to the binding pocket, thereby offering unprecedented molecular insight into the dynamic lipid-binding processes for GPCRs.
59 BASIC BIOLOGICAL SCIENCES↗
“Flower-like” Li 4 Ti 5 O 12 -multiwalled carbon nanotube composite structures with performance as highrate anode-materials for li-ion battery applications and methods of synthesis thereof
A method of fabricating nanocomposite anode material embodying a lithium titanate (LTO)-multi-walled carbon nanotube (MWNT) composite intended for use in a lithium-ion battery includes providing multi-walled carbon nanotube (MWNTs), including nanotube surfaces, onto which functional oxygenated carboxylic acid moieties are arranged, generating 3D flower-like, lithium titanate (LTO) microspheres, including thin nanosheets and anchoring the acid-functionalized MWNTs onto surfaces of the 3D LTO microspheres by π-π interaction strategy to realize the nanocomposite anode material.
25 ENERGY STORAGE↗
On the use of limestone calcined clay cement (LC3) in high-strength strain-hardening cement-based composites (HS-SHCC)
Highlights: • Use of LC{sup 3} slightly reduces flowability and shortens the setting time of fresh matrices. • Highly polymerized C-A-S-H gel and abundant ettringite benefit flexural strength of LC{sup 3}-matrices. • Use of LC{sup 3} enhances the bond strength between fiber and high-strength matrix. • LC{sup 3}-based HS-SHCC yields similar flexural performance as the composite with Portland cement. High-strength strain-hardening cement-based composites (HS-SHCC) demonstrate excellent mechanical and durability properties. However, high cement content typical to HS-SHCC results not only in high carbon footprint, but also in excessive hydration heat and severe autogenous shrinkage. In this investigation, Limestone Calcined Clay Cement (LC{sup 3}) was used to produce sustainable HS-SHCC. The LC{sup 3} substitution resulted in higher energy consumption during mixing and in shorter setting times of the fresh, plain matrices. Although the LC{sup 3} substitution slightly reduced the compressive strength, the formation of highly polymerized C-A-S-H gel and abundant ettringite benefited the flexural strength of the plain matrices. Additionally, single-fiber pullout experiments showed that the use of LC{sup 3} led to increased fiber-matrix bond strength and pullout energy. Finally, the replacement of Portland cement by LC{sup 3} resulted in HS-SHCC with similar mechanical performance to the reference composite, indicating a high potential for using LC{sup 3} in high-performance cement-based composites.
36 MATERIALS SCIENCE↗
High Throughput In-Line Coating Metrology Development for Solid Oxide Fuel Cell Manufacturing
Coatings play key roles in solid oxide fuel cell (SOFC) stack durability. For example, diffusion barrier coatings on Cr-containing interconnect and balance of plant (BOP) components protect electrodes from Cr poisoning over the long operational lifetimes (>10,000 hours) of the fuel cell stack. Common defects in coatings, such as cracks, pinholes, and porosity, result in a failure to protect the electrodes, resulting in shorter operational lifetime and thus higher cost. It is very unlikely, even in the best coating process, that all these defects can be mitigated, hence identifying critical defects in parts, and removing defective parts from production before they can damage the stack, becomes paramount. Furthermore, these quality control techniques must be operational in the production/assembly line (in-line), i.e., high throughput and non-destructive, and cost effective. Redox Power Systems, LLC (Redox) together with the National Renewable Energy Laboratory (NREL) developed much needed high throughput, in-line metrology techniques for protective coatings. The overall goal of the project is to lower cost while increasing robustness, reliability, and endurance of SOFC stacks. To accomplish this, we had several objectives, including: to identify key coating and substrate defects that lead to coating failure through the use of detailed characterization methods (e.g., microscopy, XRD, EDS, electrochemistry); to assess capabilities of in-line metrology techniques, e.g., optical profilometry (Redox) and thermography (NREL), to probe these defects, or evidence thereof; demonstrate long-term performance of “defect-free” protective coatings, as identified by in-line metrology, in solid oxide fuel cell (SOFC) stack operation. In the first part of this project, the ability to identify key defects expected to lead to coating and SOFC degradation using in-line metrology tools were evaluated. Coated interconnect samples with controlled defect types and populations were tested under conditions similar to SOFC operation, followed by detailed post-test analysis to reveal the defects responsible for observed degradation. In the second part of the project, the optimal in-line metrology techniques and methodologies were used to map the defect distribution in full-size interconnects with critical defects intentionally allowed to exist in some cases. These interconnects underwent SOFC testing for extended periods (up to ~3,000 hours) followed by post-test analysis to evaluate the effectiveness of in-line metrology techniques in mitigating MCO coating related degradation. Key accomplishments in this project included the following: Demonstrated ASR of < 0.05 ohm-cm 2 at 650 °C for 1,000 hours with low defect (determined by in-line metrology) interconnect samples (average ASR=37 milliohms-cm 2 after over 1,000 hours). Demonstrated that low defect coatings on interconnects (as screened using in-line metrology) have low volatilization of chromium at ~650 °C for 1,000 hours as detected using Cr-getter material (< 5 at% increase above baseline); 1022 hour duration tests under humidified, elevated temperature (750 °C rather than 650 °C) compared a base case against different coating thicknesses. Demonstrated capability to identify initial key defects of interest with in-line metrology techniques using up to 8 cm by 10 cm having coatings with and without intentional defects of interest using thermal imaging and optical profilometry. Correlated key defects identified using metrology techniques with observed coating performance (e.g., ASR and Cr volatility). Conducted several 4 cm by 4 cm cell tests using MCO-interconnects that were pre-screened using some of the metrology techniques developed in the project (e.g., optical profilometry). An analysis of ASR measurements were able to show that defect-free coatings resulted in the anticipated performance in the cell tests.
01 COAL, LIGNITE, AND PEAT↗
Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc-Ion Batteries in Water-in-Salt Electrolyte
A layered MoO 3 material with large interlayer spacing represents a promising cathode for aqueous rechargeable Zn-ion batteries (ARZIBs), but the implementation of this material is limited due to the intrinsically low conductivity and poor structural stability. A 30 m ZnCl 2 water-in-salt electrolyte (WISE) was introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 M ZnSO 4 and 3 M ZnCl2 electrolyte. The Zn/MoO 3 cell in WISE unambiguously demonstrated significantly improved rate performance delivering 349, 253, and 222 mAh/g at 100, 500, and 1000 mA/g, denoting a 2×, and 12× capacity increase of those achieved in 3 M electrolytes at 500 and 1000 mA/g, respectively. A capacity retention rate of 73% was achieved after (dis)charging at 100 mA/g for 100 cycles, and no obvious capacity fading was observed at higher current densities of 500 mA/g and 2A/g. A compilation of structural and morphological characterization was systematically performed to provide insight into the mechanisms of the improved performance in ZnCl 2 WISE for the MoO3 cathode materials. Specifically, our data collectively suggested that the drastic fading in 3M electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction (HER), which were significantly suppressed in the ZnCl 2 WISE. The direct visualization of these side reactions was achieved for the first time in the Zn-MoO 3 system, using an in situ optoelectrochemical measurement.
25 ENERGY STORAGE↗
Amorphization resistance of nanocrystalline 3C-SiC implanted with H2+ ions
Compared to single-crystal SiC, nanocrystalline SiC with high densities of stacking faults has been reported to be much more resistant to amorphization under self-ion and electron irradiations. This study examines H2+ ion irradiation-induced amorphization in nanocrystalline 3C-SiC with dense stacking faults using transmission electron microscopy. The results show that full amorphization at room temperature occurs at a comparable dose to that for its single-crystal SiC counterpart under the identical irradiation conditions. Both materials are amorphized as a result of local damage accumulation. The formation of the nucleation sites for amorphization is not appreciably affected by the presence of stacking faults and grain boundaries. The behavior may be attributed to the significant chemical effects that may completely immobilize the point defects in SiC at room temperature. The results suggest cautions be excised to use nanocrystalline SiC materials in high H irradiation environment at room temperature. Further studies of the H behavior at elevated temperatures are warranted.
Amorphization, ion irradiation, SiC↗
Impact of sodium vanadium oxide (NaV 3 O 8 , NVO) material synthesis conditions on charge storage mechanism in Zn-ion aqueous batteries
The electrochemical charge storage of sodium vanadate (NaV 3 O 8 or NVO) cathodes in aqueous Zn-ion batteries has been hypothesized to be influenced by the inclusion of structural water for facilitating ion transfer in the material. Materials properties considered important (morphology, crystallite and particle size, surface area) are systematically studied herein through investigation of two NVO materials, NaV 3 O 8 ·0.34H 2 O [NVO(300)] and NaV 3 O 8 ·0.05H 2 O [NVO(500)], with different water content, acicular morphologies with different size and surface area achieved via post-synthesis heat treatment. The electrochemistry of the two materials was evaluated in aqueous Zn-ion cells with 2 M ZnSO 4 electrolyte using cyclic voltammetry, galvanostatic cycling, and rate capability testing. Furthermore, the thinner NVO(300) nanobelts (0.13 μm) demonstrate greater specific capacities and higher effective diffusion coefficients relative to the thicker NVO(500) nanorods. Notably however, while cells containing NVO(500) deliver lower specific capacity, they demonstrate enhanced capacity retention with cycling. The structural changes accompanying oxidation and reduction are elucidated via ex situ X-ray diffraction, transmission electron microscopy, and operando V K-edge X-ray absorption spectroscopy (XAS), where NVO material properties are shown to influence the ion insertion. Operando XAS verified that electron transfer corresponds directly to change in vanadium oxidation state, affirming vanadium redox as the governing electrochemical process.
25 ENERGY STORAGE↗
3D Artificial Solid-Electrolyte Interphase for Lithium Metal Anodes Enabled by Insulator–Metal–Insulator Layered Heterostructures
Despite considerable efforts to prevent lithium (Li) dendrite growth, stable cycling of Li metal anodes with various structures remains extremely difficult due to the direct contact of the liquid electrolyte with Li. Rational design of solid-electrolyte interphase (SEI) for 3D electrodes is a promising but still challenging strategy for preventing Li dendrite growth and avoiding lithium–electrolyte side reactions in Li-metal batteries. Here, a 3D architecture is constructed with g-C 3 N 4 /graphene/g-C 3 N 4 insulator–metal–insulator sandwiched nanosheets to guide uniform Li plating/stripping in the van der Waals gap between the graphene and the g-C 3 N 4 , and the function of which can be regarded as a 3D artificial SEI. Li deposition on the surface of g-C 3 N 4 is suppressed due to its insulating nature. However, its uniform lithiophilic sites and nanopore channels enable homogeneous lithium plating between the graphene and the g-C 3 N 4 , prohibiting the direct contact of the electrolyte with the Li metal. The use of the g-C 3 N 4 -layer-modified 3D anode enables long-term Li deposition with a high Coulombic efficiency and stable cycling of full cells under high cathode loading, limited Li excess, and lean electrolyte conditions. The concept of a 3D artificial SEI will shed light on developing safe and stable Li-metal anodes.
25 ENERGY STORAGE↗
Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc‐Ion Batteries in Water‐in‐Salt Electrolyte
Abstract Layered MoO 3 represents a promising cathode for aqueous rechargeable Zn‐ion batteries, but the implementation of this material is limited due to the low conductivity and poor structural stability. A 30 m ZnCl 2 water‐in‐salt electrolyte (WISE) is introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 m ZnSO 4 and 3 m ZnCl 2 . The Zn/MoO 3 cell in WISE unambiguously demonstrate significantly improved rate performance delivering 349, 253, and 222 mAh g −1 at 100, 500, and 1000 mA g −1 , denoting a 12× capacity increase of those achieved in 3 m electrolytes at 1000 mA g −1 . A capacity retention rate of 73% is achieved after (dis)charging at 100 mA g −1 for 100 cycles, and no obvious capacity fading is observed at higher current densities of 500 mA g −1 and 2 A g −1 . Specifically, the data suggest that the drastic fading in 3 m electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction, which are significantly suppressed in the WISE. The direct visualization of these side reactions is achieved for the first time in the Zn‐MoO 3 system, using an in situ optoelectrochemical measurement.
Wang, Lei↗
Moiréless correlations in ABCA graphene
Atomically thin van der Waals materials stacked with an interlayer twist have proven to be an excellent platform toward achieving gate-tunable correlated phenomena linked to the formation of flat electronic bands. In this work we demonstrate the formation of emergent correlated phases in multilayer rhombohedral graphene––a simple material that also exhibits a flat electronic band edge but without the need of having a moiré superlattice induced by twisted van der Waals layers. We show that two layers of bilayer graphene that are twisted by an arbitrary tiny angle host large (micrometer-scale) regions of uniform rhombohedral four-layer (ABCA) graphene that can be independently studied. Scanning tunneling spectroscopy reveals that ABCA graphene hosts an unprecedentedly sharp van Hove singularity of 3–5-meV half-width. We demonstrate that when this van Hove singularity straddles the Fermi level, a correlated many-body gap emerges with peak-to-peak value of 9.5 meV at charge neutrality. Mean-field theoretical calculations for model with short-ranged interactions indicate that two primary candidates for the appearance of this broken symmetry state are a charge-transfer excitonic insulator and a ferrimagnet. Finally, we show that ABCA graphene hosts surface topological helical edge states at natural interfaces with ABAB graphene which can be turned on and off with gate voltage, implying that small-angle twisted double-bilayer graphene is an ideal programmable topological quantum material.
42 ENGINEERING↗
Self-Healing, Improved Efficiency Solid State Rechargeable Li/I 2 Based Battery
Solid state electrolytes are receiving significant interest due to the prospect of improved safety, however, addressing the incidence and consequence of internal short circuits remains an important issue. In this study, a battery based on a LiI-LiI(HPN) 2 solid state electrolyte demonstrated self-healing after internal shorting where the cells recovered and continued to cycle effectively. The functional rechargeable electrochemistry of the self-forming Li/I 2 -based battery was investigated through interfacial modification by inclusion of Li metal (at the negative interface), and/or fabricated carbon nanotube substrates at the positive interface. A cell design with lithium metal at the negative and a carbon substrate at the positive interface produced Coulombic efficiencies > 90% over 60 cycles. Finally, the beneficial effects of moderately elevated temperature were established where a 10 °C temperature increase led to ~5× lower resistance.
25 ENERGY STORAGE↗