Search NASA⌕ Search

Engineering topics

Wang, Siheng

Publications and source records attributed to Wang, Siheng.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Phase Transitions and Thermal Equation of State of Fe‐9wt.%Si Applied to the Moon and Mercury

Abstract Accurate knowledge of the phase transitions and thermoelastic properties of candidate iron alloys, such as Fe‐Si alloys, is essential for understanding the nature and dynamics of planetary cores. The phase diagrams of some Fe‐Si alloys between 1 atm and 16 GPa have been back‐extrapolated from higher pressures, but the resulting phase diagram of Fe 83.6 Si 16.4 (9 wt.% Si) is inconsistent with temperature‐induced changes in its electrical resistivity between 6 and 8 GPa. This study reports in situ synchrotron X‐ray diffraction (XRD) measurements on pre‐melted and powder Fe 83.6 Si 16.4 samples from ambient conditions to 60 GPa and 900 K using an externally heated diamond‐anvil cell. Upon compression at 300 K, the bcc phase persisted up to ∼38 GPa. The hcp phase appeared near 8 GPa in the pre‐melted sample, and near 17 GPa in the powder sample. The appearance of the hcp phase in the pre‐melted sample reconciles the reported changes in electrical resistivity of a similar sample, thus resolving the low‐pressure region of the phase diagram. The resulting high‐temperature Birch‐Murnaghan equation of state (EoS) and thermal EoS based on the Mie‐Gruneisen‐Debye model of the bcc and hcp structures are consistent with, and complement the literature data at higher pressures. The calculated densities based on the thermal EoS of Fe‐9wt.%Si indicate that both bcc and hcp phases agree with the reported core density estimates for the Moon and Mercury.

Berrada, Meryem↗
DOE OSTI2024

Sound Velocities of Stishovite at Simultaneous High Pressure and High Temperature Suggest an Eclogite‐Rich Layer Beneath the Hawaii Hotspot

Compressional and shear wave velocities of polycrystalline stishovite (SiO 2 ) have been measured at simultaneous high pressures and temperatures up to 14.5 GPa and 800°C. By fitting velocities to the finite strain equations, the elastic moduli and density were determined to be K S0 = 306.6(46) GPa, $K$$^{′}_{S}$ = 4.92(10), ∂K S /∂T = −0.024(1) GPa/K, G 0 = 229.0(34) GPa, G′ = 1.07(10), ∂G/∂T = −0.017(1) GPa/K, ρ 0 = 4.287(2) g/cm 3 . Our modeling suggested that, in the eclogite, coesite-stishovite transition can increase P and S wave velocities by 2.4% and 3.5%, respectively. A comparison between geophysical observations and our model shows that the coesite-stishovite phase transition in the eclogite can potentially be responsible for the occurrence of the X discontinuity beneath Hawaii. In addition, our current results suggest an eclogite-rich layer between 340 and 450 km depth beneath Hawaii. The eclogite concentration at the top and bottom of the layer is 41–55 vol% and >77 vol%, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reassessment of Birch's Law on hcp‐Fe From Ultrasonic Sound Velocity Measurement and Implications on the Velocity Profiles of Earth's Inner Core

Here, we performed in situ X-ray diffraction and ultrasonic sound velocity measurements on hcp-Fe up to 15 GPa, 873 K in a multi-anvil apparatus. The elastic moduli and their pressure and temperature derivatives were determined by fitting the velocity and density data to the third-order finite strain equations, yielding K S0 = 169.0(57) GPa, K$^{′}_{S0}$ = 5.4(6), (∂K S /∂T) P = −0.031(3) GPa/K, G 0 = 104.5(27) GPa, G$^{′}_{0}$ = 1.7(2), (∂G/∂T) P = −0.060(2) GPa/K. Within the experimental P-T range, we find significant temperature effect on the density-velocity (ρ − V P or S ) relations and caution the use of the temperature-independent Birch's law for extrapolation to core conditions. Furthermore, temperature-induced velocity decrease is more significant in V S than in V P , offering a possible explanation for the high Poisson's ratio in the core. Extrapolations based on our results together with previous experimental data suggest that V P of hcp-Fe aligns with PREM at Earth's core conditions, while Vs and density are approximately 10% and 2.7% higher than PREM, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Externally Heated Diamond ANvil Cell Experimentation (EH-DANCE) for studying materials and processes under extreme conditions

Externally heated diamond anvil cells provide a stable and uniform thermal environment, making them a versatile device to simultaneously generate high-pressure and high-temperature conditions in various fields of research, such as condensed matter physics, materials science, chemistry, and geosciences. The present study features the Externally Heated Diamond ANvil Cell Experimentation (EH-DANCE) system, a versatile configuration consisting of a diamond anvil cell with a customized microheater for stable resistive heating, bidirectional pressure control facilitated by compression and decompression membranes, and a water-cooled enclosure suitable for vacuum and controlled atmospheres. This integrated system excels with its precise control of both pressure and temperature for mineral and materials science research under extreme conditions. Here, we showcase the capabilities of the system through its successful application in the investigation of the melting temperature and thermal equation of state of high-pressure ice-VII at temperatures up to 1400 K. The system was also used to measure the elastic properties of solid ice-VII and liquid H 2 O using Brillouin scattering and Raman spectra of carbonates using Raman spectroscopy, highlighting the potential of the EH-DANCE system in high-pressure research.

Instruments & Instrumentation↗
DOE OSTI2022

Implications of Sound Velocities of Natural Topaz on the Seismic L–Discontinuity

Compressional and shear wave velocities of topaz have been measured by ultrasonic interferometry in a multi-anvil apparatus up to 13 GPa at room temperature. By fitting the measured velocities under pressure to finite strain equations, the elastic moduli of topaz and their pressure derivatives were obtained, yielding K S0 = 165.5 (25) GPa, K S ' = 2.9 (1), G 0 = 116.5 (17) GPa, and G' = 1.0 (1). Modeling of the velocity profiles of subducted sediments suggests that at 8 GPa (~240 km depth) the P- and S- wave velocities of the subducted sediments exhibit a first order increase of 10% and 11%, respectively. Furthermore, the comparison between seismic observations and velocity contrasts of sediment + MORB model at 240 km shows dehydration of a 1.5–3.9 km thick sediment layer can potentially contribute to the seismically observed Lehmann discontinuity in Tonga, Japan, Philippine Sea, South America, Indonesia, and South Shetland subduction zones.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sound velocities of iron-nickel (Fe90Ni10) alloy up to 8 GPa and 773 K: The effect of nickel on the elastic properties of bcc-iron at high P-T

Sound velocities of iron and iron-based alloys at high pressure and high temperature are crucial for understanding the composition and structure of Earth’s and other telluric planetary cores. In this study, we performed ultrasonic interferometric measurements of both compressional (ν P ) and shear (ν S ) velocities on a polycrystalline body-centered-cubic (bcc)-Fe 90 Ni 10 up to 8 GPa and 773 K. The elastic moduli and their pressure and temperature derivatives are derived from least-square fits to third-order finite strain equations, yielding K S0 = 154.2(8) GPa, G 0 = 73.2(2) GPa, K' S0 = 4.6(2), G' 0 = 1.5(1), ∂K S /∂T = –0.028(1) GPa/K, and ∂G/∂T = –0.023(1) GPa/K. Furthermore, a comparison with literature data on bcc-Fe suggests that nickel not only decreases both P and S wave velocities but also weakens the temperature effects on the elastic moduli of Fe-Ni alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhanced Visibility of Subduction Slabs by the Formation of Dense Hydrous Phase A

Abstract Phase A (Mg 7 Si 2 O 8 (OH) 6 ) is one of the important dense hydrous magnesium silicates in subducting slab, because it forms after the breakdown of antigorite serpentine and could be the dominant hydrous phase in the upper‐mantle deep slab for the water transportation into deep Earth. In this study, the compressional ( P ) and shear ( S ) wave velocities of phase A were measured at simultaneous pressure and temperature conditions up to 11 GPa and 1073 K. Combined with elastic properties of olivine and pyroxenes, we calculate the hydration effect on the velocities of harzburgite lithology in cold subduction zones throughout the depth ranges where phase A is thermodynamically stable. Our calculations suggest that the hydration increases both P ‐ and S ‐wave velocities of harzburgite; at ∼5 wt% hydration, its seismic detectability is enhanced by 1%–1.5% in velocity contrasts relative to its anhydrous counterpart.

Cai, Nao↗
DOE OSTI2021

Anomalous elastic behavior of tantalum at high pressures: Experimental and theoretical studies

Elastic wave velocities of polycrystalline tantalum have been measured up to 13.6 GPa at room temperature using ultrasonic interferometry technique in a multi-anvil apparatus. The bulk and shear moduli, as well as their pressure derivatives are obtained using Eulerian 3rd order finite strain equations, yielding K S0 = 193.9(29) GPa, G 0 = 69.3(10) GPa, K S0' = 3.18(5) and G 0' = 0.88(1). Here the Steinberg-Guinan yield stress model is examined using the current shear modulus and its pressure derivative, where a slightly lower A 0 = 0.0127 GPa –1 compared to previous studies is obtained. First-principles calculations on the elasticity of tantalum have also been performed up to 200 GPa. Anomalous softening of the elastic shear constant C 44 and shear wave velocity V S is observed between 80– 180 GPa, whereas the anisotropy shows a softening-stiffening behavior with increasing pressure and reaches a minimum at around 150 GPa. Such anomalies might commonly originate from the nesting of Fermi surface for Group VB metals.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermoelastic properties of tungsten at simultaneous high pressure and temperature

In this work, the compressional ( P ) and shear wave velocities ( S ) and unit cell volumes (densities) of polycrystalline tungsten (W) have been measured simultaneously up to 10.5 GPa and 1073 K using ultrasonic interferometry in conjunction with x-ray diffraction and x-radiography techniques. Thermoelastic properties of W were derived using different methods. We obtained the isothermal bulk modulus K T 0 = 310.3(1.5) GPa, its pressure derivative K ' T 0 = 4.4(3), its temperature derivative at constant pressure ( ∂ K T / ∂ T ) P = – 0.0138 ( 1 ) GPa K – 1 and at constant volume ( ∂ K T / ∂ T ) V = – 0.0050 GPa K – 1 , the thermal expansion α ( 0, T ) = 1.02(27) × 10 –5 + 7.39(3.2) × 10 –9 T (K –1 ), as well as the pressure derivative of thermal expansion ( ∂ α / ∂ P ) T = – 1.44 ( 1 ) × 10 – 7 K – 1 GP a – 1 based on the high-temperature Birch–Murnaghan equation of state (EOS), the Vinet EOS, and thermal pressure approach. Finite strain analysis allowed us to derive the elastic properties and their pressure/temperature derivatives independent of the choice of pressure scale. A least-squares fitting yielded K S 0 = 314.5(2.5) GPa, K S 0 ' = 4.45(9), (∂ K S /∂ T ) P = – 0.0076(6) GPa K –1 , G 0 = 162.4(9) GPa, G 0 ' = 1.8(1), (∂ G /∂ T ) P = – 0.0175(9) GPa K –1 , and α 298 K = 1.23 × 10 – 5 K – 1 . Fitting current data to the Mie–Grüneisen–Debye EOS with derived θ 0 = 383.4 K yielded γ 0 = 1.81 ( 6 ) and q = 0.3 . The thermoelastic parameters obtained from various approaches are consistent with one another and comparable with previous results within uncertainties. Our current study provides a complete and self-consistent dataset for the thermoelastic properties of tungsten at high P – T conditions, which is important to improve the theoretical modeling of these materials under dynamic conditions.

36 MATERIALS SCIENCE↗