Search NASA⌕ Search

Engineering topics

Wang, Tianyao

Publications and source records attributed to Wang, Tianyao.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Phase patterning of metallic glasses through superfast quenching of ion irradiation-induced thermal spikes

Amorphous metallic glasses (MGs) convert to crystalline solids upon annealing at a high temperature. Such a phase change, however, does not occur with the local melting caused by damage cascades introduced by ion irradiation, although the resulting thermal spikes can reach temperatures > 1000 K. This is because the quenching rate of the local melting zone is several orders of magnitude higher than the critical cooling rate for MG formation. Thus the amorphous structure is sustained. This mechanism increases the highest temperature at which irradiated MG sustains amorphous phase. More interestingly, if an irradiated MG is pre-annealed to form a polycrystalline structure, ion irradiation can locally convert this crystalline phase to an amorphous phase if the grains are nanometers in size and comparable to the damage cascade volume size. Combining pre-annealing and site selective ion irradiation, patterned crystalline-amorphous heterogeneous structures have been fabricated. This finding opens new doors for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A quantitative study of retention and release of deuterium and tritium during irradiation of y-LiAlO2 pellets

This study reports on the quantification of deuterium in ion-irradiated gamma-LiAlO2 pellets as a function of dose and temperature. The gamma-LiAlO2 pellets were sequentially irradiated with He+ and D2+ ions to the same fluences of 5E16, 1E17 and 2E17 He++D+/cm2 at 188 K. Additional irradiation was performed to 1E17, 2E17 and 4E17 He++D+/cm2 at 573 K. A set of the pellets irradiated at 188 K was shipped and stored at low temperatures from 80 to 132 K and characterized using time-of-flight secondary ion mass spectrometry at ~173 K. The deuterium depth profiles show a Gaussian-like distribution in the low-temperature pellets. The total deuterium retention is found to be directly proportional to the ion fluence. About 27 at.% of the implanted deuterium atoms were released from the pellet irradiated to 2E17 He++D+/cm2 at 188 K during storage at room temperature for ~1 month. Retention of the trapped or bound deuterium during ion irradiation at 573 K increases initially with ion fluence and tends to saturate at a high fluence. The amount of the released deuterium is observed to be quantitatively consistent with that of the released tritium from similar standard pellets during neutron irradiation at 573 K.

Deuterium retention and release, ion irradiation, ↗
DOE OSTI2020

Irradiation-induced swelling of pure chromium with 5 MeV Fe ions in the temperature range 450–650 °C

A surface coating using pure chromium has been proposed to increase the accident tolerance of Zircaloy cladding in pressurized water reactors. However, there is not much irradiation experience with Cr alloys and especially pure Cr. In the present study, pure chromium was irradiated with 5 MeV Fe ions to 50 peak dpa (displacements per atom) at temperatures of 450, 500, 550, 600 and 650 °C. Then irradiation at the peak swelling temperature of 550 °C was conducted to 50, 100, 150 peak dpa. Swelling at 50 dpa was observed over the entire temperature range studied, 450–650 °C, but appeared to be decreasing strongly at the temperature boundaries of the experiment. After an initial transient of rapid swelling, chromium was observed to swell at a rate of ~0.03–0.04%/dpa (up to 120 local dpa), which is much lower than pure Fe at 0.2%/dpa. This low swelling rate was found to be relatively insensitive to dpa rate, which varied by a factor of ~2 over the depth of data collection. Here, swelling was observed to begin quickly with an incubation period less than 10 dpa. Self-organization in the form of void ordering was observed to be developing at 50 dpa, becoming better defined with increasing dose. The void alignment direction is determined to be the $\langle$111$\rangle$ axial direction.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain modulation using defects in two-dimensional MoS 2

We investigate the nature of strain in MoS 2 and correlate it to defect types and densities, while systematically assessing the tolerance of this low dimensional material to He and Au ion irradiations. Through a series of theoretical predictions and experimental observations, we establish the onset of the crystalline-to-amorphous transition in MoS 2 and identify sulfur vacancies as the most favorable defects introduced during irradiation. We note the presence of both tensile and compressive strains, which depend on the types of defects introduced into the lattice and vary with increasing fluence. In conclusion, the results show that defects can be used to tune strain in two-dimensional materials and provide an exciting pathway for using external stimuli to control properties of low dimensional materials.

2-dimensional systems↗
DOE OSTI2020

Radiation response of FeCrAl-coated Zircaloy-4

Coating the surface of Zircaloy-4 light water reactor fuel cladding tube is of considerable interest for enhancing its accident tolerance. In this study, thermal annealing of FeCrAl-coated Zircaloy-4 at 725 °C for 500 h, was used to induce interfacial reactions between Zircaloy-4 and FeCrAl. The interface zones were then irradiated by 3.5 MeV Zr ions at 400 °C, up to 50, 100, 150 peak dpa values. Transmission electron microscopy (TEM) and scanning TEM were used to characterize microstructural and composition changes before and after ion irradiation. Three interfacial phases were identified: FeZr 3 , (Fe,Cr) 2 Zr, and ZrC. The widest intermetallic layer, FeZr3, had large grains. The narrower phases, (Fe,Cr)2Zr and ZrC, contained small grains and were often mixed. The unexpected observation of the ZrC phase was attributed to the presence of very small impurity level concentrations of carbon in the powder material. No void swelling was observed in any of the phases, including the FeCrAl coating and Zircaloy-4 substrate. (Fe,Cr) 2 Zr, however, fully amorphized after irradiation, even at the lowest dpa.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ni coating on 316L stainless steel using cage plasma treatment: Feasibility and swelling studies

A modified cage plasma nitriding technique is used to coat a Ni film onto a 316L substrate as a protective layer for austenitic steels in molten fluoride salts. The coating is achieved by deposition of Ni atoms sputtered from a Ni cage with a 316L substrate floated at the same potential as the cage to reduce plasma sputtering on the substrate. The Ni coating is porosity-free and precipitation-free and forms a γ-(Fe, Ni) phase due to interdiffusion from the substrate. Beneath the interdiffusion layer exists a thick γ-phase layer mainly affected by long-range nitrogen diffusion along the grain boundary. This layer develops grain boundary Cr nitride precipitates. Ion irradiation on the polished cross-section of the plasma-treated sample shows no void swelling in the surface-deposited Ni layer, very limited void formation in N diffusion layer, and significant void swelling in bulk unaffected by nitrogen. The studies demonstrate the feasibility of the technique for Ni coating and show good swelling resistance of the coating layer and N diffusion-affected layer. Mechanisms are discussed in this paper.

36 MATERIALS SCIENCE↗