Search NASA⌕ Search

Engineering topics

Wang, Xuming

Publications and source records attributed to Wang, Xuming.

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of CO 2 on the water slip flow at silica surfaces for nanometer slit pores of talc

In our previous study, Molecular Dynamics (MD) simulated water flow with no dissolved gas in nanometer slit pores of the hydrophobic talc surfaces revealed a slip length of about 0.5 nm, which is close to the size of “water exclusion zone” but much less than experimental slip length. Atomic Force Microscopy (AFM) imaging confirmed the presence of pancake shape nanobubbles at the hydrophobic talc (001) surface (size from tens to hundreds of nanometers). The effect of CO 2 on water slip flow in talc nanopores is reported to reveal the importance of dissolved gas for confined fluid flow. MD simulated 7 nm CO 2 nanobubbles were found to attach and spread at the talc (001) surface, consistent with the AFM observation. Simulated CO 2 saturated water flow in the slit pores of talc (001) surfaces predicted the generation of CO 2 nanobubbles at the end of the slit pore, due to the stabilization of a CO 2 film at the talc (001) surfaces and a water barrier at the edge surfaces of talc. A “critical thickness” of about 1.5 nm was found for CO 2 nanobubbles to be stabilized at the end of the talc (001) surface. With 1.5 nm CO 2 nanobubbles at the talc (001) surface of a 6 nm slit pore, a water slip length of 1.8 nm was determined. Furthermore, the nanometer slit pore simulations with dissolved CO 2 in water revealed an increased slip length. It is expected that an increased slip length value would be found with an increased CO 2 film thickness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multiscale water drop contact angles at selected silica surfaces

In this paper, multiscale advancing contact angles for glycerol/water drops at silica surfaces are reported for millidrops, submicron-drops, and nanodrops. Selected silica surfaces were muscovite, silicon, and talc. The contact angles for millidrops (1–2 mm) were determined by the traditional sessile drop technique. For submicron-drops (0.1–1.0 μm), a hollow tip Atomic Force Microscope (AFM) procedure was used. The contact angles for nanodrops (~7 nm) were examined from Molecular Dynamics (MD) simulation. The results were compared to evaluate the effect of drop size on the contact angle. In the case of the hydrophobic talc surface, the 75° advancing contact angle did not vary significantly with drop size. For the hydrophilic muscovite surface, the water drop wet the surface and an advancing contact angle of about 10° was found for the millidrops and submicron-drops. However, for the MD simulated nanodrops, attachment and spreading of the ~7 nm drop created a 2D film of molecular dimensions, the contact angle of which was difficult to define and varied from 0° to 17°. Perhaps of equal interest from the MD simulation results was that the spreading of the glycerol/water nanodrop at the muscovite surface resulted in crystallographic directional transport of water molecules to the extremities of the 2D film. Such separation and segregation left the center of the film with an increased concentration of glycerol. Based on these results, the line tension, which has been found in other investigations to account for contact angle decrease with a decrease in drop size, does not seem to be a significant factor in this study.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Simulation and analysis of slip flow of water at hydrophobic silica surfaces of nanometer slit pores

Water flow in nanopores is controlled fundamentally by pore wettability and interfacial water features. In the research herein reported, Molecular dynamics (MD) was used to simulate water flow in nanometer slit pores of silica surfaces with variable wetting characteristics. Compared to Couette flow, the simulated slit-pores of the talc (001) and octadecyltrichlorosilane (OTS) monolayer surfaces exhibited water flow enhancement and a positive slip length at the interface, whereas water flow velocity at the quartz (001) and amorphous silica surfaces was zero, adhering to the no slip condition. More intensive interactions between the interfacial water and hydrophilic silica surfaces were confirmed by MD simulation and sum-frequency vibrational spectroscopy (SFVS) results. A water exclusion zone of approximately 3 Å was found at the hydrophobic silica surfaces by quantitative MD interfacial water analysis and validated by SFVS. This exclusion zone dimension was similar in magnitude to the slip length (4–5 Å) as determined from simulated water flow in hydrophobic silica slit pores. The simulated slip lengths at the hydrophobic surfaces (0.2–1 nm) were significantly less than the experimental slip lengths (>40 nm) reported in the literature. In the case of the experimental results, this difference appears to be due to nanobubbles expected to be present at hydrophobic surfaces.

42 ENGINEERING↗