Engineering topics
Publications and source records attributed to Wang, Yilin.
Stimuli-responsive RAPs with disulfide bonds enable in-situ electrode cleaning via UV or electrochemical stimuli, effectively removing fouling and restoring electrode performance in electrochemical flow cells.
Yttrium-modified dealuminated Betazeolite (Y-BEA) represents a type of Lewis acid zeolite that has gained attention for its potential to efficiently catalyze the conversion of biomass-derived oxygenates. The structure of the Y active sites and their dynamics during biomass conversion reactions, which normally involve substantial amounts of water, necessitate thorough investigation for the rational design of more active and stable catalysts. Here, we conducted a study where a series of Y-BEA catalysts with different yttrium loadings (1–7 wt.%) were subjected to hydrothermal treatment (450 °C, 20% water) and investigated for their structural and catalytic activity changes through a combination of multiple characterizations and kinetic measurements. The number of acid sites of Y-BEA decreased without a change in acid strength following the hydrothermal treatment, which was confirmed by the results of acid site titration, infrared spectroscopy of probe molecules, and kinetic measurements for probe reactions (acetone aldol condensation). Structural analysis using X-ray diffraction (XRD), specific surface area measurement, X-ray absorption spectroscopy (XAS), and X-ray photoelectron spectroscopy (XPS) demonstrated that both the zeolite structure and the isolation status of the Y site remain intact after hydrothermal treatment. Further, the Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) spectra, thermogravimetric analysis (TGA), and operando 1 H and 29 Si magic-angle spinning (MAS) nuclear magnetic resonance (NMR) revealed the dehydroxylation of Y-BEA induced by hydration-rearrangement-condensation restructuring during the high-temperature steam treatment. Dehydroxylation affects the structure of Y sites by reducing their vicinal silanol sites. In conclusion, this conversion of Lewis acidic Y sites into nonacidic sites is the primary factor behind the change in acid site quantity and catalytic activity on Y-BEA.
In this article, elevated temperature molten Na batteries are seeing a resurgence of interest for low-cost electrochemical energy storage for the grid. Of the many recent innovations in this battery concept, new methods focused on intermediate temperature operation (e.g. 110–190 °C) have gained prominence as a way to enable comparable performance with less thermal energy loss and lower-cost materials of construction. However, the poor wettability of molten Na on suitable solid-electrolyte separators such as sodium Beta Alumina Solid-Electrolyte (Na-β”-Al 2 O 3 , ‘BASE’) requires continued innovation in interface engineering to promote full utilization of the solid-electrolyte surface area and minimize cell resistance. There have been many successful approaches to improve Na-wettability to-date including heat treatment in an inert atmosphere to remove adsorbed surface species, deposition of alloying metals such as Pb, Sn, or Bi, and use of carbon-based interfacial layers. However, these approaches either lack the ability to provide good wetting at very low temperatures (near the melting point of Na) or rely on non-scalable processes and/or toxic/expensive metals. To solve these issues, a new carbon-based sodiophilic treatment is demonstrated, which utilizes inexpensive components to form a meso/macroporous sodiophilic layer, is easily applied via drop-casting or spray-coating, provides excellent wetting as low as 110 °C, and is completely metal-free. It is found that the good sodium wetting can be attributed to the wider range of pore sizes in the carbon layers demonstrated in this study. Na wetting may occur as surface tension is initially broken by larger pores, followed by the intrusion of molten Na into smaller pores due to the apparent intrinsic affinity of Na-metal for carbon surfaces, in conjunction with the capillarity effect. Low cell-level area specific resistances of 20–30 and 13–15 Ω·cm 2 are demonstrated at 110 and 140 °C respectively. Finally, the utility of this metal-free wetting layer for solid-Na anodes is explored, showing that the metal-free wetting layer can reach a critical current density of 1.88 mA·cm -2 at 30 °C.
Abstract Obtaining a well‐accurate vertical distribution active layer morphology through the air‐printing process is an essential task for achieving efficient scalable large‐area organic solar cells (OSCs). In this target, the desired and controllable pseudo planar heterojunction (PPHJ) active layer structure with suitable phase separation is developed by pre‐deposited D18‐Cl layer under the PM6:BTP‐eC9 film via an eco‐friendly manufacturing method. The addition of the D18‐Cl regulates molecular crystallization and leads to an ideal vertical stratification while simultaneously suppressing voltage loss, optimizing energetic disorder, and carrier management. Impressively, the optimal PPHJ devices perform superior power conversion efficiencies (PCEs) of 19.05% (100 nm), 17.33% (300 nm), and 14.14% (4 cm 2 ) compared to the BHJ devices. Importantly, the PPHJ OSCs also exhibit an impressive extrapolated T 80 (the time required to reach 80% of initial PCE) of long‐time storage and operational stability, as well as thermal stability.
Two series of Cu/SSZ-13 catalysts were synthesized via aqueous solution and solid-state ion exchange using SSZ-13 supports of varying Si/Al ratios. The isolated and multinuclear Cu content of these catalysts were determined by H 2 temperature programmed reduction (H 2 -TPR). Multinuclear Cu in these catalysts, including in situ Cu- dimers formed from ZCu II OH coupling and permanent CuO clusters, are active species for dry NO oxidation. NH 3 oxidation on these catalysts follows an internal SCR (i-SCR) mechanism, i.e., a portion of NH 3 is first oxidized to NO, then NO is selectively reduced by the remaining NH 3 to N 2 . NH 3 oxidation displays distinct kinetic behavior below ~300 °C and above ~400 °C. At low temperature the results indicate that NH 3 -solvated mobile Cu-ions are the active centers. CuO clusters, when present, also contribute to the low temperature activity by catalyzing NH 3 oxidation to NO. At high temperature, in situ Cu-dimers and CuO clusters catalyze NH 3 oxidation to NO, and isolated Cu-ions catalyze SCR to realize the cascade turnovers. For both NO and NH 3 oxidation, Cu-dimers balanced by framework charges of close proximity appear to be more active than Cu-dimers balanced by distant framework charges. However, the former Cu-dimers are less stable than the latter and tend to split into monomers in the presence of vicinal Brønsted acid sites. Via density functional theory (DFT) calculations, the i-SCR mechanism for low temperature NH 3 oxidation, i.e., the energetic favorability for the involvement of the NO intermediate, is justified. Furthermore, the DFT results also agree with experimental data that the formation of Cu-dimers from ZCu II OH dimerization is essential for NH 3 oxidation at high temperature.
Power-conversion-efficiencies (PCEs) of organic solar cells (OSCs) in laboratory, normally processed by spin-coating technology with toxic halogenated solvents, have reached over 19%. However, there is usually a marked PCE drop when the blade-coating and/or green-solvents toward large-scale printing are used instead, which hampers the practical development of OSCs. Here, a new series of N-alkyl-tailored small molecule acceptors named YR-SeNF with a same molecular main backbone are developed by combining selenium-fused central-core and naphthalene-fused end-group. Thanks to the N-alkyl engineering, NIR-absorbing YR-SeNF series show different crystallinity, packing patterns, and miscibility with polymeric donor. The studies exhibit that the molecular packing, crystallinity, and vertical distribution of active layer morphologies are well optimized by introducing newly designed guest acceptor associated with tailored N-alkyl chains, providing the improved charge transfer dynamics and stability for the PM6:L8-BO:YR-SeNF-based OSCs. As a result, a record-high PCE approaching 19% is achieved in the blade-coating OSCs fabricated from a green-solvent o-xylene with high-boiling point. Notably, ternary OSCs offer robust operating stability under maximum-power-point tracking and well-keep > 80% of the initial PCEs for even over 400 h. Our alkyl-tailored guest acceptor strategy provides a unique approach to develop green-solvent and blade-coating processed high-efficiency and operating stable OSCs, which paves a way for industrial development.
Coexistence of localized and extended excitations is central to the macroscopic properties of correlated materials. For 5d transition-metal compounds, electron correlations alone generally do not lead to a metal-insulator (Mott) transition, with insulating behavior usually resulting from their coupling with magnetic ordering and/or structural distortions. 1T–TaS 2 is a prototypical example of such correlated insulating behavior, with a high-symmetry metallic phase transforming into a distorted, charge-density wave (CDW) insulating state at low temperatures. The nature of the insulating phase as well as the existence and relevance of the localized electron physics remains debated. We resolve this standing controversy in 1T–TaS 2 combining resonant inelastic x-ray spectroscopy and first-principles calculations. We observe five electronic excitations arising from the interband transitions of the Ta 5d orbitals and the S 3p ligand state, with none of the excitations on the order of the Mott gap. These excitations cannot be explained within the framework of standard multiplet calculations that assume a localized wave function, but instead, are captured by a band-theory framework accounting for the low symmetry of the crystal field in the CDW state. Our findings suggest that the electronic properties of 1T–TaS 2 are dominated in the visible by both plasmonic quasiparticles and interband transitions, with no resonance associated with a putative Mott transition observed in the 0–3 eV energy range. Finally, our discovery provides insights into the electron localization and the Mott vs band-insulator debate in 1T–TaS 2 and other transition-metal materials.
We reveal in this study the fundamental low-energy landscape in the ferrimagnetic Sr 2 CrReO 6 double perovskite and describe the underlying mechanisms responsible for the three low-energy excitations below 1.4 eV. Here, based on resonant inelastic x-ray scattering and magnetic dynamics calculations, and experiments collected from both Sr 2 CrReO 6 powders and epitaxially strained thin films, we reveal a strong competition between spin-orbit coupling, Hund’s coupling, and the strain-induced tetragonal crystal field. Here, we also demonstrate that a spin-flip process is at the origin of the lowest excitation at 200 meV, and we bring insights into the predicted presence of orbital ordering in this material. We study the nature of the magnons through a combination of ab initio and spin-wave theory calculations, and show that two nondegenerate magnon bands exist and are dominated either by rhenium or chromium spins. The rhenium band is found to be flat at about 200 meV (±25 meV) through X-L-W-U high-symmetry points and is dispersive toward Γ.
Low-temperature standard NH 3 -SCR over copper-exchanged zeolite catalysts occurs on NH 3 -solvated Cu-ion active sites in a quasi-homogeneous manner. As key kinetically relevant reaction steps, the reaction intermediate Cu II (NH 3 ) 4 ion hydrolyzes to Cu II (OH)(NH 3 ) 3 ion to gain redox activity. The Cu II (OH)(NH 3 ) 3 ion also transfers between neighboring zeolite cages to form highly reactive reaction intermediates. Via operando electron paramagnetic resonance spectroscopy and SCR kinetic measurements and density functional theory calculations, we demonstrate here that such kinetically relevant steps become energetically more difficult with lower support Brønsted acid strength and density. Consequently, Cu/LTA displays lower Cu atomic efficiency than Cu/CHA and Cu/AEI, which can also be rationalized by considering differences in their support topology. By carrying out hydrothermal aging to eliminate support Brønsted acid sites, both Cu II (NH 3 ) 4 ion hydrolysis and Cu II (OH)(NH 3 ) 3 ion migration are hindered, leading to a marked decrease in Cu atomic efficiency for all catalysts.
Here, the impacts of Pd poisoning to the activity, selectivity, and hydrothermal stability of Cu/SSZ-13 selective catalytic reduction (SCR) catalysts are reported. Pd lowers DeNOx efficiency of Cu/SSZ-13 via two mechanisms: (1) displacing SCR active sites in the form of isolated Pd-ions, and (2) catalyzing non-selective NH 3 oxidation in the form of PdO. The first mechanism works by the diffusion of isolated Pd-ions into chabazite cages to displace ZCu II OH SCR active species, and it occurs on Cu/SSZ-13 catalysts with and without external surface CuO clusters in similar fashion. In contrast, the second mechanism works differently with and without external surface CuO clusters. For Cu/SSZ-13 catalyst without external CuO clusters (i.e., primarily isolated Cu-ions), PdO leads to significant decrease of DeNOx efficiency at reaction temperatures above ~400°C due to its non-selective NH 3 oxidation activity at high temperatures. However, this poisoning effect becomes much less impactful on Cu/SSZ-13 catalyst containing CuO clusters. This is due to the formation of CuO-PdO solid solution via interactions between CuO and PdO, which reduces non-selective NH 3 oxidation potential. Furthermore, this solid solution formation even mitigates adverse effects caused by hydrothermal aging. Hence, the poisoning effects of Pd are closely related to Cu speciation and spatial distribution of a Cu/SSZ-13 catalyst. Finally, this study suggests a strategy in eliminating Pd poisoning, that is, the introduction of an oxide phase that effectively traps PdO but does not adversely influence SCR.
Increasing redox-active species concentrations can improve viability for organic redox flow batteries by enabling higher energy densities, but the required concentrated solutions can become viscous and less conductive, leading to inefficient electrochemical cycling and low material utilization at higher current densities. To better understand these tradeoffs in a model system, we study a highly soluble and stable redox-active couple, N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT), and its bis(trifluoromethanesulfonyl)imide radical cation salt (MEEPT-TFSI). We measure the physicochemical properties of electrolytes containing 0.2–1 M active species and connect these to symmetric cell cycling behavior, achieving robust cycling performance. Specifically, for a 1 M electrolyte concentration, we demonstrate 94% materials utilization, 89% capacity retention, and 99.8% average coulombic efficiency over 435 h (100 full cycles). This demonstration helps to establish potential for high-performing, concentrated nonaqueous electrolytes and highlights possible failure modes in such systems.
Understanding the physical and chemical processes occurring in concentrated electrolyte solutions is required to achieve redox flow batteries with high energy density. Highly concentrated electrolyte solutions are often studied in which collective crowded interactions between molecules and ions become predominant. In this work, experimental and computational methods were used to examine non-aqueous electrolyte solutions in two different states of charge as a function of redoxmer concentration. As the latter increases and the ionic association strengthens, the electric conductivity passes through a maximum and the solution increasingly gels, which is seen through a rapid non-linear increase in viscosity. We establish that the structural rigidity of ionic networks is closely connected with this loss of fluidity and show that charging generally yields softer ionic assemblies with weaker attractive forces and improved dynamical properties.
Abstract In contrast to classical bulk heterojunction (BHJ) in organic solar cells (OSCs), the quasi‐homojunction (QHJ) with extremely low donor content (≤10 wt.%) is unusual and generally yields much lower device efficiency. Here, representative polymer donors and nonfullerene acceptors are selected to fabricate QHJ OSCs, and a complete picture for the operation mechanisms of high‐efficiency QHJ devices is illustrated. PTB7‐Th:Y6 QHJ devices at donor:acceptor (D:A) ratios of 1:8 or 1:20 can achieve 95% or 64% of the efficiency obtained from its BHJ counterpart at the optimal D:A ratio of 1:1.2, respectively, whereas QHJ devices with other donors or acceptors suffer from rapid roll‐off of efficiency when the donors are diluted. Through device physics and photophysics analyses, it is observed that a large portion of free charges can be intrinsically generated in the neat Y6 domains rather than at the D/A interface. Y6 also serves as an ambipolar transport channel, so that hole transport as also mainly through Y6 phase. The key role of PTB7‐Th is primarily to reduce charge recombination, likely assisted by enhancing quadrupolar fields within Y6 itself, rather than the previously thought principal roles of light absorption, exciton splitting, and hole transport.
Hund metals are multiorbital systems with 3d or 4d electrons exhibiting both an itinerant character and local moments, and they feature Kondo-like screenings of local orbital and spin moments, with suppressed coherence temperatures driven by Hund's coupling J H . They often exhibit magnetic order at low temperature, but how the interaction between the Kondo-like screening and long-range magnetic order is manifested in the quasiparticle spectrum remains an open question. Here, we present the spectroscopic signature of such an interaction in a Hund metal candidate MnSi exhibiting weak ferromagnetism. Our photoemission measurements reveal renormalized quasiparticle bands near the Fermi level with strong momentum dependence: The ferromagnetism manifests through possibly exchange-split bands (Q1) below T C , while the spin/orbital screenings lead to the gradual development of quasiparticles (Q2) upon cooling. Our results demonstrate how the characteristic spin/orbital coherence in a Hund metal could coexist and compete with the magnetic order to form a weak itinerant ferromagnet, via quasiparticle bands that are well separated in momentum space and exhibit distinct temperature dependence. Here, our results imply that the competition between the spin/orbital screening and the magnetic order in a Hund metal bears interesting similarities to the Kondo lattice systems
We report a detailed experimental study of peculiar thixotropic dynamics of carbon black (CB, Vulcan XC-72) suspensions in mineral oil, specifically the observation of sequential stress increase then decrease at a fixed shear rate in a step-down test. We verify that such dynamics, though peculiar, come from a true material response rather than experimental artifacts. We also reveal how this long-time stress decay is associated with antithixotropic structural change rather than viscoelastic stress relaxation by using orthogonal superposition (OSP) rheometry to probe viscoelastic moduli during the step-down tests. The orthogonal storage and loss moduli are present, showing this two-timescale recovery then decay response, which demonstrates that this response is antithixotropic, and it involves shear-induced structuring. We further show a mechanical anisotropy in the CB suspension under shear using OSP. Based on the rheological results, a microstructural schematic is proposed, considering qualitatively thixotropic structure build-up, antithixotropic densification, and anisotropic structure evolution. Our observation for these CB suspensions is outside the standard paradigm of thixotropic structure-parameter models, and the elastic response provides us with new insight into the transient dynamics of CB suspensions.
Efficient exciton diffusion and charge transport play a vital role in advancing the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, a facile strategy is presented to simultaneously enhance exciton/charge transport of the widely studied PM6:Y6-based OSCs by employing highly emissive trans-bis(dimesitylboron)stilbene (BBS) as a solid additive. BBS transforms the emissive sites from a more H-type aggregate into a more J-type aggregate, which benefits the resonance energy transfer for PM6 exciton diffusion and energy transfer from PM6 to Y6. Transient gated photoluminescence spectroscopy measurements indicate that addition of BBS improves the exciton diffusion coefficient of PM6 and the dissociation of PM6 excitons in the PM6:Y6:BBS film. Transient absorption spectroscopy measurements confirm faster charge generation in PM6:Y6:BBS. Moreover, BBS helps improve Y6 crystallization, and current-sensing atomic force microscopy characterization reveals an improved charge-carrier diffusion length in PM6:Y6:BBS. Finally, owing to the enhanced exciton diffusion, exciton dissociation, charge generation, and charge transport, as well as reduced charge recombination and energy loss, a higher PCE of 17.6% with simultaneously improved open-circuit voltage, short-circuit current density, and fill factor is achieved for the PM6:Y6:BBS devices compared to the devices without BBS (16.2%).
Elucidating aging mechanisms in real-world applications is a critical component for developing and maintaining Cu/SSZ-13 SCR catalysts. To reveal gaps between laboratory accelerated aging and real-world aging, herein we report thorough comparative studies between 6 representative catalysts. Here, we apply a wide range of catalyst characterization methods, including surface area/porosity analysis, X-ray diffraction (XRD), H 2 -temperature programmed reduction, NH3-temperaure programmed desorption, solid-state nuclear magnetic resonance (NMR), in situ X-ray photoelectron (XPS) and electron paramagnetic resonance (EPR) spectroscopies, to gain atomic-level knowledge on Cu transformation under different aging protocols. We then correlate such knowledge to SCR, NH 3 /NO oxidation kinetic behavior of the catalysts. We found that sulfur aging plays the most important role in interpreting catalyst degradation during real-world application, including direct sulfur poisoning of isolated Cu II SCR active species to CuSO 4 -like species, the agglomeration of such species to multinuclear CuSO 4 clusters, and eventually, CuO formation during desulfation treatments. Such chemistries convert SCR active Cu to SCR inert Cu moieties without severely deteriorating catalyst support integrity. These characteristics are partially replicated by hydrothermal aging in the presence of SOx but are poorly mimicked by hydrothermal aging alone.