Engineering topics

Wang, Yuzhou

Publications and source records attributed to Wang, Yuzhou.

5 records

DOE OSTI2023

Microstructure characterization of electric field assisted sintering (EFAS) sintered metallic and ceramic materials using local thermal diffusivity measurement

Electric Field Assisted Sintering (EFAS, also referred to as spark plasma sintering) is a powerful technology for the consolidation of powder materials. The high heating rate during the sintering process is critical for minimizing energy consumption, but it can also cause microstructure heterogeneities in sintered parts, such as spatially varied porosity. The examination of localized porosity usually requires the use of a scanning electron microscope with a carefully prepared surface. In this paper, photothermal radiometry is used to measure local thermal diffusivity and extract localized porosity of EFAS-sintered parts by using a percolation-threshold model. Applying this approach, we identified the radial position-dependent porosity variation in EFAS parts, which is likely formed due to the large temperature gradient during the sintering process. This approach has a unique advantage because it can measure samples with minimal or no surface preparation, enabling the possibility of in situ characterization in EFAS with proper system modification. Necessary modifications on the measurement approach for EFAS deployment and in situ characterization are also discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Temperature-dependent elastic constants of thorium dioxide probed using time-domain Brillouin scattering

Herein we report the adiabatic elastic constants of single-crystal thorium dioxide over a temperature range of 77–350 K. Time-domain Brillouin scattering, an all-optical, non-contact picosecond ultrasonic technique, is used to generate and detect coherent acoustic phonons that propagate in the bulk perpendicular to the surface of the crystal. These coherent acoustic lattice vibrations have been monitored in two hydrothermally grown single-crystal thorium dioxide samples along the (100) and (311) crystallographic directions. The three independent elastic constants of the cubic crystal (C 11 , C 12 , and C 44 ) are determined from the measured bulk acoustic velocities. The longitudinal wave along the (100) orientation provided a direct measurement of C 11 . Measurement of C 44 and C 12 was achieved by enhancing the intensity of quasi-shear mode in a (311) oriented crystal by adjusting the polarization angle relative to the crystal axes. We find the magnitude of softening of the three elastic constants to be ~2.5% over the measured temperature range. Good agreement is found between the measured elastic constants with previously reported values at room temperature, and between the measured temperature-dependent bulk modulus with calculated values. We find that semi-empirical models capturing lattice anharmonicity adequately reproduce the observed trend. We also determine the acoustic Grüneisen anharmonicity parameter from the experimentally derived temperature-dependent bulk modulus and previously reported temperature-dependent values of volumetric thermal expansion coefficient and heat capacity. This work presents measurements of the temperature-dependent elasticity in single-crystal thorium dioxide at cryogenic temperature and provides a basis for testing ab initio theoretical models and evaluating the impact of anharmonicity on thermophysical properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Irradiation Behavior of Piezoelectric Materials for Nuclear Reactor Sensors

In-situ measurement of surface acoustic wave (SAW) resonators were used to characterize piezoelectric materials behavior in a nuclear reactor environment. Lithium niobate and aluminum nitride devices were tested up to 500°C temperature and 450 kW reactor power (1.9x10 12 n/cm 2 s). The resonant frequency responds to step changes in temperature and power. Materials’ response are inferred from the observed resonant frequency changes, in particular the kinetic behavior is used to determine mechanisms responsible for observed changes. The observed response is attributed to two mechanisms: temperature increase from gamma heating and accumulation of radiation-induced defects. Both of these mechanisms alter the physical properties of the piezoelectric materials, particularly the elastic constants. The demonstrated repeatability and reliability of SAW devices are attractive for sensor applications in extreme environments.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Nir/ai Identification Of Waste Plastics

The program reads a near infrared reflectance (NIR) spectrum from an item of plastic waste, and identifies the type of plastic using an AI model. The spectra and results are displayed to the operator, and recorded in a database.

Bonebright, PatrickN [Idaho National Laboratory (I↗

DOE OSTI2023

An investigation of fracture behaviors of NBG-18 nuclear graphite using in situ mechanical testing coupled with micro-CT

Nuclear graphite contains defects spanning from nanoscale basal cracks to sub-mm scale voids. This study aims to establish an experimental method to investigate pre-existing defects and 3-D crack growth inside nuclear graphite, NBG-18. Three-point bending tests were performed on single-edge notched beam specimens with and without coupling with micro-CT. The fracture toughness was measured to be 1.17 ± 0.06 MPa $\sqrt{{m}}$. Cracks were observed to initiate from the pores and thermal cracks on the edge of the notch and then defect or twist to grow along the pre-existing defects. Crack bridging, defection, and twisting were the primary toughening mechanisms. The crack resistance curve exhibited a trend of rising-plateau-rising that can be related to the interaction of crack front and the pre-existing defects. In conclusion, the results highlight the capability of laboratory micro-CT-based experimental method for the visualization of multi-scale defect interactions, which remains to be a challenge in the characterization of nuclear graphite.

36 MATERIALS SCIENCE↗