Search NASA⌕ Search

Engineering topics

Wang, Zhanhui

Publications and source records attributed to Wang, Zhanhui.

HL-2A's ELM cycle simulations by integrating BOUT++'s drift MHD and transport code

A new integrating model has been developed to couple tokamak edge multiscale magnetohydrodynamic (MHD) events and transport simulations, such as edge-localized mode (ELM) cycles. As a proof of principle, we first start from a set of three-field two-fluid model equations, which includes the pressure, current, and vorticity. Here, the equations are separated into the slowly evolving part of the axisymmetric component by taking a time average of the axisymmetric component. The time-averaged fluxes, which are quadratic in fluctuating quantities, act as driven terms for the time-averaged axisymmetric quantities that determine the plasma transport, and therefore the large-scale evolution of the plasma profiles. Then the HL-2A's ELM cycles are simulated using the model. Good agreements of ELM size and pedestal recovery time have been achieved for the solutions obtained from the coupled simulation compared with experiment. For one ELM cycle simulation, the coupled code can achieve a speedup of a factor of up to 30 over standalone code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On how structures convey non-diffusive turbulence spreading

Abstract We report on comprehensive experimental studies of turbulence spreading in edge plasmas. These studies demonstrate the relation of turbulence spreading and entrainment to intermittent convective density fluctuation events or bursts (i.e. blobs and holes). The non-diffusive character of turbulence spreading is thus elucidated. The turbulence spreading velocity (or mean jet velocity) manifests a linear correlation with the skewness of density fluctuations, and increases with the auto-correlation time of density fluctuations. Turbulence spreading by positive density fluctuations is outward, while spreading by negative density fluctuations is inward. The degree of symmetry breaking between outward propagating blobs and inward propagating holes increases with the amplitude of density fluctuations. Thus, blob-hole asymmetry emerges as crucial to turbulence spreading. These results highlight the important role of intermittent convective events in conveying the spreading of turbulence, and constitute a fundamental challenge to existing diffusive models of spreading.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The role of shear flow collapse and enhanced turbulence spreading in edge cooling approaching the density limit

Abstract Experimental studies of the dynamics of shear flow and turbulence spreading at the edge of tokamak plasmas are reported. Scans of line-averaged density and plasma current are carried out while approaching the Greenwald density limit on the J-TEXT tokamak. In all scans, when the Greenwald fraction f G = n ¯ / n G = n ¯ / ( I p / π a 2 ) increases, a common feature of enhanced turbulence spreading and edge cooling is found. The result suggests that turbulence spreading is a good indicator of edge cooling, indeed better than turbulent particle transport is. The normalized turbulence spreading power increases significantly when the normalized E × B shearing rate decreases. This indicates that turbulence spreading becomes prominent when the shearing rate is weaker than the turbulence scattering rate. The asymmetry between positive/negative (blobs/holes) spreading events, turbulence spreading power and shear flow are discussed. These results elucidate the important effects of interaction between shear flow and turbulence spreading on plasma edge cooling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

One-dimensional simulation and validation of divertor detachment induced through nitrogen seeding on HL-2A

Divertor detachment is a promising method to solve the power exhaust problem in tokamak devices or even in future magnetic fusion reactors. In this work, a detachment experiment (HL-2A shot #38008) with mixed gas seeding (60% nitrogen and 40% deuterium) is simulated using the SD1D module in BOUT++. In the process from attachment to detachment, the target electron temperature and the target ion saturation current in simulations are found to be consistent with the experimental results measured by Langmuir probes on the target plate. In order to understand the underlying detachment mechanism on HL-2A, this work analyses the role of different particle species in the cases with different seeding rates. It shows that the plasma density varies little and the density of neutrals (D and D 2 ) slightly decreases with the increase of nitrogen seeding rate, such that plasma–neutral interactions cannot effectively reduce plasma energy and plasma momentum in the divertor. The case with a high seeding rate predicts that increasing seeding rate cannot reach a target temperature lower than 2.5 eV, which is the required temperature for strong plasma–molecule interactions. Thus, the plasma–molecule interactions may not be important in the divertor during nitrogen seeding. Here this work also studies the parallel forces including (1) force due to the parallel electric field, (2) friction forces, (3) ion- and electron-thermal forces, and (4) collisional reactions (e.g. charge exchange recombination and ionisation). It is found that the friction force between nitrogen ions and other particle species (primarily D + ) is the dominant force towards the target, while ion- and electron-thermal forces are the dominant force pushing nitrogen ions back to upstream. Parallel forces determine the parallel distribution of nitrogen impurities, and therefore decide the region of nitrogen radiation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Estimation of China Fusion Engineering Test Reactor performance and burning fraction in different pellet fueling scenarios by a multi-species radial transport model

Tritium self-sufficiency in future deuterium–tritium fusion reactors is a crucial challenge. As an engineering test reactor, the China Fusion Engineering Test Reactor requires a burning fraction of 3% for the goal to test the accessibility to the future fusion plant. To self-consistently simulate burning plasmas with profile changes in pellet injection scenarios and to estimate the corresponding burning fraction, a one-dimensional multi-species radial transport model is developed in the BOUT++ framework. Here several pellet-fueling scenarios are then tested in the model. The results show that the increased fueling depth improves the burning fraction by particle confinement improvement and fusion power increase. Nevertheless, by increasing the depth, the pellet cooling-down may significantly lower the temperature in the core region. Taking the density perturbation into consideration, the reasonable parameters of the fueling scenario in these simulations are estimated as pellet radius ${r}_{{\rm{p}}}=3\,{\rm{mm}},$ injection rate $=\,4\,\mathrm{Hz},$ and pellet injection velocity $=\,1000\mbox{-}2000\,{\rm{m}}\,{{\rm{s}}}^{-1}$ without drift or $450\,{\rm{m}}\,{{\rm{s}}}^{-1}$ with high-field-side drift.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gas breakdown mechanism in pulse-modulated asymmetric ratio frequency dielectric barrier discharges

The gas breakdown mechanisms, especially the roles of metastable species in atmospheric pressure pulse-modulated ratio frequency barrier discharges with co-axial cylindrical electrodes, were studied numerically using a one dimensional self-consistent fluid model. Simulation results showed that in low duty cycle cases, the electrons generated from the channels associated with metastable species played a more important role in initializing next breakdown than the direct ionization of helium atoms of electronic grounded states by electron-impact. In order to quantitatively evaluate the contribution to the discharge by the metastables, we defined a “characteristic time” and examined how the value varied with the gap distance and the electrode asymmetry. The results indicated that the lifetime of the metastable species (including He*and He{sub 2}{sup *}) was much longer than that of the pulse-on period and as effective sources of producing electrons they lasted over a period up to millisecond. When the ratio of the outer radius to the inner radius of the cylindrical electrodes was far bigger than one, it was found that the metastables distributed mainly in a cylindrical region around the inner electrode. When the ratio decreased as the inner electrode moved outward, the density of metastables in the discharge region near the outer electrode became gradually noticeable. As the discharging gap continued to decrease, the two hill-shaped distributions gradually merged to one big hill. When the discharge spacing was fixed, asymmetric electrodes facilitated the discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗