Search NASA⌕ Search

Engineering topics

Wang, Zhen

Publications and source records attributed to Wang, Zhen.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Complex-Concentrated Anion Doping Enables Ultra-Stable Lattice Oxygen and Structural Integrity in Lithium-Rich Layered Oxide Cathodes

Lithium- and manganese-rich layered oxides (LMR) stand out as next-generation lithium-ion cathode chemistries, which harness both transition-metal and lattice-oxygen redox processes to deliver exceptional capacity and energy density. However, their full potential is hindered by intrinsic oxygen instability and structural degradation, resulting in pronounced voltage fade and capacity decay. Here, we present a complex-concentrated anion-doping paradigm in which multiple anions, F, Br, and S, are incorporated into the oxygen sublattice to enhance oxygen-redox and structural stability. X-ray absorption spectroscopy and aberration-corrected scanning transmission electron microscopy confirm ultra-stable local oxygen coordination environments during long-term cycling, with detrimental phase transformations and oxygen-loss-induced cavitation dramatically inhibited. Notably, we show that the characteristic LiTM6 transition metal (TM) honeycomb ordering is preserved even after electrochemical cycling. Concurrently, this strategy yields an unprecedented volume change of only 0.63% upon charging to 4.8 V vs. Li+/Li, achieving the first zero-strain LMR cathode. The resulting LMR cathode delivers ultralow voltage fade (1 mV per cycle during the first 100 cycles and becomes negligible in subsequent cycles) and outstanding energy retention (93% after 200 cycles) in a pouch cell configuration. Our complex-concentrated anion-doping concept establishes a broadly applicable strategy for resolving chemo-mechanical failure mechanisms in ceramic intercalation electrodes for next-generation energy storage.

Li-ion batteries↗
DOE OSTI2025

Optoelectronic polymer memristors with dynamic control for power-efficient in-sensor edge computing

Abstract As the demand for edge platforms in artificial intelligence increases, including mobile devices and security applications, the surge in data influx into edge devices often triggers interference and suboptimal decision-making. There is a pressing need for solutions emphasizing low power consumption and cost-effectiveness. In-sensor computing systems employing memristors face challenges in optimizing energy efficiency and streamlining manufacturing due to the necessity for multiple physical processing components. Here, we introduce low-power organic optoelectronic memristors with synergistic optical and mV-level electrical tunable operation for a dynamic “control-on-demand” architecture. Integrating signal sensing, featuring, and processing within the same memristors enables the realization of each in-sensor analogue reservoir computing module, and minimizes circuit integration complexity. The system achieves 97.15% fingerprint recognition accuracy while maintaining a minimal reservoir size and ultra-low energy consumption. Furthermore, we leverage wafer-scale solution techniques and flexible substrates for optimal memristor fabrication. By centralizing core functionalities on the same in-sensor platform, we propose a resilient and adaptable framework for energy-efficient and economical edge computing.

Optics↗
DOE OSTI2024

Microsphere LiMn 0.6 Fe 0.4 PO 4 /C cathode with unique rod-like secondary architecture for high energy lithium ion batteries

LiMn x Fe 1-x PO 4 /C is considered a promising next-generation cathode material with significant commercial potential, inheriting the safety of LiFePO 4 while offering higher energy densities. However, the extremely low conductivity and the Jahn-Teller effect induced by Mn 3+ limit its practical capacity and rate performance. Effective modifications can be achieved through particle nanonization and uniform carbon coating. Here, in this work, we synthesized microspherical LiMn 0.6 Fe 0.4 PO 4 /C cathode materials using a hydrothermal method combined with spray drying carbon coating. The cathode material exhibits a microsphere structure composed of aggregated nanorods with a uniform 3 nm carbon coating, showing good dispersibility, small specific surface area and high tap density. In-situ diffraction analysis showed that expanding the single-phase solid solution region during (de)lithiation can reduce the energy barrier for electron transport, improve the kinetics of the (dis)charge process, and enhance both cycling and rate performance. The initial capacity at 0.1C can reach 155 mAh/g, and the capacity remains at 133.5 mAh/g with a retention rate of 97.1 % after 300 cycles. The synergistic effect of particle nanonization and uniform carbon coating endows the LiMn x Fe 1-x PO 4 /C material with excellent electrochemical performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Deciphering Chemical/Electrochemical Compatibility of Li 3 InCl 6 in 5.2 V High-Voltage LiCoO 2 All-Solid-State Batteries

Large interfacial resistance is a widely recognized impediment to the advancement of high-voltage, all-solid-state batteries. However, a comprehensive understanding of the fundamental cause behind the interfacial resistance between solid electrolytes and typical layered oxide cathodes has not yet been achieved. Here, we investigated the high-voltage stability of Li 3 InCl 6 and elucidated the underlying interfacial electrochemical reactions between LiCoO 2 and Li 3 InCl 6 . Further, the pairing of Li 3 InCl 6 with LiCoO 2 exhibited a superior capacity retention of 73.6% even at 5.2 V, much higher than 28.2% charged at 4.6 V in lithium-ion batteries after 70 cycles. The enhanced high-voltage stability of ASSBs is attributed to the stable interface formed between LiCoO 2 and Li 3 InCl 6 and the reinforced surface and bulk structure stability. On the other hand, the ultrahigh voltage still causes the partial decomposition of Li 3 InCl 6 and generates interfacial compounds such as InClO and cobalt and indium chlorides/oxides.

25 ENERGY STORAGE↗
DOE OSTI2024

Enhanced quantum state transfer by circumventing quantum chaotic behavior

The ability to realize high-fidelity quantum communication is one of the many facets required to build generic quantum computing devices. In addition to quantum processing, sensing, and storage, transferring the resulting quantum states demands a careful design that finds no parallel in classical communication. Existing experimental demonstrations of quantum information transfer in solid-state quantum systems are largely confined to small chains with few qubits, often relying upon non-generic schemes. Here, by using a superconducting quantum circuit featuring thirty-six tunable qubits, accompanied by general optimization procedures deeply rooted in overcoming quantum chaotic behavior, we demonstrate a scalable protocol for transferring few-particle quantum states in a two-dimensional quantum network. These include single-qubit excitation, two-qubit entangled states, and two excitations for which many-body effects are present. Our approach, combined with the quantum circuit’s versatility, paves the way to short-distance quantum communication for connecting distributed quantum processors or registers, even if hampered by inherent imperfections in actual quantum devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Eliminating the Burn‐in Loss of Efficiency in Organic Solar Cells by Applying Dimer Acceptors as Supramolecular Stabilizers

Abstract The meta‐stable active layer morphology of organic solar cells (OSCs) is identified as the main cause of the rapid burn‐in loss of power conversion efficiency (PCE) during long‐term device operation. However, effective strategies to eliminate the associated loss mechanisms from the initial stage of device operation are still lacking, especially for high‐efficiency material systems. Herein, the introduction of molecularly engineered dimer acceptors with adjustable thermal transition properties into the active layer of OSCs to serve as supramolecular stabilizers for regulating the thermal transitions and optimizing the crystallization of the absorber composites is reported. By establishing intimate π‐π interactions with small‐molecule acceptors, these stabilizers can effectively reduce the trap‐state density (N t ) in the devices to achieve excellent PCEs over 19%. More importantly, the lowN t associated with an initially optimized morphology can be maintained under external stresses to significantly reduce the PCE burn‐in loss in devices. This research reveals a judicious approach to improving OPV stability by establishing a comprehensive correlation between material properties, active‐layer morphology, and device performance, for developing burn‐in‐free OSCs.

Chemistry↗
DOE OSTI2024

The role of interfacial donor–acceptor percolation in efficient and stable all-polymer solar cells

Polymerization of Y6-type acceptor molecules leads to bulk-heterojunction organic solar cells with both high power-conversion efficiency and device stability, but the underlying mechanism remains unclear. Here we show that the exciton recombination dynamics of polymerized Y6-type acceptors (Y6-PAs) strongly depends on the degree of aggregation. While the fast exciton recombination rate in aggregated Y6-PA competes with electron-hole separation at the donor–acceptor (D–A) interface, the much-suppressed exciton recombination rate in dispersed Y6-PA is sufficient to allow efficient free charge generation. Indeed, our experimental results and theoretical simulations reveal that Y6-PAs have larger miscibility with the donor polymer than Y6-type small molecular acceptors, leading to D–A percolation that effectively prevents the formation of Y6-PA aggregates at the interface. Besides enabling high charge generation efficiency, the interfacial D–A percolation also improves the thermodynamic stability of the blend morphology, as evident by the reduced device “burn-in” loss upon solar illumination.

14 SOLAR ENERGY↗
DOE OSTI2024

Charge‐Programmable Photopolymers for 3D Electronics via Additive Manufacturing

Charge‐programmed 3D printing enables the fabrication of 3D electronics with lightweight and high precision via selective patterning of metals. This selective metal deposition is catalyzed by Pd nanoparticles that are specifically immobilized onto the charged surface and promises to fabricate a myriad of complex electronic devices with self‐sensing, actuation, and structural elements assembled in a designed 3D layout. However, the achievable property space and the material‐performance correlation of the charge‐programmed printing remain unexplored. Herein, a series of photo‐curable resins are designed for unveiling how the charge and crosslink densities synergistically impact the nanocatalyst‐guided selective deposition in catalytic efficiency and properties of the 3D printed charge‐programmed architectures, leading to high‐quality 3D patterning of solid and liquid metals. The findings offer a wide tunability of the structural properties of the printed electronics, ranging from stiff to extreme flexibility. Capitalizing on these results, the printing and successful application of an ultralight‐weight and deployable 3D multi‐layer antenna system operating at an ultrahigh‐frequency of 19 GHz are demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid Electrolyte Bimodal Grain Structures for Improved Cycling Performance

Here, the application of solid-state electrolytes in Li batteries is hampered by the occurrence of Li-dendrite-caused short circuits. To avoid cell failure, the electrolytes can only be stressed with rather low current densities, severely restricting their performance. As grain size and pore distributions significantly affect dendrite growth in ceramic electrolytes such as Li 7 La 3 Zr 2 O 12 and its variants; here, a “detour and buffer” strategy to bring the superiority of both coarse and fine grains into play, is proposed. To validate the mechanism, a coarse/fine bimodal grain microstructure is obtained by seeding unpulverized large particles in the green body. The rearrangement of coarse grains and fine pores is fine-tuned by changing the ratio of pulverized and unpulverized powders. The optimized bimodal microstructure, obtained when the two powders are equally mixed, allows, without extra interface decoration, cycling for over 2000 h as the current density is increased from 1.0 mA·cm -2 , and gradually, up to 2.0 mA·cm -2 . The “detour and buffer” effects are confirmed from postmortem analysis. The complex grain boundaries formed by fine grains discourage the direct infiltration of Li. Simultaneously, the coarse grains further increase the tortuosity of the Li path. This study sheds light on the microstructure optimization for the polycrystalline solid-state electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2024

Surface termination effect of $\mathrm{SrTiO_3}$ substrate on ultrathin $\mathrm{SrRuO_3}$

A uniform 1-unit-cell-high step on the SrTiO 3 (STO) substrate is a prerequisite for growing high-quality epitaxial oxide heterostructures. However, it is inevitable that defects induced by mixed substrate-surface termination exist at the interface, significantly impacting the properties of ultrathin films. Here we microscopically identify the origin for the lateral inhomogeneity in the growth of ultrathin SrRuO3 films due to the step effects of SrTiO 3 (001). By using atomic-resolved scanning transmission electron microscopy, we observe two distinct types of step propagation along the [011] and [$0\bar{1}1$] crystallographic direction in SrTiO 3 -SrRuO 3 heterostructures, respectively. In particular, the type-II [$0\bar{1}1$] step results in lateral discontinuity of monolayer SrRuO 3 and originates from the SrO-terminated regions along the TiO 2 -terminated step edge. Such an induced lateral discontinuity should be responsible for the distinct electronic and magnetic properties of monolayer SrRuO 3 . Our findings underscore the critical importance of using single-termination STO substrate to achieve high-quality termination-selective films and to unveil the intrinsic properties of epitaxial films in the atomic limit.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Supramolecular assembly of blue and green halide perovskites with near-unity photoluminescence

The metal-halide ionic octahedron is the optoelectronic unit for halide perovskites, and a crown ether–assisted supramolecular assembly approach can pack various ionic octahedra into tunable symmetries. In this work, we demonstrate near-unity photoluminescence quantum yield (PLQY) blue and green emission with the supramolecular assembly of hafnium (Hf) and zirconium (Zr) halide octahedral clusters. (18C6@K) 2 HfBr 6 powders showed blue emission with a near-unity PLQY (96.2%), and green emission was also achieved with (18C6@K) 2 ZrCl 4 Br 2 powders at a PLQY of 82.7%. In conclusion, these highly emissive powders feature facile low-temperature solution-based synthesis conditions and maintain high PLQY in solution-processable semiconductor inks under ambient conditions, and they were used in thin-film displays and emissive three-dimensional–printed architectures that exhibited high spatial resolution.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thickness dependent OER electrocatalysis of epitaxial thin film of high entropy oxide

High entropy oxides (HEOs), which contain multiple elements in the same crystallographic site, are a promising platform for electrocatalysis in oxygen evolution reaction (OER). Investigating these materials in epitaxial thin film form expands the possibility of tuning OER activity by several means, which are not realizable in polycrystalline samples. To date, very few such studies have been reported. In this work, the OER activity of single-crystalline thin films of (La 0.2 Pr 0.2 Nd 0.2 Sm 0.2 Eu 0.2 )NiO 3 , grown on NdGaO 3 substrates have been investigated in 0.1 M KOH electrolyte as a function of film thickness. The OER activity increases with the thickness of the film. X-ray absorption spectroscopy measurements find an increase in Ni $d$-O $p$ covalency and a decrease in charge transfer energy with the increase in film thickness. These facilitate higher charge transfer between Ni and surface adsorbates, increasing OER activity. However, the OER process leads to excessive leaching of thicker films and the OER activity of a 75 unit cell thick film is found to be optimal in the present study. In conclusion, this work demonstrates that the thickness of perovskite oxides can be used as a parameter to enhance OER activity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Engineering Active Surface Oxygen Sites of Cubic Perovskite Cobalt Oxides toward Catalytic Oxidation Reactions

Unraveling the role of surface oxygen sites in transition metal oxides during catalytic reactions has always been the focus of environmental and energy chemistry research. For this work, active surface oxygen sites of cubic perovskite cobalt oxide were engineered to comprehend their crucial role and catalytic mechanism at the molecular level. By removing those inert Sr/La–O termination layers, active oxygen sites were exposed on the Co terminated surface of Sr 0.6 La 0.4 CoO 3–δ that furnished the dominant catalytic process of CO oxidation via the Mars–van Krevelen (MvK) mechanism. The fabrication of five-coordinate cobalt ions and the enhanced covalency of Co–O bonds not only optimize the surface electronic structure of Co 3d–O 2p, but also supply active surface oxygen sites, which effectively oxidizes CO to CO 2 with a significantly improved oxidation performance and stability as evidenced by soft/hard XAS, XPS, and O 2 -TPD. Furthermore, online isotopic 18 O 2 mass spectrometry, in situ DRIFTS, and theoretical simulation demonstrate that the activity of surface oxygen sites enhances the kinetics of the MvK reaction, while unsaturated coordination sites from five-coordinate cobalt ions primarily contribute to the activated oxygen molecules and the stable catalytic cycle. The results reported here provide a deep insight into the comprehension of the relationships among active oxygen sites, surface electronic structure, and the reaction mechanism of transition metal oxides necessary for catalytic oxidation reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Tuning structural, transport, and magnetic properties of epitaxial SrRu O 3 through Ba substitution

The perovskite ruthenates (A RuO 3 , A=Ca, Ba, or Sr) exhibit unique properties owing to a subtle interplay of crystal structure and electronic-spin degrees of freedom. Here, in this study, we demonstrate an intriguing continuous tuning of crystal symmetry from orthorhombic to tetragonal (no octahedral rotations) phases in epitaxial SrRuO 3 achieved via Ba substitution (Sr 1-x Ba x RuO 3 with 0 ≤ x ≤ 0.7 ). An initial Ba substitution to SrRuO 3 not only changes the ferromagnetic properties, but also tunes the perpendicular magnetic anisotropy via flattening the Ru–O–Ru bond angle (to 180°), resulting in the maximum Curie temperature and an extinction of RuO 6 rotational distortions at x≈0.20. For x ≤ 0.2, the reduction of RuO 6 octahedral rotational distortion dominantly enhances the ferromagnetism in the system, though competing with the effect of the RuO 6 tetragonal distortion. Further increasing Ba substitution (x > 0.2) gradually enhances the tetragonal-type distortion, resulting in the tuning of Ru-4d orbital occupancy and suppression of ferromagnetism. Our results demonstrate that isovalent substitution of the A-site cations significantly and controllably impacts both electronic and magnetic properties of perovskite oxides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Design and additive manufacturing of optimized electrodes for energy storage applications

Supercapacitors exhibit fast charging/discharging ability and have attracted considerable attention within the automotive, aerospace, and telecommunication industries. Porous carbons, prized for their high electrical conductivity and high surface area, have been attractive candidates for supercapacitor electrodes. Moving to thick electrodes is one strategy to further increase energy density due to a higher volume fraction of active material. However, thick electrodes suffer from sluggish charged species transport, which is why thin electrodes are currently favored. In this work, we investigate the use of computational optimization and additive manufacturing to design and fabricate thick porous electrodes with improved performance. Electrode performance was maximized by designing their morphologies via topology optimization and printing by projection micro stereolithography (PμSL) using commercial resin (PR48). The PR48 resin was then pyrolyzed (PR48-P) to create the final conductive electrode. The optimized PR48-P electrodes exhibited 99% improvement in capacitance compared to control electrodes printed with cubic lattice morphologies. To further improve performance, we formulated a resin combining graphene oxide (GO) and trimethylolpropane triacrylate (TMPTA). Electrodes printed with 3 wt% GO in TMPTA exhibited improved capacitance retention after pyrolysis compared to the PR48-P electrodes. Finally, this work demonstrates the benefits of using topology optimization to design electrodes and material development to improve functional properties of 3D printable electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Non-Centrosymmetric Sr 2 IrO 4 Obtained Under High Pressure

Sr 2 IrO 4 with strong spin-orbit coupling (SOC) and Hubbard repulsion (U) hosts Mott insulating states. The similar crystal structure, magnetic and electronic properties, particularly the d-wave gap observed in Sr 2 IrO 4 enhanced the analogies to cuprate high-$T_c$ superconductor, La 2 CuO 4 . The incomplete analogy was due to the lack of broken inversion symmetry phases observed in Sr 2 IrO 4 . Here, under high pressure and high temperature conditions, we report a non-centrosymmetric Sr 2 IrO 4 . The crystal structure and its noncentrosymmetric character were determined by single crystal X-ray diffraction and high-resolution scanning transmission electron microscopy (HR-STEM). The magnetic characterization confirms the Ir 4+ with $\textit{S}$ = 1/2 at low temperature in Sr 2 IrO 4 with magnetic ordering occurred at around 86 K, where a larger moment is observed than the ambient pressure Sr 2 IrO 4 . Moreover, the resistivity measurement shows three-dimensional Mott variable-range hopping existed in the system. Further, this non-centrosymmetric Sr 2 IrO 4 phase appears to be a unique material to offer further understanding of high-$T_c$ superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Emergent ferromagnetism and insulator-metal transition in δ-doped ultrathin ruthenates

Abstract Heterostructures of complex transition metal oxides are known to induce extraordinary emergent quantum states that arise from broken symmetry and other discontinuities at interfaces. Here we report the emergence of unusual, thickness-dependent properties in ultrathin CaRuO 3 films by insertion of a single isovalent SrO layer (referred to as δ-doping). While bulk CaRuO 3 is metallic and nonmagnetic, films thinner than or equal to ~15-unit cells (u.c.) are insulating though still nonmagnetic. However, δ-doping to middle of such CaRuO 3 films induces an insulator-to-metal transition and unusual ferromagnetism with strong magnetoresistive behavior. Atomically resolved imaging and density-functional-theory calculations reveal that the whole δ-doped film preserves the bulk-CaRuO 3 orthorhombic structure, while appreciable structural and electronic changes are highly localized near the SrO layer. The results highlight delicate nature of magnetic instability in CaRuO 3 and subtle effects that can alter it, especially the role of A-site cation in electronic and magnetic structure additional to lattice distortion in ruthenates. It also provides a practical approach to engineer material systems via highly localized modifications in their structure and composition that may offer new routes to the design of oxide electronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗