Search NASA⌕ Search

Engineering topics

Warren, Charles David

Publications and source records attributed to Warren, Charles David.

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Mechanical and Corrosion Assessment of Friction Self-Piercing Rivet Joint of Carbon Fiber-Reinforced Polymer and Magnesium Alloy AZ31B

In the present work, thermoset carbon fiber–reinforced polymer (CFRP) was spot joined to magnesium alloy AZ31B by a friction self-piercing riveting (F-SPR) process. Lap shear tensile and cross-tension testing were used to evaluate the mechanical joint performance. An average lap shear tensile load of 5.18 kN was achieved, while an average of 2.81 kN was found from cross-tension testing. All F-SPR samples showed a pullout of AZ31B after mechanical testing, indicating good mechanical interlocking between the steel rivet and AZ31B. Corrosion potential was measured for each material to establish the galvanic corrosion characteristics. As expected, AZ31B was found to be the most active, while thermoset CFRP was the most noble. The steel rivet fell between the AZ31B (active) and the thermoset CFRP (noble). Salt fog corrosion testing (ASTM B-117) was performed to evaluate the corrosion performance of the uncoated F-SPR joint. With up to 200 h of exposure, the post-corroded F-SPR joint integrity retained 81.2% of the pre-exposure F-SPR joint strength with AZ31B pullout failure mode. From cross-sectional analysis of the F-SPR joint, extensive corrosion of AZ31B was observed at the joint and other exposure areas. However, steel rivet was not significantly corroded due to sacrificial anode effect by which AZ31B corroded first in the galvanic couple.

36 MATERIALS SCIENCE↗

Joining of Lightweight Dissimilar Materials by Friction Self-Piercing Riveting

In this work, we employed a unique solid-state joining process, friction self-piercing riveting (F-SPR), to join carbon fiber composites to the low-ductility magnesium alloy AZ31B. The localized frictional heat generated between the rotating rivet and the underside of the magnesium sheet softened and prevented crack generation in AZ31B. A consumable joining rivet was designed to join the selected material stacks by F-SPR. Lap shear tensile testing was used to assess the joint quality of specimens produced by F-SPR. The joint interface from the cross-sectioned F-SPR specimen was evaluated by optical microscopy.

Lim, Yong Chae↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Surface characterization of carbon fiber polymer composites and aluminum alloys after laser interference structuring

Here, the increasing use of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) and aluminum alloys as lightweight materials in the automotive and aerospace industries demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using an Nd:YAG laser in a two-beam interference setup, enabling the (a) structuring of the AL 5182 surface, (b) removal of the resin layer on top of carbon fibers, and (c) structuring of the carbon fibers. CFPC specimens of T700S carbon fiber, Prepreg - T8 3 epoxy, 5 ply thick, 0/90o plaques were used. The effect of laser fluence, scanning speed, and number of shots-per-spot was investigated on the removal rate of the resin without an excessive damage of the fibers. Optical micrographs, 3D imaging, and scanning electron microscope (SEM) imaging were used to study the effect of the laser processing on surface morphology.

36 MATERIALS SCIENCE↗

A LASER INTERFERENCE-BASED SURFACE TREATMENT OF AL AND CARBON FIBER POLYMER COMPOSITES FOR ENHANCED BONDING

Due to its increased use in the automotive and aerospace industries, joining of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) to metals demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using a new laser based technique, in which the laser interference power profile was created by splitting the beam and guiding those beams to the sample surface by overlapping each other with defined angles to each other. Results were presented for the overlap shear testing of single-lap joints made with Al 5182 and CFPC specimens whose surfaces prepared by (a) surface abrasion and solvent cleaning; and (b) laser-interference structured surfaces by rastering with a 4 mm laser beam at approximately 3.5 W power. CFPC specimens of T700S carbon fiber, Prepreg T70 epoxy, 4 or 5 ply thick, 0/90o plaques were used. Adhesive DP810 was used to bond Al and CFPC. The bondline was 0.25mm and the bond length was consistent among all joints produced. First, the effect of the laser speed on the joint performance was evaluated by laser-interference structure Al and CFPC surfaces with a beam angle of 3o and laser beam speeds of 3, 5, and 10 mm/s. For this sensitivity study, 3 joint specimens were used per each joint type. Based on the results for minimum, maximum, and mean values for the shear lap strength and maximum load for all the 9 joint types, two joint types were selected for further evaluations. Six additional joint specimens were prepared for these two joint types in order to obtain better statistics and the shear test data was presented for the range, mean, and standard deviation. The results for the single-lap shear tests obtained for six joint specimens, indicate that the shear lap strength, maximum load, and displacement at maximum load for those joints made with laser-interference structured surfaces were increased by approximately 14.8%, 16%, and 100%, respectively over those measured for the baseline joints.

Sabau, Adrian S↗

SURFACE MORPHOLOGY OF CARBON FIBER POLYMER COMPOSITES AFTER LASER STRUCTURING

The increasing use of Carbon Fiber Polymer Composite (CFPC) as a lightweight material in automotive and aerospace industries requires the control of surface morphology. In this study, the composites surface was prepared by ablating the resin in the top fiber layer of the composite using an Nd:YAG laser. The CFPC specimens with T700S carbon fiber and Prepreg - T83 resin (epoxy) were supplied by Plasan Carbon Composites, Inc. as 4 ply thick, 0/90o plaques. The effect of laser fluence, scanning speed, and wavelength was investigated to remove resin without an excessive damage of the fibers. In addition, resin ablation due to the power variation created by a laser interference technique is presented. Optical property measurements, optical micrographs, 3D imaging, and high-resolution optical profiler images were used to study the effect of the laser processing on the surface morphology.

Sabau, Adrian S↗

Aluminum Surface Texturing by Means of Laser Interference Metallurgy

The increasing use of lightweight materials, such as aluminum alloys, in auto body structures requires more effective surface cleaning and texturing techniques to improve the quality of the structural components. The present work introduces a novel surface treatment method using laser interferometry produced by two beams of a pulsed Nd:YAG laser operating at 10Hz of frequency to clean aluminum surfaces, and meanwhile creating periodic and rough surface structures. The influences of beam size, laser fluence, wavelength, and pulse number per spot are investigated. High resolution optical profiler images reveal the change of the peak-to-valley height on the laser-treated surface.

Chen, Jian↗

Low Cost Carbon Fibre for Automotive Applications Part 1: Low Cost Carbon Fibre Development

In pursuit of the goal to produce ultra-lightweight fuel efficient vehicles, there has been great excitement during the last few years about the potential for using carbon fibre reinforced composites in high volume applications. Currently, the greatest hurdle that inhibits wider implementation of carbon fibre composites in transportation is the high cost of carbon fibre when compared to other candidate materials. However, significant research is being conducted to develop lower cost, high volume technologies for producing carbon fibre. This chapter will highlight ongoing research in this area.

Automotive↗

Low Cost Carbon Fibre: Applications, Performance and Cost Models - Chapter 17

Weight saving in automotive applications has a major bearing on fuel economy. It is generally accepted that, typically, a 10% weight reduction in an automobile will lead to a 6-8% improvement in fuel economy. In this respect, carbon fibre composites are extremely attractive in their ability to provide superlative mechanical performance per unit weight. That is why they are specified for high-end uses such as Formula 1 racing cars and the latest aircraft (e.g. Boeing 787, Airbus A350 and A380), where they comprise over 50% by weight of the structure However, carbon fibres are expensive and this renders their composites similarly expensive. Research has been carried out at Oak Ridge National Laboratories (ORNL), Tennessee, USA for over a decade with the aim of reducing the cost of carbon fibre such that it becomes a cost-effective option for the automotive industry. Aspects of this research relating to the development of low cost carbon fibre have been reported in Chapter 3 of this publication. In this chapter, the practical industrial applications of low-cost carbon fibre are presented, together with considerations of the performance and cost models which underpin the work.

Warren, Charles David↗

CARBON FIBER COMPOSITES IN HIGH VOLUME

Vehicle lightweighting represents one of several design approaches that automotive and heavy truck manufacturers are currently evaluating to improve fuel economy, lower emissions, and improve freight efficiency (tons-miles per gallon of fuel). With changes in fuel efficiency and environmental regulations in the area of transportation, the next decade will likely see considerable vehicle lightweighting throughout the ground transportation industry. Greater use of carbon fiber composites and light metals is a key component of that strategy. This paper examines the competition between candidate materials for lightweighting of heavy vehicles and passenger cars. A 53-component, 25 % mass reduction, body-in-white cost analysis is presented for each material class, highlighting the potential cost penalty for each kilogram of mass reduction and then comparing the various material options. Lastly, as the cost of carbon fiber is a major component of the elevated cost of carbon fiber composites, a brief look at the factors that influence that cost is presented.

AHSS↗

Surface Treatment of Carbon Fibers by Continuous Gaseous System

The mechanical performance of carbon fiber-polymer composites strongly depends on interfacial adhesion, which is function of types of carbon fiber, surface chemistry, physical and chemical interactions, and mechanical interlocking. Untreated and unsized high strength carbon fibers were oxidized by continuous thermochemical and atmospheric plasma treatment. Surface properties were investigated before and after treatment (chemistry, topography), as well as their mechanical properties. X-ray photoelectron spectroscopy revealed a significant increase of the oxygen atomic content from 3% to around 20% and the analysis of the carbon peak showed that carboxylic acid functionalities and hydroxyl groups were generated. An observation of the fiber surface by scanning electron microscopy and atomic force microscopy did not show any dramatic change of the fiber morphology and surface topography. A Raman spectroscopy analysis exhibited that the weak boundary layers and debris remaining at the surface of untreated fibers were removed. No significant damage of the mechanical properties (tensile strength) was noticed. The influence of the changes of the surface properties on interfacial adhesion of carbon fiber-epoxy and -vinyl ester matrix was evaluated using 90 flexural and short beam shear tests with unidirectional coupons. A significant increase of the 90 flexural and short beam shear strength showed that the interfacial adhesion between carbon fibers and epoxy resins was improved. The observation of the fracture profile by scanning electron microcopy confirmed those results, as the rupture of the coupons after surface treatment was more cohesive.

36 MATERIALS SCIENCE↗

Development of Commodity Grade, Lower Cost Carbon Fiber - Commercial Applications

In pursuit of the goal to produce ultra-lightweight fuel efficient vehicles, there has been great excitement during the last few years about the potential for using carbon fiber reinforced composites in high volume applications. Currently, the greatest hurdle that inhibits wider implementation of carbon fiber composites in transportation is the high cost of the fiber when compared to other candidate materials. As part of the United States Department of Energy s FreedomCAR initiative, significant research is being conducted to develop lower cost, high volume technologies for producing carbon fiber. This paper will highlight the on-going research in this area. Through Department of Energy (DOE) sponsorship, Oak Ridge National Laboratory (ORNL) and its partners have been working with the US Automotive Composites Consortium (ACC) to develop technologies that would enable the production of carbon fiber at 5-7 dollars per pound. Achievement of this cost goal would allow the introduction of carbon fiber based composites into a greater number of applications for future vehicles. The approach has necessitated the development of both alternative precursors and more efficient production methods. Alternative precursors under investigation include textile grade polyacrylonitrile (PAN) fibers and fibers from lignin-based feedstocks. Previously, as part of the research program, Hexcel Corporation developed the science necessary to allow textile grade PAN to be used as a precursor rather than typical carbon fiber grade precursors. Efforts are also underway to develop carbon fiber precursors from lignin-based feedstocks. ORNL and its partners are working on this effort with domestic pulp and paper producers. In terms of alternative production methods, ORNL has developed a microwave-based carbonization unit that can process pre-oxidized fiber at over 200 inches per minute. ORNL has also developed a new method of high speed oxidation and a new method for precursor stabilization. Additionally, novel methods of activating carbon fiber surfaces have been developed which allow atomic oxygen concentrations as high as 25-30% to be achieved rather than the more typical 4-8% achieved by the standard industrial ozone treatment.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗