Engineering topics
Publications and source records attributed to Waters, W. J..
"EX-212" denotes high-density extruded form of composite solid material self-lubricating over wide range of temperatures. Properties equal or exceed those of powder-metallurgy version of this material. Developed for use in advanced engines at high temperatures at which ordinary lubricants destroyed.
Research has been underway at the NASA Lewis Research Center since the 1960's to develop high temperature, self-lubricating materials. The bulk of the research has been done in-house by a team of researchers from the Materials Division. A series of self-lubricating solid material systems has been developed over the years. One of the most promising is the composite material system referred to as PS-212 or PM-212. This material is a powder metallurgy product composed of metal bonded chromium carbide and two solid lubricating materials known to be self-lubricating over a wide temperature range. NASA feels this material has a wide potential in industrial applications. Simplified processing of this material would enhance its commercial potential. Processing changes have the potential to reduce processing costs, but tribological and physical properties must not be adversely affected. Extrusion processing has been employed in this investigation as a consolidation process for PM-212/PS-212. It has been successful in that high density bars of EX-212 (extruded PM-212) can readily be fabricated. Friction and strength data indicate these properties have been maintained or improved over the P.M. version. A range of extrusion temperatures have been investigated and tensile, friction, wear, and microstructural data have been obtained. Results indicate extrusion temperatures are not critical from a densification standpoint, but other properties are temperature dependent.
An upper plate having ink flow channels and a lower plate having a multicolored pattern are joined. The joining is accomplished without clogging any ink flow paths. A pattern having different colored parts and apertures is formed in a lower plate. Ink flow channels each having respective ink input ports are formed in an upper plate. The ink flow channels are coated with solder mask and the bottom of the upper plate is then coated with solder. The upper and lower plates are pressed together at from 2 to 5 psi and heated to a temperature of from 295 F to 750 F or enough to melt the solder. After the plates have cooled and the pressure is released, the solder mask is removed from the interior passageways by means of a liquid solvent.
Improved joining method uses wave-soldering techniques developed for integrated-circuit-board assemblies. Thermosetting plastic is replaced by wave soldering, which applies a thin even coat of solder to mating copper surfaces. This is done after ink holes and channels have been protected by water-soluble, high-temperature solder mask which prevents wetting and clogging.
Strengthening and forming process for prealloyed powder superalloys greatly increases material strength in the 900-1,200F temperature range. Process which involves superplastically-deforming compacted powders at controlled rates and temperature is most effective on nickel-base alloys.
A technique involving superplastic processing and high-pressure autoclaving was applied to a nickel-base prealloyed powder alloy. Tensile strengths as high as 2865 MN/sq m (415 ksi) at 480 C (900 F) were obtained with as-superplastically deformed material. Appropriate treatments yielding materials with high-temperature tensile and stress-rupture strengths (980 C (1800 F)) were also devised.
A nickel base superalloy for use at temperatures of 2000 F (1095 C) to 2200 F (1205 C) was developed for use as stator vane material in advanced gas turbine engines. The alloy has a nominal composition in weight percent of 16 tungsten, 7 aluminum, 1 molybdenum, 2 columbium, 0.3 zirconium, 0.2 carbon and the balance nickel.
The combined effects of temperature and pressure on the resulting density of a sialon (i.e., a ceramic composed of Si, Al, O, and N) are evaluated. Pressures in the 3.5-27.5 MPa range and temperatures in the 1550-1750 C range are considered. It is found that: (1) fully dense sialon bodies may be produced at lower temperatures than those usually used in the field, (2) the phase equilibrium reaction is increased by increased pressure, (3) the iso-density contour may be used to help design the desired microstructure, (4) phase changes occurring in the sample during hot pressing influenced sialon densification to a large extent, and (5) microstructures exceeding 98% theoretical density suggest that plastic deformation has contributed to densification.
A technique involving superplastic processing and high pressure autoclaving was applied to a nickel base prealloyed powder alloy. Tensile strengths as high as 2865 MN/sq m at 480 C were obtained with as-superplastically deformed material. Appropriate treatments yielding materials with high temperature tensile and stress rupture strengths were also devised.
Cast nickel-base alloy designated as NASA TAZ-8A has been developed for use in high temperature aircraft engine components. TAZ-8A composition is 8Ta, 6Cr, 6A1, 4Mo, 4W, 2Cb, 0.5Zr, 0.125C, 0.004B, and balance Ni (weight percent). Its specific gravity at room temperature is 8.65.
The higher inlet-gas temperatures in new aircraft turbine engines make it necessary to use improved superalloys in engine design. Such superalloys are provided by WAZ alloys. NASA has explored the Ni-W-Al system in an attempt to find higher-strength nickel-based alloys for use as stator vane materials. Critical performance goals have been met with the new alloy WAZ-16. With suitable protective coatings, WAZ-16 appears to have considerable potential for high-temperature stator vane applications.
Alloy product is high strength, high temperature nickel base material with higher incipient melting temperature than all known nickel base alloys. It is microstructurally stable and has high impact resistance both before and after prolonged thermal exposure. It contains relatively few alloying constitutents and low content of expensive and rare metals.
A nickel-base superalloy based on the nickel-aluminum-tungsten system designated WAZ-16 was developed for high strength in the 1095 C (2000 F) to 1205 C (2200 F) range. Its tensile strength at the latter temperature is approximately 186 MN/m2 (27,000 psi). The combination of properties of the alloy suggest that it has potential as a stator vane material in advanced gas turbine engines.
A highly alloyed superalloy material is obtained using prealloyed powders. The material is easily shaped at high temperatures when it becomes superplastic because of its particular microstructure.
Heat treating a product material of prealloyed powders after shaping by superplastic deformation restores the ability of the material to resist deformation at high temperatures. Heat treating is accomplished by heating to a temperature between the solidus and liquidus with the application of isostatic pressure to close any voids. This pressure may be simultaneously applied while the material is at the heat treating temperature. The pressure may also be applied when the material cools to a temperature between that at which it is shaped and the solidus.
Application of prealloyed powder technology to the NASA-TRW-VI-A alloy shows the potential of highly alloyed normally cast superalloys for achieving superior properties at intermediate temperatures.
Heat treatment process involves heating products to a temperature above the solidus, and subsequently applying pressure at a temperature below the solidus. Technique can be modified to one step process involving simultaneous application if both high pressure and heat. Process is not limited to cobalt-base alloys.
Bar stock of the NASA-TRW 6-A alloy was made by prealloyed powder techniques and its properties evaluated over a range of temperatures. Room temperature ultimate tensile strength was 1894 MN/sq m (274 500 psi). The as-extruded powder product showed substantial improvements in strength over the cast alloy up to 649 C (1200 F) and superplasticity at 1093 C (2000 F). Both conventional and autoclave heat treatments were applied to the extruded powder product. The conventional heat treatment was effective in increasing rupture life at 649 and 704 C (1200 and 1300 F); the autoclave heat treatment, at 760 and 816 C (1400 and 1500 F).